Michèle Schubert Pfeil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Michèle Schubert Pfeil has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Luis Volnei Sudati Sagrilo
Laboratory of Analysis and Reliability of Offshore Structures, Civil Engineering Program (PEC), Alberto Luiz Coimbra Institute for Graduate Studies and Research in Engineering, Federal University of Rio de Janeiro, Rio de Janeiro 21941-598, Brazil
3 shared publications - Ronaldo Carvalho Battista
Civil Engineering Department, COPPE, Universidade Federal do Rio de Janeiro, Rio de Janeiro 21941-972, Brazil
3 shared publications - Wendell Diniz Varela
FAU / COPPE / UFRJ
3 shared publications - Carlos Eduardo Rossigali
Universidade Federal do Paraná, Brazil
2 shared publications - Ricardo Tadeu Lopes
Federal University of Rio de Janeiro, Rio de Janeiro, Brazil
2 shared publications - Romildo Dias Toledo Filho
Universidade Federal do Rio de Janeiro
2 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 23 (8)
Assessment of Brazilian highway bridge live load models on five girders decks under free flow and traffic jam conditions
The design of Brazilian highway bridges is based on the NBR 7188 code, which prescribes a live load model consisting of a 450 kN truck load and a distributed load of 5 kN/m2, both affected by an impact factor. Previous studies have shown that this load pattern does not adequately reproduce the effects of the real traffic. Two alternative load models that are more appropriate to represent actual Brazilian traffic effects were recently proposed; both were calibrated considering two-girder deck bridges, with span lengths up to 40 m. In such cases, the critical effects are associated with the free flow of heavy vehicles, including dynamic effects. This paper presents the procedures developed to assess the applicability of the previously proposed load models to five-girder bridges, with spans lengths ranging from 30 m to 50 m. For this span range, traffic jam scenarios are included in the analyses. The results indicate that the NBR 7188 load model is unsafe in several situations. Furthermore, one of the load models previously proposed was found to satisfactorily reproduce the effects of real traffic for this new set of bridges.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 23 (8)
Open AccessAssessment of Brazilian highway bridge live load models on five girders decks under free flow and traffic jam conditions
The design of Brazilian highway bridges is based on the NBR 7188 code, which prescribes a live load model consisting of a 450 kN truck load and a distributed load of 5 kN/m2, both affected by an impact factor. Previous studies have shown that this load pattern does not adequately reproduce the effects of the real traffic. Two alternative load models that are more appropriate to represent actual Brazilian traffic effects were recently proposed; both were calibrated considering two-girder deck bridges, with span lengths up to 40 m. In such cases, the critical effects are associated with the free flow of heavy vehicles, including dynamic effects. This paper presents the procedures developed to assess the applicability of the previously proposed load models to five-girder bridges, with spans lengths ranging from 30 m to 50 m. For this span range, traffic jam scenarios are included in the analyses. The results indicate that the NBR 7188 load model is unsafe in several situations. Furthermore, one of the load models previously proposed was found to satisfactorily reproduce the effects of real traffic for this new set of bridges.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 22 (1) , e8033
Assessment of reinforcements for enhancing structural performance of cold-formed steel polygonal conical poles for antennas support
The objective of this research is to present practical solutions for improving structural performance of thin-walled conic polygonal monopoles. The analysis encompasses computational simulations, analytical evaluation, and structural verification of reinforcements for openings and longitudinal folded stiffeners of flat walls. A benchmarked solution is derived from a design involving a 20-sided cold-formed steel polygonal section employed to support telecommunication antennas at a height of 40 meters. The structural verification is performed under the influence of wind loads, with particular attention to the commonly reported basic gust wind speed in Brazil. The conducted analysis encompasses: (i) wind-induced static equivalent dynamic behavior, (ii) parametric elastic buckling analysis, (iii) non-linear finite element analysis of reinforced openings, and (iv) direct strength method (DSM) performance evaluation of stiffened polygonal cross-sections. The importance of combining tailored numerical tools such as the finite strip and finite element methods, as well as wind-induced behavior, is demonstrated through the structural analysis results. In essence, the study's findings reveal the previously overlooked local-distortional buckling interaction in current design guidelines. Moreover, the research demonstrates that incorporating reinforcements and longitudinal stiffeners significantly enhances the flexural capacity of slender structures. Notably, the adoption of a single 4-fold (trapezoid) stiffener shape, per polygonal wall, emerges as a promising effective solution for enhancing the overall flexural capacity. Further full scale experimental structural tests and computational fluid dynamics should be considered for advanced structural analysis and improved design.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 22 (1) , e8033
Open AccessAssessment of reinforcements for enhancing structural performance of cold-formed steel polygonal conical poles for antennas support
The objective of this research is to present practical solutions for improving structural performance of thin-walled conic polygonal monopoles. The analysis encompasses computational simulations, analytical evaluation, and structural verification of reinforcements for openings and longitudinal folded stiffeners of flat walls. A benchmarked solution is derived from a design involving a 20-sided cold-formed steel polygonal section employed to support telecommunication antennas at a height of 40 meters. The structural verification is performed under the influence of wind loads, with particular attention to the commonly reported basic gust wind speed in Brazil. The conducted analysis encompasses: (i) wind-induced static equivalent dynamic behavior, (ii) parametric elastic buckling analysis, (iii) non-linear finite element analysis of reinforced openings, and (iv) direct strength method (DSM) performance evaluation of stiffened polygonal cross-sections. The importance of combining tailored numerical tools such as the finite strip and finite element methods, as well as wind-induced behavior, is demonstrated through the structural analysis results. In essence, the study's findings reveal the previously overlooked local-distortional buckling interaction in current design guidelines. Moreover, the research demonstrates that incorporating reinforcements and longitudinal stiffeners significantly enhances the flexural capacity of slender structures. Notably, the adoption of a single 4-fold (trapezoid) stiffener shape, per polygonal wall, emerges as a promising effective solution for enhancing the overall flexural capacity. Further full scale experimental structural tests and computational fluid dynamics should be considered for advanced structural analysis and improved design.
- Open Access
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
Piecewise Dynamic Mode Decomposition of Fluid Flow Simulations
The computational simulation of fluid flows over structures still is a major research area in fluid mechanics. Because of the multiscale nature of many of the application models and consequent large amount of data, these simulations are computationally expensive, but can benefit from modern Reduced Order Models and data-driven methods. In this work, Dynamic Mode Decomposition (DMD) and its recent variation, Piecewise DMD (pDMD), are presented and compared in terms of dynamic modes extracted from the data, accuracy in reconstructing an approximation for the original dataset as a reduced order model and, most importantly, computational cost. The pDMD method is shown to be a variation of the traditional DMD that aims to improve and overcome some of the caveats of the standard version. This variation consists in decomposing the entire data into smaller datasets and applying a linear mapping independently on each one of these subsets instead of calculating a global linear fitting. Basically, it is an application of multiple DMD on small subsets instead one DMD over the whole data. Piecewise DMD is a simple and elegant idea that is based on the "divide and conquer" approach well known in the numerical analysis literature. Even though pDMD is new and should be carefully and extensively tested, it can be considered as a promising improvement over the standard DMD. The preliminary results presented in this work show how DMD can capture the dynamics and accurately reconstruct the simulation data and how pDMD can provide more accurate results when traditional DMD reaches its limitations, capture the specific dynamics of different stages of transient flows, and reduce the computational cost by 90% for a two-dimensional flow over a cylinder when compared to standard DMD. Future applications of Reduced Order Models using both DMD and pDMD include future state predictions, computationally cheap parametric simulations, and qualitative dynamic analysis of fluid flows.
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
Open AccessPiecewise Dynamic Mode Decomposition of Fluid Flow Simulations
The computational simulation of fluid flows over structures still is a major research area in fluid mechanics. Because of the multiscale nature of many of the application models and consequent large amount of data, these simulations are computationally expensive, but can benefit from modern Reduced Order Models and data-driven methods. In this work, Dynamic Mode Decomposition (DMD) and its recent variation, Piecewise DMD (pDMD), are presented and compared in terms of dynamic modes extracted from the data, accuracy in reconstructing an approximation for the original dataset as a reduced order model and, most importantly, computational cost. The pDMD method is shown to be a variation of the traditional DMD that aims to improve and overcome some of the caveats of the standard version. This variation consists in decomposing the entire data into smaller datasets and applying a linear mapping independently on each one of these subsets instead of calculating a global linear fitting. Basically, it is an application of multiple DMD on small subsets instead one DMD over the whole data. Piecewise DMD is a simple and elegant idea that is based on the "divide and conquer" approach well known in the numerical analysis literature. Even though pDMD is new and should be carefully and extensively tested, it can be considered as a promising improvement over the standard DMD. The preliminary results presented in this work show how DMD can capture the dynamics and accurately reconstruct the simulation data and how pDMD can provide more accurate results when traditional DMD reaches its limitations, capture the specific dynamics of different stages of transient flows, and reduce the computational cost by 90% for a two-dimensional flow over a cylinder when compared to standard DMD. Future applications of Reduced Order Models using both DMD and pDMD include future state predictions, computationally cheap parametric simulations, and qualitative dynamic analysis of fluid flows.
- Open Access
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
Parametric study of the apparent modal parameters of crowd-footbridge systems
The modal parameters of footbridges are time-variant as pedestrians walk along them, resulting in a new dynamic system comprising the isolated structure and the walking persons. This phenomenon is known as human-structure interaction (HSI) and is particularly significant for lightweight footbridges, where the effective damping ratio of the combined system is significantly higher than that of the isolated structure. This paper proposes an analytical-numerical approach to address the effects of HSI on the modal parameters of the coupled system. The effective damping ratios and natural frequency are determined by solving the eigenvalue problem of a two-degree-of-freedom mass-spring-damper system, with one degree of freedom representing the isolated structure and the other representing the equivalent model of the walking persons. The obtained results are compared with experimental measurements from the literature, illustrating the effectiveness of the proposed approach while also demonstrating its computational cost-effectiveness in comparison to existing methods.
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
Open AccessParametric study of the apparent modal parameters of crowd-footbridge systems
The modal parameters of footbridges are time-variant as pedestrians walk along them, resulting in a new dynamic system comprising the isolated structure and the walking persons. This phenomenon is known as human-structure interaction (HSI) and is particularly significant for lightweight footbridges, where the effective damping ratio of the combined system is significantly higher than that of the isolated structure. This paper proposes an analytical-numerical approach to address the effects of HSI on the modal parameters of the coupled system. The effective damping ratios and natural frequency are determined by solving the eigenvalue problem of a two-degree-of-freedom mass-spring-damper system, with one degree of freedom representing the isolated structure and the other representing the equivalent model of the walking persons. The obtained results are compared with experimental measurements from the literature, illustrating the effectiveness of the proposed approach while also demonstrating its computational cost-effectiveness in comparison to existing methods.
- Open Access
- 12 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 1032
Load Models Representative of Brazilian Actual Traffic in Girder-Type Short-Span Highway Bridges
The Brazilian code NBR 7188 for highway bridge design prescribes a live load model consisting of a 3-axle vehicle plus a uniform load, which are both affected by an impact factor when considering dynamic effects. It does not play out actual traffic static effects and may be, in some cases, non-conservative. This work presents two load model configurations developed by gathering a real traffic database, traffic simulations, modeling of the dynamic interaction between vehicles and structure, and statistical extrapolations. Proposed load models comprise dynamic effects and were calibrated for two-lane single carriageway bridges with span lengths up to 40 m under free-flowing traffic. The target values of the effects were compared to those generated by the new proposed load models, as well as by the Brazilian design load model. Adequacy of the proposed models is demonstrated; results show that the effects generated by the Brazilian design load model are underestimated in many cases, particularly for negative moments in cantilevers.
- 12 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 1032
Open AccessLoad Models Representative of Brazilian Actual Traffic in Girder-Type Short-Span Highway Bridges
The Brazilian code NBR 7188 for highway bridge design prescribes a live load model consisting of a 3-axle vehicle plus a uniform load, which are both affected by an impact factor when considering dynamic effects. It does not play out actual traffic static effects and may be, in some cases, non-conservative. This work presents two load model configurations developed by gathering a real traffic database, traffic simulations, modeling of the dynamic interaction between vehicles and structure, and statistical extrapolations. Proposed load models comprise dynamic effects and were calibrated for two-lane single carriageway bridges with span lengths up to 40 m under free-flowing traffic. The target values of the effects were compared to those generated by the new proposed load models, as well as by the Brazilian design load model. Adequacy of the proposed models is demonstrated; results show that the effects generated by the Brazilian design load model are underestimated in many cases, particularly for negative moments in cantilevers.
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 16 (4)
A climatology-based wind speed map for NBR 6123
Updating the basic wind speed map of NBR 6123 –-Wind loading on buildings – is one of the duties of the committee responsible for the revision of this code. Traditionally such maps are elaborated by means of extreme value wind speed data collected at meteorological stations, use of statistical methods for data characterization, and application of mathematical regression to elaborate the territorial maps. However, the spatial distribution of the atmospheric phenomena responsible for strong winds cannot be disregarded. This work presents a proposal for a new wind speed map for NBR 6123 combining a climatological approach and wind speed data recently compiled from hundreds of meteorological stations. A climatological wind map was first produced considering the phenomena which cause strong winds, and used as a basis to draw the isopleths of the basic wind speed map, considering the measured wind speed data. The resulting map shows basic wind speeds ranging from 30 to 48m/s.
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 16 (4)
Open AccessA climatology-based wind speed map for NBR 6123
Updating the basic wind speed map of NBR 6123 –-Wind loading on buildings – is one of the duties of the committee responsible for the revision of this code. Traditionally such maps are elaborated by means of extreme value wind speed data collected at meteorological stations, use of statistical methods for data characterization, and application of mathematical regression to elaborate the territorial maps. However, the spatial distribution of the atmospheric phenomena responsible for strong winds cannot be disregarded. This work presents a proposal for a new wind speed map for NBR 6123 combining a climatological approach and wind speed data recently compiled from hundreds of meteorological stations. A climatological wind map was first produced considering the phenomena which cause strong winds, and used as a basis to draw the isopleths of the basic wind speed map, considering the measured wind speed data. The resulting map shows basic wind speeds ranging from 30 to 48m/s.
- Open Access
Relation between Shear Stresses and Flexural Tensile Stresses from Standardized Tests of Extracted Prismatic Specimens of an SFRC Bridge Girder
Experimental research on the direct shear behavior of fiber-reinforced concrete is often carried out using prisms molded with specific dimensions for a standardized test. However, the flow of fresh concrete in these molds can be different than in the case of a full-scale structural element. This is important considering that the flow direction highly influences the distribution and orientation of fibers. In addition, most of the studies did not relate their shear results to other mechanical properties. In contrast, this study attempted to deepen the experimental knowledge of the crack propagation of a steel fiber-reinforced concrete (SFRC) used in a full-scale prototype of a bridge box girder built in the laboratory. Prismatic specimens were sawn from webs and top flanges of this prototype. Serving as references, additional specimens were molded in wooden boxes. In a previous study of our research group, both had been tested under a three-point notched bending configuration maintaining test conditions proportional to the EN14651 specifications. From each of the previously flexurally tested specimens, two prismatic specimens suitable for the Fédération Internationale de la Précontrainte (FIP) shear test setup were extracted by adopting a cutting methodology that avoided the damage induced by the flexural tests to be part of the FIP specimens. These FIP specimens were tested in almost pure shear loading conditions for assessing the performance of SFRC. Computer tomography images and photos of the shear failure faces were used to determine the distribution and density of fibers. The results demonstrated that the peak loads were proportional to the fiber density at the shear failure section. Assuming that the SFRC conditions of the webs were representative of a common batching procedure in the construction industry, the results from the tests in specimens extracted from these webs were adopted to establish shear stress/flexural tensile stress ratios vs. crack mouth opening displacement curves. The curves belonging to cross-sections of a similar fiber density in the shear and flexural cases allowed for the proposal of a normalized crack-dilatancy relation composed of three stages of the crack propagation. In addition, a trilinear crack width–slip relation was established using the same set of specimens. The relevancy of this proposal is that the shear response can be estimated from a widely accepted standardized flexural test, which demands a simpler instrumentation and is also easier to execute than the shear setup.
Open AccessRelation between Shear Stresses and Flexural Tensile Stresses from Standardized Tests of Extracted Prismatic Specimens of an SFRC Bridge Girder
Experimental research on the direct shear behavior of fiber-reinforced concrete is often carried out using prisms molded with specific dimensions for a standardized test. However, the flow of fresh concrete in these molds can be different than in the case of a full-scale structural element. This is important considering that the flow direction highly influences the distribution and orientation of fibers. In addition, most of the studies did not relate their shear results to other mechanical properties. In contrast, this study attempted to deepen the experimental knowledge of the crack propagation of a steel fiber-reinforced concrete (SFRC) used in a full-scale prototype of a bridge box girder built in the laboratory. Prismatic specimens were sawn from webs and top flanges of this prototype. Serving as references, additional specimens were molded in wooden boxes. In a previous study of our research group, both had been tested under a three-point notched bending configuration maintaining test conditions proportional to the EN14651 specifications. From each of the previously flexurally tested specimens, two prismatic specimens suitable for the Fédération Internationale de la Précontrainte (FIP) shear test setup were extracted by adopting a cutting methodology that avoided the damage induced by the flexural tests to be part of the FIP specimens. These FIP specimens were tested in almost pure shear loading conditions for assessing the performance of SFRC. Computer tomography images and photos of the shear failure faces were used to determine the distribution and density of fibers. The results demonstrated that the peak loads were proportional to the fiber density at the shear failure section. Assuming that the SFRC conditions of the webs were representative of a common batching procedure in the construction industry, the results from the tests in specimens extracted from these webs were adopted to establish shear stress/flexural tensile stress ratios vs. crack mouth opening displacement curves. The curves belonging to cross-sections of a similar fiber density in the shear and flexural cases allowed for the proposal of a normalized crack-dilatancy relation composed of three stages of the crack propagation. In addition, a trilinear crack width–slip relation was established using the same set of specimens. The relevancy of this proposal is that the shear response can be estimated from a widely accepted standardized flexural test, which demands a simpler instrumentation and is also easier to execute than the shear setup.
- 26 February 2020
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 8 (6) , 883-892
Experimental Investigation on Human Walking Loading Parameters and Biodynamic Model
- 26 February 2020
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 8 (6) , 883-892
Experimental Investigation on Human Walking Loading Parameters and Biodynamic Model
- Open Access
- 1 October 2015
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 8 (5) , 707-720
3D investigation of steel fiber distribution in reinforced concrete by X-ray microtomography
The effects of the inclusion of steel fibers in concrete have been widely studied in order to investigate possible changes in mechanical properties, such as the increase in tensile strength, ductility, stiffness, toughness (energy absorption capacity), and durability. An immediate consequence of this addition is the mitigation of concrete's brittle behavior, so that the material meets new quality requirements. In this context, it is important to study the spatial distribution of the entire internal structure of these materials. Three-dimensional computed microtomography is a non-destructive inspection technique used to characterize the internal structures of various materials based on X-ray interaction with the inspected object. Topological and morphological properties can be obtained directly in three dimensions by means of mathematical reconstruction of the radiographs, which allows analyzing, for example, porosity and distribution of objects. In this context, the aim of this study is to investigate the spatial distribution of steel fibers, as well as of porosity in reinforced concrete samples. To this end, we used a microtomography system calibrated to operate at a voltage of 80 kV, electric current of 100 μA and a pixel size equal to 24 µm. The results showed low porosity and that the steel fibers were not uniformly distributed throughout the sample.
- 1 October 2015
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 8 (5) , 707-720
Open Access3D investigation of steel fiber distribution in reinforced concrete by X-ray microtomography
The effects of the inclusion of steel fibers in concrete have been widely studied in order to investigate possible changes in mechanical properties, such as the increase in tensile strength, ductility, stiffness, toughness (energy absorption capacity), and durability. An immediate consequence of this addition is the mitigation of concrete's brittle behavior, so that the material meets new quality requirements. In this context, it is important to study the spatial distribution of the entire internal structure of these materials. Three-dimensional computed microtomography is a non-destructive inspection technique used to characterize the internal structures of various materials based on X-ray interaction with the inspected object. Topological and morphological properties can be obtained directly in three dimensions by means of mathematical reconstruction of the radiographs, which allows analyzing, for example, porosity and distribution of objects. In this context, the aim of this study is to investigate the spatial distribution of steel fibers, as well as of porosity in reinforced concrete samples. To this end, we used a microtomography system calibrated to operate at a voltage of 80 kV, electric current of 100 μA and a pixel size equal to 24 µm. The results showed low porosity and that the steel fibers were not uniformly distributed throughout the sample.
- Open Access
- 1 April 2015
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 8 (2) , 124-139
Towards actual brazilian traffic load models for short span highway bridges
New live load models for highway bridge design in Brazil are under development by assembling real traffic database, traffic simulations, analytical-numerical modeling of the dynamic interaction between vehicle and structure and statistical extrapolations. This paper presents and discusses the results obtained in the first stages of this work which includes the comparison between the static effects due to the actual traffic of heavy vehicles and those generated by the live load model given in the current national code NBR 7188. It is demonstrated that this live load model is not appropriate to represent the actual traffic effects and may be, in some cases, non-conservative. The present work deals with short span bridges for two lanes single carriageway under free flow traffic scenarios. The representative static effects in these bridges due to the actual traffic of heavy vehicles are obtained by extrapolating its probability density functions to a certain return period. To this purpose, a traffic database was constructed by gathering data from several weighing stations in Brazilian highways which was then applied to perform traffic simulations through a specially developed computational tool.
- 1 April 2015
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 8 (2) , 124-139
Open AccessTowards actual brazilian traffic load models for short span highway bridges
New live load models for highway bridge design in Brazil are under development by assembling real traffic database, traffic simulations, analytical-numerical modeling of the dynamic interaction between vehicle and structure and statistical extrapolations. This paper presents and discusses the results obtained in the first stages of this work which includes the comparison between the static effects due to the actual traffic of heavy vehicles and those generated by the live load model given in the current national code NBR 7188. It is demonstrated that this live load model is not appropriate to represent the actual traffic effects and may be, in some cases, non-conservative. The present work deals with short span bridges for two lanes single carriageway under free flow traffic scenarios. The representative static effects in these bridges due to the actual traffic of heavy vehicles are obtained by extrapolating its probability density functions to a certain return period. To this purpose, a traffic database was constructed by gathering data from several weighing stations in Brazilian highways which was then applied to perform traffic simulations through a specially developed computational tool.