Ronaldo Carvalho Battista
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ronaldo Carvalho Battista has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Michèle Schubert Pfeil
Universidade Federal do Rio de Janeiro, Brazil
3 shared publications - Alfredo Quiroga Flores
Civil Engineering program, Instituto Alberto Luiz Coimbra de Pós-Graduação e Pesquisa em Engenharia, Universidade Federal do Rio de Janeiro, Centro de Tecnologia, Rio de Janeiro, Brazil
1 shared publication - C. E. Rossigali
Universidade Federal do Rio de Janeiro, Brasil
1 shared publication - Joaquim Antonio Oliveira Barros
ISISE, ARISE, Department of Civil Engineering University of Minho Guimarães Portugal
1 shared publication - Luis Volnei Sudati Sagrilo
Laboratory of Analysis and Reliability of Offshore Structures, Civil Engineering Program (PEC), Alberto Luiz Coimbra Institute for Graduate Studies and Research in Engineering, Federal University of Rio de Janeiro, Rio de Janeiro 21941-598, Brazil
1 shared publication - Olga Maria Oliveira de Araujo
Nuclear Instrumentation Laboratory Federal University of Rio de Janeiro Rio de Janeiro Brazil
1 shared publication
Latest Publications
- Open Access
Relation between Shear Stresses and Flexural Tensile Stresses from Standardized Tests of Extracted Prismatic Specimens of an SFRC Bridge Girder
Experimental research on the direct shear behavior of fiber-reinforced concrete is often carried out using prisms molded with specific dimensions for a standardized test. However, the flow of fresh concrete in these molds can be different than in the case of a full-scale structural element. This is important considering that the flow direction highly influences the distribution and orientation of fibers. In addition, most of the studies did not relate their shear results to other mechanical properties. In contrast, this study attempted to deepen the experimental knowledge of the crack propagation of a steel fiber-reinforced concrete (SFRC) used in a full-scale prototype of a bridge box girder built in the laboratory. Prismatic specimens were sawn from webs and top flanges of this prototype. Serving as references, additional specimens were molded in wooden boxes. In a previous study of our research group, both had been tested under a three-point notched bending configuration maintaining test conditions proportional to the EN14651 specifications. From each of the previously flexurally tested specimens, two prismatic specimens suitable for the Fédération Internationale de la Précontrainte (FIP) shear test setup were extracted by adopting a cutting methodology that avoided the damage induced by the flexural tests to be part of the FIP specimens. These FIP specimens were tested in almost pure shear loading conditions for assessing the performance of SFRC. Computer tomography images and photos of the shear failure faces were used to determine the distribution and density of fibers. The results demonstrated that the peak loads were proportional to the fiber density at the shear failure section. Assuming that the SFRC conditions of the webs were representative of a common batching procedure in the construction industry, the results from the tests in specimens extracted from these webs were adopted to establish shear stress/flexural tensile stress ratios vs. crack mouth opening displacement curves. The curves belonging to cross-sections of a similar fiber density in the shear and flexural cases allowed for the proposal of a normalized crack-dilatancy relation composed of three stages of the crack propagation. In addition, a trilinear crack width–slip relation was established using the same set of specimens. The relevancy of this proposal is that the shear response can be estimated from a widely accepted standardized flexural test, which demands a simpler instrumentation and is also easier to execute than the shear setup.
Open AccessRelation between Shear Stresses and Flexural Tensile Stresses from Standardized Tests of Extracted Prismatic Specimens of an SFRC Bridge Girder
Experimental research on the direct shear behavior of fiber-reinforced concrete is often carried out using prisms molded with specific dimensions for a standardized test. However, the flow of fresh concrete in these molds can be different than in the case of a full-scale structural element. This is important considering that the flow direction highly influences the distribution and orientation of fibers. In addition, most of the studies did not relate their shear results to other mechanical properties. In contrast, this study attempted to deepen the experimental knowledge of the crack propagation of a steel fiber-reinforced concrete (SFRC) used in a full-scale prototype of a bridge box girder built in the laboratory. Prismatic specimens were sawn from webs and top flanges of this prototype. Serving as references, additional specimens were molded in wooden boxes. In a previous study of our research group, both had been tested under a three-point notched bending configuration maintaining test conditions proportional to the EN14651 specifications. From each of the previously flexurally tested specimens, two prismatic specimens suitable for the Fédération Internationale de la Précontrainte (FIP) shear test setup were extracted by adopting a cutting methodology that avoided the damage induced by the flexural tests to be part of the FIP specimens. These FIP specimens were tested in almost pure shear loading conditions for assessing the performance of SFRC. Computer tomography images and photos of the shear failure faces were used to determine the distribution and density of fibers. The results demonstrated that the peak loads were proportional to the fiber density at the shear failure section. Assuming that the SFRC conditions of the webs were representative of a common batching procedure in the construction industry, the results from the tests in specimens extracted from these webs were adopted to establish shear stress/flexural tensile stress ratios vs. crack mouth opening displacement curves. The curves belonging to cross-sections of a similar fiber density in the shear and flexural cases allowed for the proposal of a normalized crack-dilatancy relation composed of three stages of the crack propagation. In addition, a trilinear crack width–slip relation was established using the same set of specimens. The relevancy of this proposal is that the shear response can be estimated from a widely accepted standardized flexural test, which demands a simpler instrumentation and is also easier to execute than the shear setup.
- Open Access
- 1 April 2015
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 8 (2) , 124-139
Towards actual brazilian traffic load models for short span highway bridges
New live load models for highway bridge design in Brazil are under development by assembling real traffic database, traffic simulations, analytical-numerical modeling of the dynamic interaction between vehicle and structure and statistical extrapolations. This paper presents and discusses the results obtained in the first stages of this work which includes the comparison between the static effects due to the actual traffic of heavy vehicles and those generated by the live load model given in the current national code NBR 7188. It is demonstrated that this live load model is not appropriate to represent the actual traffic effects and may be, in some cases, non-conservative. The present work deals with short span bridges for two lanes single carriageway under free flow traffic scenarios. The representative static effects in these bridges due to the actual traffic of heavy vehicles are obtained by extrapolating its probability density functions to a certain return period. To this purpose, a traffic database was constructed by gathering data from several weighing stations in Brazilian highways which was then applied to perform traffic simulations through a specially developed computational tool.
- 1 April 2015
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 8 (2) , 124-139
Open AccessTowards actual brazilian traffic load models for short span highway bridges
New live load models for highway bridge design in Brazil are under development by assembling real traffic database, traffic simulations, analytical-numerical modeling of the dynamic interaction between vehicle and structure and statistical extrapolations. This paper presents and discusses the results obtained in the first stages of this work which includes the comparison between the static effects due to the actual traffic of heavy vehicles and those generated by the live load model given in the current national code NBR 7188. It is demonstrated that this live load model is not appropriate to represent the actual traffic effects and may be, in some cases, non-conservative. The present work deals with short span bridges for two lanes single carriageway under free flow traffic scenarios. The representative static effects in these bridges due to the actual traffic of heavy vehicles are obtained by extrapolating its probability density functions to a certain return period. To this purpose, a traffic database was constructed by gathering data from several weighing stations in Brazilian highways which was then applied to perform traffic simulations through a specially developed computational tool.
- Open Access
- 1 June 2007
- Published by FapUNIFESP (SciELO) in Rem: Revista Escola de Minas
- Vol. 60 (2) , 401-408
Estimativa da vida útil à fadiga de uma torre metálica sob ação do vento
A monitoração de uma torre metálica, típica do setor de telecomunicações, sob ação de ventos de baixa velocidade, registrou significativas oscilações e alertou para o risco de iniciação de fraturas em detalhes de ligações soldadas. O comportamento estrutural foi analisado a partir dos registros experimentais de aceleração e deformação, além de velocidade e direção do vento. Esse trabalho apresenta os resultados mais relevantes da monitoração dinâmica e a estimativa de vida útil à fadiga de detalhes de ligações soldadas efetuada por meio da regra de Palgrem-Miner, utilizando-se o algoritmo "rainflow" para contagem do número de ciclos. Para aumentar a reduzida vida útil encontrada nessa estimativa e para atenuar as oscilações da torre, foi projetado e instalado um sistema de controle dinâmico pendular, o qual teve sua eficiência demonstrada.
- 1 June 2007
- Published by FapUNIFESP (SciELO) in Rem: Revista Escola de Minas
- Vol. 60 (2) , 401-408
Open AccessEstimativa da vida útil à fadiga de uma torre metálica sob ação do vento
A monitoração de uma torre metálica, típica do setor de telecomunicações, sob ação de ventos de baixa velocidade, registrou significativas oscilações e alertou para o risco de iniciação de fraturas em detalhes de ligações soldadas. O comportamento estrutural foi analisado a partir dos registros experimentais de aceleração e deformação, além de velocidade e direção do vento. Esse trabalho apresenta os resultados mais relevantes da monitoração dinâmica e a estimativa de vida útil à fadiga de detalhes de ligações soldadas efetuada por meio da regra de Palgrem-Miner, utilizando-se o algoritmo "rainflow" para contagem do número de ciclos. Para aumentar a reduzida vida útil encontrada nessa estimativa e para atenuar as oscilações da torre, foi projetado e instalado um sistema de controle dinâmico pendular, o qual teve sua eficiência demonstrada.