Ahmet Umut Güler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ahmet Umut Güler has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Gözlem Ceylan
Ondokuz Mayıs University
4 shared publications- Ali Çagin Yücel
Department of Restorative Dentistry, Ondokuz Mayis University, Faculty of Dentistry, Samsun, Turkey
3 shared publications Ibrahim Duran
3 shared publicationsSafak Kurt
Research Assistant, Department of Prosthodontics
3 shared publicationsPelin Özkan
Ankara University
2 shared publicationsTolga Kulunk
Research Assistant, Department of Prosthodontics
2 shared publications
Latest Publications
- 1 January 2012
- Vol. 43 (1) , e1-8
Effects of different acids and etching times on the bond strength of glass fiber-reinforced composite root canal posts to composite core material.
To investigate the effects of different acids and etching times on the bond strength of glass fiber-reinforced composite (FRC) posts to composite core material. Twenty-six FRC posts (FRC Postec Plus) were randomly divided into 13 groups (each n = 2). One group received no surface treatment (control). The posts in the other groups were acid etched with 35% phosphoric acid and 5% and 9.6% hydrofluoric acid gel for four different etching times (30, 60, 120, and 180 seconds). A cylindric polytetrafluoroethylene mold was placed around the treated posts and filled with dual-cure composite core material (MultiCore Flow). All samples were light cured for 60 seconds. After 24 hours of water storage, the specimens were sectioned perpendicularly to the bonded interface under water cooling to obtain 2-mm post-and-core specimens. Eight specimens were made from each group. Push-out tests were performed at a crosshead speed of 0.5 mm/min using a universal testing machine. Data were analyzed by one-way ANOVA followed by the Tukey honestly significant difference test (alpha = .05). The lowest bond strength was observed in the control group (12.51 megapascal [MPa]). No statistical significant difference was observed among group H5-120 (20.31 MPa), group H9-120 (20.55 MPa), or group P-180 (20.57 MPa) (P > .05). These groups demonstrated the highest bond strength values (P < .05). For the FRC posts, all acid-etching procedures tested showed significantly increased bond strength when compared with the control group. Acid-etching with 5% hydrofluoric acid and 9.6% hydrofluoric acid for 2 minutes and with 35% phosphoric acid for 3 minutes (groups H5-120, H9-120, and P-180, respectively) demonstrated the highest bond strength values between the FRC post and composite core material. Although the bond strength was increased by prolonged acid etching, the microstructure of the FRC posts might have been damaged.
- 1 January 2012
- Vol. 43 (1) , e1-8
Effects of different acids and etching times on the bond strength of glass fiber-reinforced composite root canal posts to composite core material.
To investigate the effects of different acids and etching times on the bond strength of glass fiber-reinforced composite (FRC) posts to composite core material. Twenty-six FRC posts (FRC Postec Plus) were randomly divided into 13 groups (each n = 2). One group received no surface treatment (control). The posts in the other groups were acid etched with 35% phosphoric acid and 5% and 9.6% hydrofluoric acid gel for four different etching times (30, 60, 120, and 180 seconds). A cylindric polytetrafluoroethylene mold was placed around the treated posts and filled with dual-cure composite core material (MultiCore Flow). All samples were light cured for 60 seconds. After 24 hours of water storage, the specimens were sectioned perpendicularly to the bonded interface under water cooling to obtain 2-mm post-and-core specimens. Eight specimens were made from each group. Push-out tests were performed at a crosshead speed of 0.5 mm/min using a universal testing machine. Data were analyzed by one-way ANOVA followed by the Tukey honestly significant difference test (alpha = .05). The lowest bond strength was observed in the control group (12.51 megapascal [MPa]). No statistical significant difference was observed among group H5-120 (20.31 MPa), group H9-120 (20.55 MPa), or group P-180 (20.57 MPa) (P > .05). These groups demonstrated the highest bond strength values (P < .05). For the FRC posts, all acid-etching procedures tested showed significantly increased bond strength when compared with the control group. Acid-etching with 5% hydrofluoric acid and 9.6% hydrofluoric acid for 2 minutes and with 35% phosphoric acid for 3 minutes (groups H5-120, H9-120, and P-180, respectively) demonstrated the highest bond strength values between the FRC post and composite core material. Although the bond strength was increased by prolonged acid etching, the microstructure of the FRC posts might have been damaged.
- Open Access
- 22 July 2011
- Published by FapUNIFESP (SciELO) in Journal of Applied Oral Science
- Vol. 19 (5) , 505-510
Effects of air-polishing powders on color stability of composite resins
The purpose of this study was to investigate the effect of different air-polishing powders on the color stability of different types of composite resin restorative materials. Thirty cylindrical specimens (15×2 mm) were prepared for each of 7 composite resin restorative materials. All specimens were polished with a series of aluminum oxide polishing discs (Sof-Lex). The prepared specimens of each composite resin were randomly divided into 3 groups of 10 specimens each, for control (Group-C) and two air-powder applications (Group-CP: Cavitron Prophy-Jet; Group-PS: Sirona ProSmile prophylaxis powder). A standard air-polishing unit (ProSmile Handly) was used. All specimens were air-powdered for 10 s at 4-bar pressure. The distance of the spray nosel from the specimens was approximately 10 mm and angulation of the nosel was 90º. Specimens were stored in 100 mL of coffee (Nescafe Classic) for 24 h at 37ºC. Color measurement of all specimens was recorded before and after exposure to staining agent with a colorimeter (Minolta CR-300). Color differences (∆E*) between the 2 color measurements (baseline and after 24 h storage) were calculated. The data were analyzed with a 2-way ANOVA test, and mean values were compared by the Tukey HSD test (p≤0.05). According to the 2-way ANOVA results, composite resin restorative materials, air-polishing powders, and their interaction were statistically significant (p.05) and these groups demonstrated the highest ∆E* values. For Filtek Silorane and IntenS, the highest ∆E* values were observed in Group-PS. The lowest ∆E* values for all composite resin groups were observed in Group-C. When comparing the 7 composite resin restorative materials, Aelite Aesthetic Enemal demonstrated significantly less ∆E* values than the other composite resins tested. The highest ∆E* values were observed in Quixfil. Except for Quixfil, all control groups of composite resins that were polished Sof-Lex exhibited clinically acceptable ∆E values (<3.7). Air-polishing applications increased the color change for all composite resin restorative materials tested. Composite restorations may require re-polishing after air-polishing.
- 22 July 2011
- Published by FapUNIFESP (SciELO) in Journal of Applied Oral Science
- Vol. 19 (5) , 505-510
Open AccessEffects of air-polishing powders on color stability of composite resins
The purpose of this study was to investigate the effect of different air-polishing powders on the color stability of different types of composite resin restorative materials. Thirty cylindrical specimens (15×2 mm) were prepared for each of 7 composite resin restorative materials. All specimens were polished with a series of aluminum oxide polishing discs (Sof-Lex). The prepared specimens of each composite resin were randomly divided into 3 groups of 10 specimens each, for control (Group-C) and two air-powder applications (Group-CP: Cavitron Prophy-Jet; Group-PS: Sirona ProSmile prophylaxis powder). A standard air-polishing unit (ProSmile Handly) was used. All specimens were air-powdered for 10 s at 4-bar pressure. The distance of the spray nosel from the specimens was approximately 10 mm and angulation of the nosel was 90º. Specimens were stored in 100 mL of coffee (Nescafe Classic) for 24 h at 37ºC. Color measurement of all specimens was recorded before and after exposure to staining agent with a colorimeter (Minolta CR-300). Color differences (∆E*) between the 2 color measurements (baseline and after 24 h storage) were calculated. The data were analyzed with a 2-way ANOVA test, and mean values were compared by the Tukey HSD test (p≤0.05). According to the 2-way ANOVA results, composite resin restorative materials, air-polishing powders, and their interaction were statistically significant (p.05) and these groups demonstrated the highest ∆E* values. For Filtek Silorane and IntenS, the highest ∆E* values were observed in Group-PS. The lowest ∆E* values for all composite resin groups were observed in Group-C. When comparing the 7 composite resin restorative materials, Aelite Aesthetic Enemal demonstrated significantly less ∆E* values than the other composite resins tested. The highest ∆E* values were observed in Quixfil. Except for Quixfil, all control groups of composite resins that were polished Sof-Lex exhibited clinically acceptable ∆E values (<3.7). Air-polishing applications increased the color change for all composite resin restorative materials tested. Composite restorations may require re-polishing after air-polishing.
- 7 April 2011
- Published by Wiley in Journal of Esthetic and Restorative Dentistry
- Vol. 23 (2) , 89-95
Alternative Treatment Procedure in the Case of Fractured Abutment of Adhesive Bridge: A Clinical Report
In this case report, an alternative approach was presented for treatment of coronal fracture including pulp of maxillary central incisor, one of the abutments of an adhesive bridge, by using fiber post and tooth's own fractured component. The patient was referred to our clinic with the complaint of pain from the upper right central incisor and mobility of the adhesive bridge in maxillary anterior segment. It was realized that, the upper right central incisor, one of the abutments of the adhesive bridge, had been fractured at middle thirds of the crown including the pulp chamber. After dismounting the adhesive bridge and completion of the root canal treatment, a fiber post was placed into the fractured tooth. The fractured component, adherent to adhesive bridge retainer, was concorded to the fiber post. The whole structure was cemented with adhesive resin. A 1‐mm‐wide groove was made along the fracture line and restored with composite resin. The patient was evaluated clinically and radiographically at 12 and 30 months after the treatment.CLINICAL SIGNIFICANCE: Adhesive cementation of fractured component by supporting the remaining tooth structure with a fiber post is an inexpensive and conservative treatment alternative when the fractured component is compatible with the remaining tooth structure in cases of tooth fractures including the pulp chamber at anterior segment.(J Esthet Restor Dent 23:89–96, 2011)
- 7 April 2011
- Published by Wiley in Journal of Esthetic and Restorative Dentistry
- Vol. 23 (2) , 89-95
Alternative Treatment Procedure in the Case of Fractured Abutment of Adhesive Bridge: A Clinical Report
In this case report, an alternative approach was presented for treatment of coronal fracture including pulp of maxillary central incisor, one of the abutments of an adhesive bridge, by using fiber post and tooth's own fractured component. The patient was referred to our clinic with the complaint of pain from the upper right central incisor and mobility of the adhesive bridge in maxillary anterior segment. It was realized that, the upper right central incisor, one of the abutments of the adhesive bridge, had been fractured at middle thirds of the crown including the pulp chamber. After dismounting the adhesive bridge and completion of the root canal treatment, a fiber post was placed into the fractured tooth. The fractured component, adherent to adhesive bridge retainer, was concorded to the fiber post. The whole structure was cemented with adhesive resin. A 1‐mm‐wide groove was made along the fracture line and restored with composite resin. The patient was evaluated clinically and radiographically at 12 and 30 months after the treatment.CLINICAL SIGNIFICANCE: Adhesive cementation of fractured component by supporting the remaining tooth structure with a fiber post is an inexpensive and conservative treatment alternative when the fractured component is compatible with the remaining tooth structure in cases of tooth fractures including the pulp chamber at anterior segment.(J Esthet Restor Dent 23:89–96, 2011)
- 20 October 2010
- Published by Springer Nature in Lasers in Medical Science
- Vol. 27 (1) , 47-51
Effects of Er:YAG laser treatments on surface roughness of base metal alloys
We investigated the effects of different Er:YAG laser treatments on the surface roughness of base metal alloys. A total of 36 specimens were prepared of two base metal alloys (Wiron 99, Bellabond plus). The surfaces of the specimens were standardized by gradual wet grinding with 320-, 600-, 800- and 1,000-grit silicon carbide paper for 10 s each on a grinding machine at 300 rpm. Specimens of each alloy were randomly divided into six groups (n = 6) comprising a control group (group C), a group sandblasted with Al2O3 powder at 60 psi for 10 s through a nozzle at a distance of 10 mm (group S), and four Er:YAG laser (Fotona AT) treatment groups. The laser treatment groups were as follows: 500 mJ, 10 Hz, 100 μs (group 500MSP); 500 mJ, 10 Hz, 300 μs (group 500SP); 400 mJ, 10 Hz, 100 μs (group 400MSP); and 400 mJ, 10 Hz, 300 μs (group 400SP). Surface roughness measurements (Ra) were performed using a profilometer. The data were analysed by two-way ANOVA, and mean values were compared using Tukey’s HSD test (α = 0.05). According to the two-way ANOVA results, the base metal alloys and interaction between base metal alloy and surface treatment were not statistically significant different (p > 0.05), the surface treatments were significantly different (p < 0.0001). For the two base metal alloy groups, no significant differences were observed among the control, 400MSP, and 400SP groups (p = 0.912), and these groups demonstrated the lowest Ra values. The highest Ra value was observed in group S (p < 0.05). Er:YAG laser treatment at 400 and 500 mJ/10 Hz is not an alternative method for surface roughening of base metal alloys.
- 20 October 2010
- Published by Springer Nature in Lasers in Medical Science
- Vol. 27 (1) , 47-51
Effects of Er:YAG laser treatments on surface roughness of base metal alloys
We investigated the effects of different Er:YAG laser treatments on the surface roughness of base metal alloys. A total of 36 specimens were prepared of two base metal alloys (Wiron 99, Bellabond plus). The surfaces of the specimens were standardized by gradual wet grinding with 320-, 600-, 800- and 1,000-grit silicon carbide paper for 10 s each on a grinding machine at 300 rpm. Specimens of each alloy were randomly divided into six groups (n = 6) comprising a control group (group C), a group sandblasted with Al2O3 powder at 60 psi for 10 s through a nozzle at a distance of 10 mm (group S), and four Er:YAG laser (Fotona AT) treatment groups. The laser treatment groups were as follows: 500 mJ, 10 Hz, 100 μs (group 500MSP); 500 mJ, 10 Hz, 300 μs (group 500SP); 400 mJ, 10 Hz, 100 μs (group 400MSP); and 400 mJ, 10 Hz, 300 μs (group 400SP). Surface roughness measurements (Ra) were performed using a profilometer. The data were analysed by two-way ANOVA, and mean values were compared using Tukey’s HSD test (α = 0.05). According to the two-way ANOVA results, the base metal alloys and interaction between base metal alloy and surface treatment were not statistically significant different (p > 0.05), the surface treatments were significantly different (p < 0.0001). For the two base metal alloy groups, no significant differences were observed among the control, 400MSP, and 400SP groups (p = 0.912), and these groups demonstrated the lowest Ra values. The highest Ra value was observed in group S (p < 0.05). Er:YAG laser treatment at 400 and 500 mJ/10 Hz is not an alternative method for surface roughening of base metal alloys.
- 30 September 2010
- Published by Elsevier in Journal of Dental Sciences
- Vol. 5 (3) , 136-143
Effects of air polishing powders on the surface roughness of composite resins
- 30 September 2010
- Published by Elsevier in Journal of Dental Sciences
- Vol. 5 (3) , 136-143
Effects of air polishing powders on the surface roughness of composite resins
- 1 May 2009
- Published by Operative Dentistry in Operative Dentistry
- Vol. 34 (3) , 299-305
Effect of Filler Ratio in Adhesive Systems on the Shear Bond Strength of Resin Composite to Porcelains
Clinical Relevance: The results of this study indicate that adhesive systems with a high filler ratio provide the greatest strength for resin repair of low-fusing feldspathic porcelain restorations. In addition, self-etching adhesive systems may not be indicated for such repairs.
- 1 May 2009
- Published by Operative Dentistry in Operative Dentistry
- Vol. 34 (3) , 299-305
Effect of Filler Ratio in Adhesive Systems on the Shear Bond Strength of Resin Composite to Porcelains
Clinical Relevance: The results of this study indicate that adhesive systems with a high filler ratio provide the greatest strength for resin repair of low-fusing feldspathic porcelain restorations. In addition, self-etching adhesive systems may not be indicated for such repairs.
- 19 August 2007
- Vol. 38 (7) , e399-403
Panoramic radiographic examination of edentulous mouths.
Panoramic radiographs often are the first method used to screen edentulous patients before complete denture therapy. However, routine radiographic examination of edentulous patients is being questioned because of the cumulative effects and cost of radiation exposure. The purpose of this study was to determine the frequency and location of significant radiographic findings in edentulous jaws. Panoramic radiographs from 338 patients were included in the survey (183 men, 155 women; 676 edentulous arches). The radiographs were evaluated by 1 oral radiology specialist for the following clinically significant radiographic findings: retained root fragments, impacted teeth, radiolucencies associated with cysts, radiopacities associated with localized sclerotic bone formation, location of the mental foramen on the crest, and location of the maxillary sinus close to the crest of the ridge. The data were analyzed using descriptive statistics. Radiographic findings were found in 47.6% (56.5% women, 43.5% men) of the edentulous patients. Fifty-two subjects (29 women, 23 men) had 67 submucosal or intrabony root remains, 50 of which were located in the maxilla. The most frequent finding was retained root fragment, followed by radiopacities. Impacted teeth were found in 11 women and 10 men. In 15 patients the mental foramen was situated at the top of the residual ridge. Of these patients, 13 were women and 2 were men. In 29 patients (14 women, 15 men) the maxillary sinus was close to the crest of the ridge. Six patients (3 women, 3 men) had a bilateral maxillary sinus close to the crest of the ridge. The other 23 patients had a unilateral maxillary sinus close to the crest of the ridge, and except for in 2 men, all were in the left side of the maxilla. Routine panoramic examination of the jaws is necessary to detect impacted teeth, retained root fragments, and other radiographic findings that may require treatment before construction of complete dentures.
- 19 August 2007
- Vol. 38 (7) , e399-403
Panoramic radiographic examination of edentulous mouths.
Panoramic radiographs often are the first method used to screen edentulous patients before complete denture therapy. However, routine radiographic examination of edentulous patients is being questioned because of the cumulative effects and cost of radiation exposure. The purpose of this study was to determine the frequency and location of significant radiographic findings in edentulous jaws. Panoramic radiographs from 338 patients were included in the survey (183 men, 155 women; 676 edentulous arches). The radiographs were evaluated by 1 oral radiology specialist for the following clinically significant radiographic findings: retained root fragments, impacted teeth, radiolucencies associated with cysts, radiopacities associated with localized sclerotic bone formation, location of the mental foramen on the crest, and location of the maxillary sinus close to the crest of the ridge. The data were analyzed using descriptive statistics. Radiographic findings were found in 47.6% (56.5% women, 43.5% men) of the edentulous patients. Fifty-two subjects (29 women, 23 men) had 67 submucosal or intrabony root remains, 50 of which were located in the maxilla. The most frequent finding was retained root fragment, followed by radiopacities. Impacted teeth were found in 11 women and 10 men. In 15 patients the mental foramen was situated at the top of the residual ridge. Of these patients, 13 were women and 2 were men. In 29 patients (14 women, 15 men) the maxillary sinus was close to the crest of the ridge. Six patients (3 women, 3 men) had a bilateral maxillary sinus close to the crest of the ridge. The other 23 patients had a unilateral maxillary sinus close to the crest of the ridge, and except for in 2 men, all were in the left side of the maxilla. Routine panoramic examination of the jaws is necessary to detect impacted teeth, retained root fragments, and other radiographic findings that may require treatment before construction of complete dentures.
- 1 March 2006
- Vol. 18 (2) , 103-4
Color stability of provisional restorations.
- 12 September 2005
- Published by Wiley in Journal of Oral Rehabilitation
- Vol. 32 (10) , 741-746
The evaluation of vertical heights of maxillary and mandibular bones and the location of anatomic landmarks in panoramic radiographs of edentulous patients for implant dentistry
summary The purpose of this study was to determine variations in the vertical height measurements in the edentulous maxilla and mandible, and to assess positions of the maxillary sinus, mandibular foramen, and the mandibular canal, which are important for implant length selection and planning using panoramic radiographs. The study sample included 346 edentulous alveolar ridges of 90 men and 83 women. Sixty‐three dentate patients’ panoramic radiographs were used for location of the first premolar and molar area. Panoramic radiographs were made with a Siemens Orthophos panoramic machine which had been standardized previously. All radiographs were made using a standardized manner by the same technician. Fourteen sites were measured on every panoramic radiograph whenever possible, eight sites in the maxilla and six sites in the mandible. Correlation analyses were performed between age groups and all measurements to determine if age is significant as a covariate. In order to examine the effect of gender the statistical analysis of differences between men and women was performed with Student t‐test. The 5% significance level was used for statistical significancy. The height of the maxilla and the mandible in the anterior, first premolar, and first molar regions were significantly greater in men than in women. A majority of the most inferior border of the maxillary sinuses was located anterior to the first molar area (premolar regions) both in men (48·9%) and women (55·4%). Although, there was no statistically significant difference between edentulous men and women for the vertical distances from the mental foramen to the alveolar crest, and horizontal distances from mental foramen to midline, there were statistically significant differences between edentulous men and edentulous women for the vertical distances from the upper border of the mandibular canal to the alveolar crest in the first molar area. Mental foramens were located at the crest of the ridge in 7·2% of the edentulous women, and 6·7% of the edentulous men. The results of this study may guide clinicians to make primer decision of implant insertion area for implant supported prosthesis in edentulous patients.
- 12 September 2005
- Published by Wiley in Journal of Oral Rehabilitation
- Vol. 32 (10) , 741-746
The evaluation of vertical heights of maxillary and mandibular bones and the location of anatomic landmarks in panoramic radiographs of edentulous patients for implant dentistry
summary The purpose of this study was to determine variations in the vertical height measurements in the edentulous maxilla and mandible, and to assess positions of the maxillary sinus, mandibular foramen, and the mandibular canal, which are important for implant length selection and planning using panoramic radiographs. The study sample included 346 edentulous alveolar ridges of 90 men and 83 women. Sixty‐three dentate patients’ panoramic radiographs were used for location of the first premolar and molar area. Panoramic radiographs were made with a Siemens Orthophos panoramic machine which had been standardized previously. All radiographs were made using a standardized manner by the same technician. Fourteen sites were measured on every panoramic radiograph whenever possible, eight sites in the maxilla and six sites in the mandible. Correlation analyses were performed between age groups and all measurements to determine if age is significant as a covariate. In order to examine the effect of gender the statistical analysis of differences between men and women was performed with Student t‐test. The 5% significance level was used for statistical significancy. The height of the maxilla and the mandible in the anterior, first premolar, and first molar regions were significantly greater in men than in women. A majority of the most inferior border of the maxillary sinuses was located anterior to the first molar area (premolar regions) both in men (48·9%) and women (55·4%). Although, there was no statistically significant difference between edentulous men and women for the vertical distances from the mental foramen to the alveolar crest, and horizontal distances from mental foramen to midline, there were statistically significant differences between edentulous men and edentulous women for the vertical distances from the upper border of the mandibular canal to the alveolar crest in the first molar area. Mental foramens were located at the crest of the ridge in 7·2% of the edentulous women, and 6·7% of the edentulous men. The results of this study may guide clinicians to make primer decision of implant insertion area for implant supported prosthesis in edentulous patients.
- Top Cited Papers
- 1 August 2005
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 94 (2) , 118-124
Effects of different drinks on stainability of resin composite provisional restorative materials
- 1 August 2005
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 94 (2) , 118-124
Top Cited PapersEffects of different drinks on stainability of resin composite provisional restorative materials