Alexander Wiedermann
Research Subjects
Alexander Wiedermann has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Milan V. Petrovic
University of Belgrade—Faculty of Mechanical Engineering, 11120 Belgrade, Serbia
5 shared publications - Milan Banjac
Faculty of Mechanical Engineering, University of Belgrade, Belgrade 11120, Serbia
3 shared publications - Martin Bohle
Associated Fellow) Max Weber Centre for Advanced Cultural and Social Studies
2 shared publications - Kenichiro Takeishi
Tokushima Bunri University
1 shared publication M. B. Banjac
University of Belgrade
1 shared publication- M. Cagna
MAN Diesel & Turbo SE, Oberhausen, Germany
1 shared publication
Latest Publications
- 19 December 2018
- Published by Springer Nature
- p. 67-71
Aeroderivate
- 19 December 2018
- Published by Springer Nature
- p. 1-8
Gasturbinentypen – eine Übersicht
- 1 May 2015
- Published by Wiley in Journal of Turbomachinery
- Vol. 137 (5) , 051004
Secondary Flows, Endwall Effects, and Stall Detection in Axial Compressor Design
This paper describes a methodology and a fully tested and calibrated mathematical model for the treatment of endwall effects in axial compressor aerodynamic calculations. Additional losses and deviations caused by the clearance and secondary flows are analyzed. These effects are coupled with endwall boundary layer losses (EWBL) and blockage development. Stall/surge detection is included, and mutual interaction of different loss mechanisms is considered. Individual mathematical correlations for different effects have been created or adopted from earlier papers with the aim of forming one integral model that is completely described in this paper. Separate mathematical correlations and calibration measures are discussed in detail in the first part of the paper. The developed overall model is suitable for application in two-dimensional (2D) or mean-line compressor flow calculations. During the development, it was tested, calibrated, and validated using throughflow calculations comparing numerical results with experimental data for a large number of test cases. These test cases include compressors with very different configurations and operating ranges. The data on the compressors were taken from the open literature or obtained from industrial partners.
- 1 May 2015
- Published by Wiley in Journal of Turbomachinery
- Vol. 137 (5) , 051004
Secondary Flows, Endwall Effects, and Stall Detection in Axial Compressor Design
This paper describes a methodology and a fully tested and calibrated mathematical model for the treatment of endwall effects in axial compressor aerodynamic calculations. Additional losses and deviations caused by the clearance and secondary flows are analyzed. These effects are coupled with endwall boundary layer losses (EWBL) and blockage development. Stall/surge detection is included, and mutual interaction of different loss mechanisms is considered. Individual mathematical correlations for different effects have been created or adopted from earlier papers with the aim of forming one integral model that is completely described in this paper. Separate mathematical correlations and calibration measures are discussed in detail in the first part of the paper. The developed overall model is suitable for application in two-dimensional (2D) or mean-line compressor flow calculations. During the development, it was tested, calibrated, and validated using throughflow calculations comparing numerical results with experimental data for a large number of test cases. These test cases include compressors with very different configurations and operating ranges. The data on the compressors were taken from the open literature or obtained from industrial partners.
- 2 January 2014
- Published by Wiley in Journal of Turbomachinery
- Vol. 136 (7) , 071011
A New Loss and Deviation Model for Axial Compressor Inlet Guide Vanes
This paper describes a new universal algebraic model for the estimation of flow deflection and losses in axial compressor inlet guide vane devices. The model deals with nominal flow and far-off-design operating conditions in connection with large stagger angle adjustments. The first part of the model considers deflection and losses in 2D cascades, taking into account the main cascade geometry parameters and operating conditions, such as Mach number and stagger adjustment. The second part of the model deals with additional deviation and losses due to secondary flow caused by the end wall viscous effects and by the trailing vortices. The model is developed for NACA65 airfoils, NACA63-A4K6 airfoils, and airfoils having an NACA65 thickness distribution on a circular-arc camber line. It is suitable for application in 1D or 2D through-flow calculations for design and analysis cases. The development of the method is based on systematic computational fluid dynamics (CFD) flow calculations for various cascade geometries and operating parameters. The comparison of correlation results with experimental data for several test cases shows good agreement.
- 2 January 2014
- Published by Wiley in Journal of Turbomachinery
- Vol. 136 (7) , 071011
A New Loss and Deviation Model for Axial Compressor Inlet Guide Vanes
This paper describes a new universal algebraic model for the estimation of flow deflection and losses in axial compressor inlet guide vane devices. The model deals with nominal flow and far-off-design operating conditions in connection with large stagger angle adjustments. The first part of the model considers deflection and losses in 2D cascades, taking into account the main cascade geometry parameters and operating conditions, such as Mach number and stagger adjustment. The second part of the model deals with additional deviation and losses due to secondary flow caused by the end wall viscous effects and by the trailing vortices. The model is developed for NACA65 airfoils, NACA63-A4K6 airfoils, and airfoils having an NACA65 thickness distribution on a circular-arc camber line. It is suitable for application in 1D or 2D through-flow calculations for design and analysis cases. The development of the method is based on systematic computational fluid dynamics (CFD) flow calculations for various cascade geometries and operating parameters. The comparison of correlation results with experimental data for several test cases shows good agreement.
- 13 September 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 135 (6) , 061019
Through-Flow Analysis of Air-Cooled Gas Turbines
This paper describes the development of a new through-flow method for the analysis of axial multistage turbines with cooling by air from compressor bleed. The method is based on a stream function approach and a finite element solution procedure. It includes a high-fidelity loss and deviation model with improved correlations. A radial distribution model of losses and a new spanwise mixing model are applied to simulate 3D flow effects. The calibration of the models is performed by calculation of a number of test cases with different configurations, with the aim of achieving high accuracy and optimum robustness for each of the test cases considered. Various types of cooling air injection were encompassed: film cooling, trailing edge injection, and disk/endwall coolant flow. There are two effects of air cooling: (i) increase in mass flow downstream of the injection surface and (ii) reduction of the gas total temperature connected with total pressure losses. For both of these effects, the appropriate 2D models were developed and applied. The code was applied to flow analysis and performance prediction of a newly developed industrial gas turbine. Comparison of the predicted results and measured test data for a number of parameters showed good agreement. The results of the validation confirmed that this method based on calibrated correlations can be considered a reliable tool for flow analysis and parameter variation during the design phase.
- 13 September 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 135 (6) , 061019
Through-Flow Analysis of Air-Cooled Gas Turbines
This paper describes the development of a new through-flow method for the analysis of axial multistage turbines with cooling by air from compressor bleed. The method is based on a stream function approach and a finite element solution procedure. It includes a high-fidelity loss and deviation model with improved correlations. A radial distribution model of losses and a new spanwise mixing model are applied to simulate 3D flow effects. The calibration of the models is performed by calculation of a number of test cases with different configurations, with the aim of achieving high accuracy and optimum robustness for each of the test cases considered. Various types of cooling air injection were encompassed: film cooling, trailing edge injection, and disk/endwall coolant flow. There are two effects of air cooling: (i) increase in mass flow downstream of the injection surface and (ii) reduction of the gas total temperature connected with total pressure losses. For both of these effects, the appropriate 2D models were developed and applied. The code was applied to flow analysis and performance prediction of a newly developed industrial gas turbine. Comparison of the predicted results and measured test data for a number of parameters showed good agreement. The results of the validation confirmed that this method based on calibrated correlations can be considered a reliable tool for flow analysis and parameter variation during the design phase.
- 29 April 2011
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 75 (2) , 45-60
Entwicklung eines neuen Meridionalverfahrens für mehrstufige kompakte Axialverdichter und Validierung durch Experimente und CFD-Berechnungen
- 29 April 2011
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 75 (2) , 45-60
Entwicklung eines neuen Meridionalverfahrens für mehrstufige kompakte Axialverdichter und Validierung durch Experimente und CFD-Berechnungen
- Open Access
- 1 January 2011
- Published by European Turbomachinery Society
Effect of turbulence modeling and mesh refinement on film cooling flow analysis
The film cooling effectiveness along a surface wetted by a hot gas is governed by the developing temperature boundary layer which is affected by turbulent mixing processes. If the film cooling effectiveness is to be estimated by numerical procedures, the real flow effects in the boundary layer must be taken into account. In this paper fundamental research has been carried out to find the best-suited turbulence model in combination with a proper resolution of the boundary layer with the objective of estimating film cooling effectiveness at lowest computational costs. The results are evaluated and verified with experimental data.
- 1 January 2011
- Published by European Turbomachinery Society
Open AccessEffect of turbulence modeling and mesh refinement on film cooling flow analysis
The film cooling effectiveness along a surface wetted by a hot gas is governed by the developing temperature boundary layer which is affected by turbulent mixing processes. If the film cooling effectiveness is to be estimated by numerical procedures, the real flow effects in the boundary layer must be taken into account. In this paper fundamental research has been carried out to find the best-suited turbulence model in combination with a proper resolution of the boundary layer with the objective of estimating film cooling effectiveness at lowest computational costs. The results are evaluated and verified with experimental data.
- Open Access
- 1 January 2011
- Published by European Turbomachinery Society
Stationary gas turbine intake design and its impact on a transonic compressor stage
In this paper, results of numerical flow simulations (CFD) of an intake geometry are presented and their impact on the first transonic stage (inlet guide vane, rotor, stator) of an industrial gas turbine is discussed. The aim is to achieve thorough understanding of the interaction between the intake flow and the first compressor stage and of the most important loss mechanisms as well. The inlet flow channel accelerates the flow from Ma = 0.1 to Ma = 0.6 by turning it from almost radial to the axial direction. It was found that for a well designed intake the predicted effects of inlet flow distortion on over-all compressor performance were small, with no significant changes in the pressure-ratio and efficiency decreasing then only slightly. The parameter studies indicate that further reduction of the axial length of the intake is tolerable to a certain extend but ultimately leads to a strong decrease in pressure ratio, efficiency and operational stability when the length is reduced below a critical value. Experimental results of the flow through the transonic compressor with and without inlet distortion are in very good accordance with CFD results.
- 1 January 2011
- Published by European Turbomachinery Society
Open AccessStationary gas turbine intake design and its impact on a transonic compressor stage
In this paper, results of numerical flow simulations (CFD) of an intake geometry are presented and their impact on the first transonic stage (inlet guide vane, rotor, stator) of an industrial gas turbine is discussed. The aim is to achieve thorough understanding of the interaction between the intake flow and the first compressor stage and of the most important loss mechanisms as well. The inlet flow channel accelerates the flow from Ma = 0.1 to Ma = 0.6 by turning it from almost radial to the axial direction. It was found that for a well designed intake the predicted effects of inlet flow distortion on over-all compressor performance were small, with no significant changes in the pressure-ratio and efficiency decreasing then only slightly. The parameter studies indicate that further reduction of the axial length of the intake is tolerable to a certain extend but ultimately leads to a strong decrease in pressure ratio, efficiency and operational stability when the length is reduced below a critical value. Experimental results of the flow through the transonic compressor with and without inlet distortion are in very good accordance with CFD results.
- 3 August 2010
- Published by Springer Nature
- p. 101-108
Aeroderivate
- 3 August 2010
- Published by Springer Nature
- p. 1-10
Gasturbinentypen - eine Übersicht