Jarosław Bartnicki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jarosław Bartnicki has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Zbigniew Pater
Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland
13 shared publications - Janusz Tomczak
Lublin University of Technology, Lublin, Poland
9 shared publications - Grzegorz Samołyk
The Department of Computer Modeling and Technology of Metal Forming, The Lublin Technical University, Lublin, Poland
2 shared publications Janusz Tomczak
2 shared publications- Tomasz Bulzak
Lublin University of Technology
2 shared publications - Xuedao Shu
School of Mechanical Engineering and Intelligent Manufacturing, Ningbo University, Ningbo 315211, China
2 shared publications
Latest Publications
- Open Access
- 28 October 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (1) , 132-147
Analysis and prospects of efficient and precise forming technology for aeroengine turbine shafts
The turbine shaft is a crucial core component of aeroengines, made of difficult-to-deform high-temperature alloy materials, characterized as a long hollow stepped shaft with deep internal holes. Achieving efficient, high-performance, and precise manufacturing of turbine shafts is a cutting-edge...
- 28 October 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (1) , 132-147
Open AccessAnalysis and prospects of efficient and precise forming technology for aeroengine turbine shafts
The turbine shaft is a crucial core component of aeroengines, made of difficult-to-deform high-temperature alloy materials, characterized as a long hollow stepped shaft with deep internal holes. Achieving efficient, high-performance, and precise manufacturing of turbine shafts is a cutting-edge...
- 27 August 2024
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
Asymmetric Cooling Process for Towing Hooks Forgings
The essence of the new solution is the implementation of asymmetric cooling technology for forgings made of 38MnVS6 and 30MnVS6 steel in order to homogenize the mechanical properties through precipitation hardening. The developed process for forgings with significant cross-sectional asymmetry was...
- 27 August 2024
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
Asymmetric Cooling Process for Towing Hooks Forgings
The essence of the new solution is the implementation of asymmetric cooling technology for forgings made of 38MnVS6 and 30MnVS6 steel in order to homogenize the mechanical properties through precipitation hardening. The developed process for forgings with significant cross-sectional asymmetry was...
- 1 June 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 66, 145-152
Effect of process parameters on microscopic uniformity of cross wedge rolling of GH4169 alloy shaft
- 1 June 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 66, 145-152
Effect of process parameters on microscopic uniformity of cross wedge rolling of GH4169 alloy shaft
- Open Access
The Chosen Aspects of Skew Rolling of Hollow Stepped Shafts
The paper presents chosen aspects of the skew rolling process of hollow stepped products with the use of a skew rolling mill designed and manufactured at the Lublin University of Technology. This machine is characterized by the numerical control of spacing between the working rolls and the sequence of the gripper axial movement, which allows for the individual programming of the obtained shapes of parts such as stepped axles and shafts. The length of these zones and the values of possibly realizable cross-section reduction and obtained outlines are the subject of this research paper. The chosen results regarding the influence of the technological parameters used on the course of the process are shown in the present study. Numerical modelling using the finite element method in Simufact Forming, as well as the results of experimental tests performed in a skew rolling mill, were applied in the conducted research. The work takes into account the influence of cross-section reduction of the hollow parts and the feed rate per rotation on the metal flow mechanisms in the skew rolling process. The presented results concern the obtained dimensional deviations and changes in the wall thickness determining the proper choice of technological parameters for hollow parts formed by the skew rolling method. Knowledge about the cause of the occurrence of these limitations is very important for the development of this technology and the choice of the process parameters.
Open AccessThe Chosen Aspects of Skew Rolling of Hollow Stepped Shafts
The paper presents chosen aspects of the skew rolling process of hollow stepped products with the use of a skew rolling mill designed and manufactured at the Lublin University of Technology. This machine is characterized by the numerical control of spacing between the working rolls and the sequence of the gripper axial movement, which allows for the individual programming of the obtained shapes of parts such as stepped axles and shafts. The length of these zones and the values of possibly realizable cross-section reduction and obtained outlines are the subject of this research paper. The chosen results regarding the influence of the technological parameters used on the course of the process are shown in the present study. Numerical modelling using the finite element method in Simufact Forming, as well as the results of experimental tests performed in a skew rolling mill, were applied in the conducted research. The work takes into account the influence of cross-section reduction of the hollow parts and the feed rate per rotation on the metal flow mechanisms in the skew rolling process. The presented results concern the obtained dimensional deviations and changes in the wall thickness determining the proper choice of technological parameters for hollow parts formed by the skew rolling method. Knowledge about the cause of the occurrence of these limitations is very important for the development of this technology and the choice of the process parameters.
- Open Access
Limits of the Process of Rotational Compression of Hollow Stepped Shafts
This article presents the results of theoretical–experimental testing of the process of rotational compression of hollow stepped shafts. The advantages of the technology and the potential area of its application were discussed. Further on, the limits of the rotational compression technology, preventing the manufacturing of high-quality products, were presented. The research was conducted on the basis of numerical modelling using the finite element method in Simufact Forming, as well as the results of experimental tests performed in a forging machine for rotational compression. On the basis of the results obtained, it can be stated that the process of rotational compression of hollow stepped shafts can be hindered by the following phenomena: uncontrolled slip, deformation of the semi-finished product wall, twisting of the formed steps, material cracking, and deformation of the cross-section of the formed steps. The possibility of those hindrances occurring depends heavily on the assumed technological parameters of the process. For this reason, knowledge of the cause of occurrence of those limitations is vital for the development of the technology and the choice of the process parameters.
Open AccessLimits of the Process of Rotational Compression of Hollow Stepped Shafts
This article presents the results of theoretical–experimental testing of the process of rotational compression of hollow stepped shafts. The advantages of the technology and the potential area of its application were discussed. Further on, the limits of the rotational compression technology, preventing the manufacturing of high-quality products, were presented. The research was conducted on the basis of numerical modelling using the finite element method in Simufact Forming, as well as the results of experimental tests performed in a forging machine for rotational compression. On the basis of the results obtained, it can be stated that the process of rotational compression of hollow stepped shafts can be hindered by the following phenomena: uncontrolled slip, deformation of the semi-finished product wall, twisting of the formed steps, material cracking, and deformation of the cross-section of the formed steps. The possibility of those hindrances occurring depends heavily on the assumed technological parameters of the process. For this reason, knowledge of the cause of occurrence of those limitations is vital for the development of the technology and the choice of the process parameters.
- Open Access
Prediction of Crack Formation for Cross Wedge Rolling of Harrow Tooth Preform
The article presents the issue of material fracture during the process of cross-wedge rolling (CWR). The object of the research was the process of forming a harrow tooth preform. In the conducted analysis nine damage criteria were applied. The critical value of damage was determined with a new calibrating test, basing on rotational compression of a sample in a channel. The results of calculations were compared to the results of experimental testing performed in laboratory conditions in Lublin University of Technology. On the basis of the obtained results an assessment of the applied damage criteria and their applicability in the analysis of CWR processes was conducted.
Open AccessPrediction of Crack Formation for Cross Wedge Rolling of Harrow Tooth Preform
The article presents the issue of material fracture during the process of cross-wedge rolling (CWR). The object of the research was the process of forming a harrow tooth preform. In the conducted analysis nine damage criteria were applied. The critical value of damage was determined with a new calibrating test, basing on rotational compression of a sample in a channel. The results of calculations were compared to the results of experimental testing performed in laboratory conditions in Lublin University of Technology. On the basis of the obtained results an assessment of the applied damage criteria and their applicability in the analysis of CWR processes was conducted.
- Open Access
Thermomechanical Analysis of a Helical-Wedge Rolling Process for Producing Balls
The paper presents a complete numerical model of a helical-wedge rolling process for producing balls. The model was designed in Finite Element Method (FEM)-based Forge NxT v.1.1 that enables the simulation of both forming and separating balls. A comparison of numerical results with experimental findings revealed a very high agreement in both qualitative and quantitative terms. The developed numerical model was used to investigate the effect of flange shape on the helical-wedge rolling process for producing balls with a diameter of 125 mm. Three types of flange tools were investigated, and the best results were obtained for a wedge-shaped flange.
Open AccessThermomechanical Analysis of a Helical-Wedge Rolling Process for Producing Balls
The paper presents a complete numerical model of a helical-wedge rolling process for producing balls. The model was designed in Finite Element Method (FEM)-based Forge NxT v.1.1 that enables the simulation of both forming and separating balls. A comparison of numerical results with experimental findings revealed a very high agreement in both qualitative and quantitative terms. The developed numerical model was used to investigate the effect of flange shape on the helical-wedge rolling process for producing balls with a diameter of 125 mm. Three types of flange tools were investigated, and the best results were obtained for a wedge-shaped flange.
- Open Access
- 18 September 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 190, 04005
Numerical modelling of T-pipe joints forming
This paper presents results of numerical calculations of T-pipe joints (tee) forming process for a wide scope of industrial applications. FEM analyses were conducted for the chosen process technological parameters and tools designs. The kinematics of metal flow in the area of the formed flanges was analysed. Distributions of stresses, strains and damage criterion during forming were determined. Calculated values of forces and moments acting on tools and workpieces allow for designing of tools geometry for experimental verification of the proposed forming process.
- 18 September 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 190, 04005
Open AccessNumerical modelling of T-pipe joints forming
This paper presents results of numerical calculations of T-pipe joints (tee) forming process for a wide scope of industrial applications. FEM analyses were conducted for the chosen process technological parameters and tools designs. The kinematics of metal flow in the area of the formed flanges was analysed. Distributions of stresses, strains and damage criterion during forming were determined. Calculated values of forces and moments acting on tools and workpieces allow for designing of tools geometry for experimental verification of the proposed forming process.
- Open Access
- 1 November 2017
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 11,p. 982-984
Analysis of the extrusion process using a flexible tool
- 1 November 2017
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- No. 11,p. 982-984
Open AccessAnalysis of the extrusion process using a flexible tool
- Open Access
- 24 October 2016
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 80, 13004
Numerical analysis of bevel gear forming
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- 24 October 2016
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 80, 13004
Open AccessNumerical analysis of bevel gear forming
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry