Éva Vázsonyi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Éva Vázsonyi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Anita Pongrácz
MTA EK MFA MEMS Laboratory, H-1083 Budapest, Hungary
1 shared publication - Bálint Péter Kerekes
Faculty of Information Technology and Bionics, Pázmány Péter University, Budapest, Hungary
1 shared publication - Csaba Dücső
Centre for Energy Research, HUN-REN, Budapest, Hungary
1 shared publication - Dorottya Gubán
Research Institute for Technical Physics and Materials Science, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest, Hungary
1 shared publication - Gergely Márton
Research Institute for Technical Physics and Materials Science, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest, Hungary
1 shared publication - György Karmos
Pázmány Péter Catholic University, Faculty of Information Technology, 50/A Práter u., H-1083 Budapest, Hungary
1 shared publication
Latest Publications
- 25 December 2010
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 166 (1) , 14-21
A novel multisite silicon probe for high quality laminar neural recordings
- 25 December 2010
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 166 (1) , 14-21
A novel multisite silicon probe for high quality laminar neural recordings
- Open Access
- 22 August 2007
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 17 (9) , 1916-1922
Characterization of the anisotropic etching of silicon in two-component alkaline solution
The characteristics of wet chemical etching processes were compared for crystalline Si in aqueous solutions of pure NaOH and NaOH with added oxidizing agent NaOCl (sodium-hypochlorite). Due to the addition of NaOCl to the reference NaOH solution, the etch rate decreased for the {1?0?0} and {1?1?0} planes and increased for the {1?1?1} plane. The difference between the activation energy of these etching processes for the three different crystallographic directions became rather small due to the combined effect of the oxidation and the subsequent etching sub-processes. This means that the temperature dependence of the number of kinks as chemical oxidation sites is very similar for the different planes. For the {1?1?1} plane the oxidation sub-process has a higher efficiency resulting in an increased etch rate whereas the etch rate decays for the {1?0?0} and {1?1?0} planes due to enhanced passivation, and these two phenomena contribute to the decrease of the anisotropy. Due to the addition of NaOCl, the oxidation sub-process is more isotropic but still site dependent. In the practice, the etched surface remains of good quality without defect development. In the presence of the oxidizing agent, the difference of the etch rates in the 1?0?0 and 1?1?0 directions is reversed to R100 < R110. This fact can be exploited in the formation of novel 3D structures on the (1?0?0) wafers by forming a square-masking pattern aligned precisely to the 1?0?0 directions.
- 22 August 2007
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 17 (9) , 1916-1922
Open AccessCharacterization of the anisotropic etching of silicon in two-component alkaline solution
The characteristics of wet chemical etching processes were compared for crystalline Si in aqueous solutions of pure NaOH and NaOH with added oxidizing agent NaOCl (sodium-hypochlorite). Due to the addition of NaOCl to the reference NaOH solution, the etch rate decreased for the {1?0?0} and {1?1?0} planes and increased for the {1?1?1} plane. The difference between the activation energy of these etching processes for the three different crystallographic directions became rather small due to the combined effect of the oxidation and the subsequent etching sub-processes. This means that the temperature dependence of the number of kinks as chemical oxidation sites is very similar for the different planes. For the {1?1?1} plane the oxidation sub-process has a higher efficiency resulting in an increased etch rate whereas the etch rate decays for the {1?0?0} and {1?1?0} planes due to enhanced passivation, and these two phenomena contribute to the decrease of the anisotropy. Due to the addition of NaOCl, the oxidation sub-process is more isotropic but still site dependent. In the practice, the etched surface remains of good quality without defect development. In the presence of the oxidizing agent, the difference of the etch rates in the 1?0?0 and 1?1?0 directions is reversed to R100 < R110. This fact can be exploited in the formation of novel 3D structures on the (1?0?0) wafers by forming a square-masking pattern aligned precisely to the 1?0?0 directions.