Jonas Östh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jonas Östh has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Karin Brolin
Department of Mechanics and Maritime Sciences, Chalmers University of Technology, SE - 412 96, Gothenburg, Sweden
3 shared publications - Astrid Linder
Swedish National Road and Transport Research Institute, VTI, Gothenburg, Sweden
2 shared publications - Fusako Sato
Japan Automobile Research Institute
2 shared publications Karin Brolin
Department of Applied Mechanics , Chalmers University of Technology , Göteborg , Sweden
2 shared publications- Mats Y. Svensson
Chalmers University of Technology
2 shared publications - Riender Happee
Delft University of Technology
2 shared publications
Latest Publications
- Open Access
- 1 January 2017
- Published by Elsevier in Journal of Biomechanics
- Vol. 51, 49-56
A female head–neck model for rear impact simulations
- 1 January 2017
- Published by Elsevier in Journal of Biomechanics
- Vol. 51, 49-56
Open AccessA female head–neck model for rear impact simulations
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Bioengineering Conference Annual Meeting of BED/JSME
- Vol. 2017.29, 2E12
Differences of the spinal alignment between females and males in a driving posture and its effects on spinal kinematics in rear-end impact
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Bioengineering Conference Annual Meeting of BED/JSME
- Vol. 2017.29, 2E12
Differences of the spinal alignment between females and males in a driving posture and its effects on spinal kinematics in rear-end impact
- 2 May 2016
- Published by ASME International in Journal of Biomechanical Engineering
- Vol. 138 (6) , 061005
A Female Ligamentous Cervical Spine Finite Element Model Validated for Physiological Loads
Mathematical cervical spine models allow for studying of impact loading that can cause whiplash associated disorders (WAD). However, existing models only cover the male anthropometry, despite the female population being at a higher risk of sustaining WAD in automotive rear-end impacts. The aim of this study is to develop and validate a ligamentous cervical spine intended for biomechanical research on the effect of automotive impacts. A female model has the potential to aid the design of better protection systems as well as improve understanding of injury mechanisms causing WAD. A finite element (FE) mesh was created from surface data of the cervical vertebrae of a 26-year old female (stature 167 cm, weight 59 kg). Soft tissues were generated from the skeletal geometry and anatomical literature descriptions. Ligaments were modeled with nonlinear elastic orthotropic membrane elements, intervertebral disks as composites of nonlinear elastic bulk elements, and orthotropic anulus fibrosus fiber layers, while cortical and trabecular bones were modeled as isotropic plastic–elastic. The model has geometrical features representative of the female cervical spine—the largest average difference compared with published anthropometric female data was the vertebral body depth being 3.4% shorter for the model. The majority the cervical segments compare well with respect to biomechanical data at physiological loads, with the best match for flexion–extension loads and less biofidelity for axial rotation. An average female FE ligamentous cervical spine model was developed and validated with respect to physiological loading. In flexion–extension simulations with the developed female model and an existing average male cervical spine model, a greater range of motion (ROM) was found in the female model.
- 2 May 2016
- Published by ASME International in Journal of Biomechanical Engineering
- Vol. 138 (6) , 061005
A Female Ligamentous Cervical Spine Finite Element Model Validated for Physiological Loads
Mathematical cervical spine models allow for studying of impact loading that can cause whiplash associated disorders (WAD). However, existing models only cover the male anthropometry, despite the female population being at a higher risk of sustaining WAD in automotive rear-end impacts. The aim of this study is to develop and validate a ligamentous cervical spine intended for biomechanical research on the effect of automotive impacts. A female model has the potential to aid the design of better protection systems as well as improve understanding of injury mechanisms causing WAD. A finite element (FE) mesh was created from surface data of the cervical vertebrae of a 26-year old female (stature 167 cm, weight 59 kg). Soft tissues were generated from the skeletal geometry and anatomical literature descriptions. Ligaments were modeled with nonlinear elastic orthotropic membrane elements, intervertebral disks as composites of nonlinear elastic bulk elements, and orthotropic anulus fibrosus fiber layers, while cortical and trabecular bones were modeled as isotropic plastic–elastic. The model has geometrical features representative of the female cervical spine—the largest average difference compared with published anthropometric female data was the vertebral body depth being 3.4% shorter for the model. The majority the cervical segments compare well with respect to biomechanical data at physiological loads, with the best match for flexion–extension loads and less biofidelity for axial rotation. An average female FE ligamentous cervical spine model was developed and validated with respect to physiological loading. In flexion–extension simulations with the developed female model and an existing average male cervical spine model, a greater range of motion (ROM) was found in the female model.
- Open Access
- 1 September 2014
- Published by Elsevier in Gait & Posture
- Vol. 40 (4) , 664-669
A method to model anticipatory postural control in driver braking events
- 1 September 2014
- Published by Elsevier in Gait & Posture
- Vol. 40 (4) , 664-669
Open AccessA method to model anticipatory postural control in driver braking events
- 1 May 2012
- Published by Taylor & Francis in Traffic Injury Prevention
- Vol. 13 (3) , 265-277
The Occupant Response to Autonomous Braking: A Modeling Approach That Accounts for Active Musculature
Objective: The aim of this study is to model occupant kinematics in an autonomous braking event by using a finite element (FE) human body model (HBM) with active muscles as a step toward HBMs that can be used for injury prediction in integrated precrash and crash simulations. Methods: Trunk and neck musculature was added to an existing FE HBM. Active muscle responses were achieved using a simplified implementation of 3 feedback controllers for head angle, neck angle, and angle of the lumbar spine. The HBM was compared with volunteer responses in sled tests with 10 ms−2 deceleration over 0.2 s and in 1.4-s autonomous braking interventions with a peak deceleration of 6.7 ms−2. Results: The HBM captures the characteristics of the kinematics of volunteers in sled tests. Peak forward displacements have the same timing as for the volunteers, and lumbar muscle activation timing matches data from one of the volunteers. The responses of volunteers in autonomous braking interventions are mainly small head rotations and translational motions. This is captured by the HBM controller objective, which is to maintain the initial angular positions. The HBM response with active muscles is within ±1 standard deviation of the average volunteer response with respect to head displacements and angular rotation. Conclusions: With the implementation of feedback control of active musculature in an FE HBM it is possible to model the occupant response to autonomous braking interventions. The lumbar controller is important for the simulations of lap belt–restrained occupants; it is less important for the kinematics of occupants with a modern 3-point seat belt. Increasing head and neck controller gains provides a better correlation for head rotation, whereas it reduces the vertical head displacement and introduces oscillations.
- 1 May 2012
- Published by Taylor & Francis in Traffic Injury Prevention
- Vol. 13 (3) , 265-277
The Occupant Response to Autonomous Braking: A Modeling Approach That Accounts for Active Musculature
Objective: The aim of this study is to model occupant kinematics in an autonomous braking event by using a finite element (FE) human body model (HBM) with active muscles as a step toward HBMs that can be used for injury prediction in integrated precrash and crash simulations. Methods: Trunk and neck musculature was added to an existing FE HBM. Active muscle responses were achieved using a simplified implementation of 3 feedback controllers for head angle, neck angle, and angle of the lumbar spine. The HBM was compared with volunteer responses in sled tests with 10 ms−2 deceleration over 0.2 s and in 1.4-s autonomous braking interventions with a peak deceleration of 6.7 ms−2. Results: The HBM captures the characteristics of the kinematics of volunteers in sled tests. Peak forward displacements have the same timing as for the volunteers, and lumbar muscle activation timing matches data from one of the volunteers. The responses of volunteers in autonomous braking interventions are mainly small head rotations and translational motions. This is captured by the HBM controller objective, which is to maintain the initial angular positions. The HBM response with active muscles is within ±1 standard deviation of the average volunteer response with respect to head displacements and angular rotation. Conclusions: With the implementation of feedback control of active musculature in an FE HBM it is possible to model the occupant response to autonomous braking interventions. The lumbar controller is important for the simulations of lap belt–restrained occupants; it is less important for the kinematics of occupants with a modern 3-point seat belt. Increasing head and neck controller gains provides a better correlation for head rotation, whereas it reduces the vertical head displacement and introduces oscillations.
- 1 April 2012
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering
- Vol. 15 (4) , 347-361
Active muscle response using feedback control of a finite element human arm model
Mathematical human body models (HBMs) are important research tools that are used to study the human response in car crash situations. Development of automotive safety systems requires the implementation of active muscle response in HBM, as novel safety systems also interact with vehicle occupants in the pre-crash phase. In this study, active muscle response was implemented using feedback control of a nonlinear muscle model in the right upper extremity of a finite element (FE) HBM. Hill-type line muscle elements were added, and the active and passive properties were assessed. Volunteer tests with low impact loading resulting in elbow flexion motions were performed. Simulations of posture maintenance in a gravity field and the volunteer tests were successfully conducted. It was concluded that feedback control of a nonlinear musculoskeletal model can be used to obtain posture maintenance and human-like reflexive responses in an FE HBM.
- 1 April 2012
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering
- Vol. 15 (4) , 347-361
Active muscle response using feedback control of a finite element human arm model
Mathematical human body models (HBMs) are important research tools that are used to study the human response in car crash situations. Development of automotive safety systems requires the implementation of active muscle response in HBM, as novel safety systems also interact with vehicle occupants in the pre-crash phase. In this study, active muscle response was implemented using feedback control of a nonlinear muscle model in the right upper extremity of a finite element (FE) HBM. Hill-type line muscle elements were added, and the active and passive properties were assessed. Volunteer tests with low impact loading resulting in elbow flexion motions were performed. Simulations of posture maintenance in a gravity field and the volunteer tests were successfully conducted. It was concluded that feedback control of a nonlinear musculoskeletal model can be used to obtain posture maintenance and human-like reflexive responses in an FE HBM.