Kevin D. Murphy
Research Subjects
Kevin D. Murphy has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
D. P. Almond
Institute for Complex Systems , University of Bath , Bath, England BA2 7AY
1 shared publicationEdward Z Moore
Department of Mechanical Engineering, University of Connecticut, Storrs, CT, USA
1 shared publicationG. W. Hunt
Institute for Complex Systems , University of Bath , Bath, England BA2 7AY
1 shared publicationJ.M. Nichols
Naval Research Laboratory, 4555 Overlook Avenue, Washington, DC 20375, USA
1 shared publicationJonathan M Nichols
Naval Research Laboratory, Washington, DC, USA
1 shared publication- Kazem Kazerounian
Department of Mechanical Engineering, University of Connecticut, Storrs, CT 06269
1 shared publication
Latest Publications
- 19 June 2013
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 135 (5) , 054502
Guided Tuning of Turbine Blades: A Practical Method to Avoid Operating at Resonance
In gas turbine applications, forced vibrations of turbine blades under resonant—or nearly resonant—conditions are undesirable. Usually in airfoil design procedures, at least the first three blade modes are required to be free of excitation in the operating speed range. However, not uncommonly, a blade may experience resonance at other higher natural frequencies. In an attempt to avoid resonant oscillations, the structural frequencies are tuned away from the excitation frequencies by changing the geometry of the blade. The typical iterative design process—of adding and removing material through restacking the airfoil sections—is laborious and in no way assures an optimal design. In response to the need for an effective and fast methodology, the guided tuning of turbine blades method (GTTB) is developed and presented in this paper. A practical tuning technique, the GTTB method is based on structural perturbations to the mass and stiffness at critical locations, as determined by the methodology described herein. This shifts the excited natural frequency out of the operating speed range, while leaving the other structural frequencies largely undisturbed. The methodology is demonstrated here in the redesign of an actual turbine blade. The numerical results are experimentally validated using a laser vibrometer. The results indicate that the proposed method is not computationally intensive and renders effective results that jibe with experiments.
- 19 June 2013
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 135 (5) , 054502
Guided Tuning of Turbine Blades: A Practical Method to Avoid Operating at Resonance
In gas turbine applications, forced vibrations of turbine blades under resonant—or nearly resonant—conditions are undesirable. Usually in airfoil design procedures, at least the first three blade modes are required to be free of excitation in the operating speed range. However, not uncommonly, a blade may experience resonance at other higher natural frequencies. In an attempt to avoid resonant oscillations, the structural frequencies are tuned away from the excitation frequencies by changing the geometry of the blade. The typical iterative design process—of adding and removing material through restacking the airfoil sections—is laborious and in no way assures an optimal design. In response to the need for an effective and fast methodology, the guided tuning of turbine blades method (GTTB) is developed and presented in this paper. A practical tuning technique, the GTTB method is based on structural perturbations to the mass and stiffness at critical locations, as determined by the methodology described herein. This shifts the excited natural frequency out of the operating speed range, while leaving the other structural frequencies largely undisturbed. The methodology is demonstrated here in the redesign of an actual turbine blade. The numerical results are experimentally validated using a laser vibrometer. The results indicate that the proposed method is not computationally intensive and renders effective results that jibe with experiments.
- 12 March 2013
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 12 (3) , 197-206
Optimized sensor placement for damage parameter estimation: Experimental results for a cracked plate
In this article, the optimum sensor and impact locations, for use in a damage identification experiment, are obtained using a hybrid genetic algorithm/steepest descent optimization method. Specifically, data from these optimum locations are used to identify the location, orientation, and size of a crack (termed the crack parameters) in a rectangular plate. The strain gage locations and orientations were selected in order (a) to maximize the difference between the model signal for a healthy plate and the model signal for a randomly damaged plate and (b) to minimize the cross-correlation among the signals measured by each of the gages. The latter requirement, in a sense, maximizes the uniqueness of the information measured from each sensor. The Bayesian model-based structural health monitoring identification technique, used to assess the crack parameters, was previously shown to be successful even for arbitrary sensor location/orientation and excitation location. It is shown here that thoughtful (optimized) sensor and excitation locations allow for improved estimates of the crack parameters. However, there is no substantial change in the width of the confidence intervals associated with these estimates.
- 12 March 2013
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 12 (3) , 197-206
Optimized sensor placement for damage parameter estimation: Experimental results for a cracked plate
In this article, the optimum sensor and impact locations, for use in a damage identification experiment, are obtained using a hybrid genetic algorithm/steepest descent optimization method. Specifically, data from these optimum locations are used to identify the location, orientation, and size of a crack (termed the crack parameters) in a rectangular plate. The strain gage locations and orientations were selected in order (a) to maximize the difference between the model signal for a healthy plate and the model signal for a randomly damaged plate and (b) to minimize the cross-correlation among the signals measured by each of the gages. The latter requirement, in a sense, maximizes the uniqueness of the information measured from each sensor. The Bayesian model-based structural health monitoring identification technique, used to assess the crack parameters, was previously shown to be successful even for arbitrary sensor location/orientation and excitation location. It is shown here that thoughtful (optimized) sensor and excitation locations allow for improved estimates of the crack parameters. However, there is no substantial change in the width of the confidence intervals associated with these estimates.
- Open Access
- 1 December 2012
- Published by Wiley in American Journal of Botany
- Vol. 99 (12) , 1918-1929
A physics‐based link model for tree vibrations
• Premise of the study: A new mathematical model for the vibration of trees is presented for developing a more thorough understanding of the underlying structure of the response. It may be used, for example, to assess the stability of a tree or to interpret experimental data.• Methods: A model is developed for the motion of the trunk and its N number of branches. The spatial distribution and initial orientation of the branches are left for the user to prescribe. A Newtonian analysis yields (N + 1) nonlinear, coupled differential equations that, when solved, describe the response of the trunk and each branch. After the model is linearized near equilibrium, the natural frequencies and vibration mode shapes are found. Closed‐form expressions for the response (i.e., the actual time histories) are then obtained using modal analysis. Numerical solutions are also found; these are used to validate the analytical solutions and to serve as a means for considering large amplitude vibrations.• Key results: A new physics‐based model is described. For small motion, the tree response may be constructed from the individual mode shapes and frequencies. Also demonstrated are the limitations of the linear theory as well as numerical solutions that can be obtained when trunk/branch amplitudes are large.• Conclusions: The model presented here incorporates critical physics into a model that describes tree vibrations. It also sheds light on the underlying structure of the vibration response in terms of the modal nature of the solution. Limitations to the linear solutions are demonstrated and discussed.
- 1 December 2012
- Published by Wiley in American Journal of Botany
- Vol. 99 (12) , 1918-1929
Open AccessA physics‐based link model for tree vibrations
• Premise of the study: A new mathematical model for the vibration of trees is presented for developing a more thorough understanding of the underlying structure of the response. It may be used, for example, to assess the stability of a tree or to interpret experimental data.• Methods: A model is developed for the motion of the trunk and its N number of branches. The spatial distribution and initial orientation of the branches are left for the user to prescribe. A Newtonian analysis yields (N + 1) nonlinear, coupled differential equations that, when solved, describe the response of the trunk and each branch. After the model is linearized near equilibrium, the natural frequencies and vibration mode shapes are found. Closed‐form expressions for the response (i.e., the actual time histories) are then obtained using modal analysis. Numerical solutions are also found; these are used to validate the analytical solutions and to serve as a means for considering large amplitude vibrations.• Key results: A new physics‐based model is described. For small motion, the tree response may be constructed from the individual mode shapes and frequencies. Also demonstrated are the limitations of the linear theory as well as numerical solutions that can be obtained when trunk/branch amplitudes are large.• Conclusions: The model presented here incorporates critical physics into a model that describes tree vibrations. It also sheds light on the underlying structure of the vibration response in terms of the modal nature of the solution. Limitations to the linear solutions are demonstrated and discussed.
- 5 November 2009
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 60 (3) , 327-339
Impact dynamics of MEMS switches
- 5 November 2009
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 60 (3) , 327-339
Impact dynamics of MEMS switches
- 28 August 2008
- Published by Elsevier in International Journal of Non-Linear Mechanics
- Vol. 44 (1) , 13-18
A low-dimensional model for delamination in a laterally loaded composite beam: Theory and experiment
- 28 August 2008
- Published by Elsevier in International Journal of Non-Linear Mechanics
- Vol. 44 (1) , 13-18
A low-dimensional model for delamination in a laterally loaded composite beam: Theory and experiment
- 21 July 2006
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 86 (21-22) , 3325-3338
Evidence of emergent scaling in mechanical systems
In previous work, electrical networks of randomly distributed resistors and capacitors driven with a periodic voltage have shown emergent scaling behaviour: a logarithmic scaling rule is found to dictate the conductance of the bulk network as a function of frequency. This feature has also been shown in other bi-materials and is thought to be independent of the materials involved and, hence, “universal” in nature. The present article examines the potential universality of these scaling laws by considering a mechanically loaded random network. In particular, the mechanical network under consideration is a statically loaded truss. The mechanical system shows an emergent region and percolation paths, much like its electrical counterpart, further suggesting that random, networked systems may have a universal character.
- 21 July 2006
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 86 (21-22) , 3325-3338
Evidence of emergent scaling in mechanical systems
In previous work, electrical networks of randomly distributed resistors and capacitors driven with a periodic voltage have shown emergent scaling behaviour: a logarithmic scaling rule is found to dictate the conductance of the bulk network as a function of frequency. This feature has also been shown in other bi-materials and is thought to be independent of the materials involved and, hence, “universal” in nature. The present article examines the potential universality of these scaling laws by considering a mechanically loaded random network. In particular, the mechanical network under consideration is a statically loaded truss. The mechanical system shows an emergent region and percolation paths, much like its electrical counterpart, further suggesting that random, networked systems may have a universal character.