Mojmil Cecić
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mojmil Cecić has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ana Kuzmanić Skelin
Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture (FESB), University of Split, 21000 Split, Croatia
2 shared publications - Josip Musić
University of Split
2 shared publications - Ivo Stančić
Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture (FESB), University of Split, 21000 Split, Croatia
1 shared publication - Mario Miličević
Faculty of Maritime Studies, University of Split, 21000 Split, Croatia
1 shared publication - Mirjana Bonkovic
Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture (FESB), University of Split, 21000 Split, Croatia
1 shared publication - Vlasta Zanchi
University of Split
1 shared publication
Latest Publications
- Open Access
Self-Referential Generalized-Cylinder Fitting for Mast Deformation Measurement from UAV Point Clouds
Dimensional control of tall-ship masts is difficult: rigging occludes deck-based surveys, and registration to a design model assumes it matches the as-built structure. We present a deterministic, self-referential method that measures mast bending from an unmanned aerial vehicle (UAV) photogrammetric point cloud without a computer-aided design model. Each mast is modeled as a tapered generalized cylinder: slices are fitted with trimmed circles, flare and rigging-band slices are rejected, and an uncertainty-weighted centerline is split into rake and bending. A five-mast shared-curvature test provides a candidate bound on photogrammetric doming but is inconclusive here. On the Golden Horizon, the method recovers aft rakes of 1.2–1.9° and bends of 36–160 mm at wavelengths above 16 m. On matched synthetic clouds, assumed spatially correlated reconstruction error sets per-mast floors of 20–27 mm (mean) and 29–40 mm (90th percentile), against 7 mm under independent noise; UAV and terrestrial laser scanning (TLS) profiles have root-mean-square differences of 14–33 mm. Tested against straight synthetic masts, two masts bend significantly at the 5% level, but only the Foremast, which TLS could not check, stays significant under all fourteen error models and, under the default model, after a multiple-testing correction; the Mainmast, significant under eleven, agrees with TLS only transversely.
Open AccessSelf-Referential Generalized-Cylinder Fitting for Mast Deformation Measurement from UAV Point Clouds
Dimensional control of tall-ship masts is difficult: rigging occludes deck-based surveys, and registration to a design model assumes it matches the as-built structure. We present a deterministic, self-referential method that measures mast bending from an unmanned aerial vehicle (UAV) photogrammetric point cloud without a computer-aided design model. Each mast is modeled as a tapered generalized cylinder: slices are fitted with trimmed circles, flare and rigging-band slices are rejected, and an uncertainty-weighted centerline is split into rake and bending. A five-mast shared-curvature test provides a candidate bound on photogrammetric doming but is inconclusive here. On the Golden Horizon, the method recovers aft rakes of 1.2–1.9° and bends of 36–160 mm at wavelengths above 16 m. On matched synthetic clouds, assumed spatially correlated reconstruction error sets per-mast floors of 20–27 mm (mean) and 29–40 mm (90th percentile), against 7 mm under independent noise; UAV and terrestrial laser scanning (TLS) profiles have root-mean-square differences of 14–33 mm. Tested against straight synthetic masts, two masts bend significantly at the 5% level, but only the Foremast, which TLS could not check, stays significant under all fourteen error models and, under the default model, after a multiple-testing correction; the Mainmast, significant under eleven, agrees with TLS only transversely.
- Open Access
The Development of a Cost-Effective Imaging Device Based on Thermographic Technology
Thermal vision-based devices are nowadays used in a number of industries, ranging from the automotive industry, surveillance, navigation, fire detection, and rescue missions to precision agriculture. This work describes the development of a low-cost imaging device based on thermographic technology. The proposed device uses a miniature microbolometer module, a 32-bit ARM microcontroller, and a high-accuracy ambient temperature sensor. The developed device is capable of enhancing RAW high dynamic thermal readings obtained from the sensor using a computationally efficient image enhancement algorithm and presenting its visual result on the integrated OLED display. The choice of microcontroller, rather than the alternative System on Chip (SoC), offers almost instantaneous power uptime and extremely low power consumption while providing real-time imaging of an environment. The implemented image enhancement algorithm employs the modified histogram equalization, where the ambient temperature sensor helps the algorithm enhance both background objects near ambient temperature and foreground objects (humans, animals, and other heat sources) that actively emit heat. The proposed imaging device was evaluated on a number of environmental scenarios using standard no-reference image quality measures and comparisons against the existing state-of-the-art enhancement algorithms. Qualitative results obtained from the survey of 11 subjects are also provided. The quantitative evaluations show that, on average, images acquired by the developed camera provide better perception quality in 75% of tested cases. According to qualitative evaluations, images acquired by the developed camera provide better perception quality in 69% of tested cases. The obtained results verify the usability of the developed low-cost device for a range of applications where thermal imaging is needed.
Open AccessThe Development of a Cost-Effective Imaging Device Based on Thermographic Technology
Thermal vision-based devices are nowadays used in a number of industries, ranging from the automotive industry, surveillance, navigation, fire detection, and rescue missions to precision agriculture. This work describes the development of a low-cost imaging device based on thermographic technology. The proposed device uses a miniature microbolometer module, a 32-bit ARM microcontroller, and a high-accuracy ambient temperature sensor. The developed device is capable of enhancing RAW high dynamic thermal readings obtained from the sensor using a computationally efficient image enhancement algorithm and presenting its visual result on the integrated OLED display. The choice of microcontroller, rather than the alternative System on Chip (SoC), offers almost instantaneous power uptime and extremely low power consumption while providing real-time imaging of an environment. The implemented image enhancement algorithm employs the modified histogram equalization, where the ambient temperature sensor helps the algorithm enhance both background objects near ambient temperature and foreground objects (humans, animals, and other heat sources) that actively emit heat. The proposed imaging device was evaluated on a number of environmental scenarios using standard no-reference image quality measures and comparisons against the existing state-of-the-art enhancement algorithms. Qualitative results obtained from the survey of 11 subjects are also provided. The quantitative evaluations show that, on average, images acquired by the developed camera provide better perception quality in 75% of tested cases. According to qualitative evaluations, images acquired by the developed camera provide better perception quality in 69% of tested cases. The obtained results verify the usability of the developed low-cost device for a range of applications where thermal imaging is needed.
- Open Access
- 18 January 2010
- Published by Taylor & Francis in Automatika
- Vol. 51 (3) , 264-274
Real-Time Body Orientation Estimation Based on Two-Layer Stochastic Filter Architecture
The article presents real time rigid body orientation estimation using inertial and magnetic sensors. Based on the review of orientation estimation literature we suggest, as possible alternative to standard approaches, novel two-layer stochastic estimation filter architecture based on Kalman and particle filters combined into two layers. Two-layer architecture was chosen because it enables greater applicability via upgrade of already implemented Kalman or particle filters. Four two-layer filter architectures were designed, each one enabling different layer interaction. Estimation of human head orientation was chosen as a case example. Simulated data and batch head orientation measurement data were used to test the proposed architectures in terms of accuracy and computational efficiency and to select the best one in terms of aforementioned performance parameters. Selected architecture was then implemented in real time for human-computer interaction and was tested on several practical applications. Obtained results are presented and discussed and future research directions suggested.
- 18 January 2010
- Published by Taylor & Francis in Automatika
- Vol. 51 (3) , 264-274
Open AccessReal-Time Body Orientation Estimation Based on Two-Layer Stochastic Filter Architecture
The article presents real time rigid body orientation estimation using inertial and magnetic sensors. Based on the review of orientation estimation literature we suggest, as possible alternative to standard approaches, novel two-layer stochastic estimation filter architecture based on Kalman and particle filters combined into two layers. Two-layer architecture was chosen because it enables greater applicability via upgrade of already implemented Kalman or particle filters. Four two-layer filter architectures were designed, each one enabling different layer interaction. Estimation of human head orientation was chosen as a case example. Simulated data and batch head orientation measurement data were used to test the proposed architectures in terms of accuracy and computational efficiency and to select the best one in terms of aforementioned performance parameters. Selected architecture was then implemented in real time for human-computer interaction and was tested on several practical applications. Obtained results are presented and discussed and future research directions suggested.