NHNiklas Hellgren

Niklas Hellgren

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Niklas Hellgren has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Si3N4/TiN Interface: 5. TiN/Si3N4 Grown and Analyzed In situ using Angle-resolved X-ray Photoelectron Spectroscopy

    by Richard T. Haasch, Jörg Patscheider, Niklas Hellgren, Ivan Petrov, J. E. Greene

    Angle-resolved x-ray photoelectron spectroscopy (AR-XPS) was used to analyze TiN/Si3N4 bilayers grown by ultrahigh vacuum reactive magnetron sputter deposition onto Si(001), with an electrically floating substrate potential of 7 V, in mixed 1:1 Ar/N2 discharges maintained at a total pressure of 0.5 Pa (3.75 × 10−3 Torr). The Si3N4 layers were deposited at room temperature and the 4-ML thick TiN overlayers were grown at 600 °C. AR-XPS spectra were obtained using incident monochromatic Al Kα x-radiation at 0.83401 nm. TiN/Si3N4 Ti 2p spectra reveal an unscreened final-state satellite intensity that lies between that of clean TiN(001) and Si3N4/TiN(001).

  • The Si3N4/TiN Interface: 6. Si/TiN(001) Grown and Analyzed In situ using Angle-resolved X-ray Photoelectron Spectroscopy

    by Richard T. Haasch, Jörg Patscheider, Niklas Hellgren, Ivan Petrov, J. E. Greene

    Angle-resolved x-ray photoelectron spectroscopy (AR-XPS) was used to analyze Si/TiN(001) bilayers grown by ultrahigh vacuum reactive magnetron sputter deposition on MgO(001), with an electrically floating substrate potential of 7 V, in mixed 1:1 Ar/N2 discharges maintained at a total pressure of 0.5 Pa (3.75 × 10−3 Torr). The TiN(001) films were grown at 600 °C and the 4-ML-thick Si overlayers at room temperature. AR-XPS spectra were obtained using incident monochromatic Al Kα x-radiation at 0.83401 nm. Si/TiN(001) Ti 2p spectra reveal reduced unscreened final-state satellite peaks compared to Ti 2p spectra obtained from uncapped TiN(001) due to increased electronic screening.

  • Fullerene-like BCN thin films: a computational and experimental study

    by Niklas Hellgren, Torun Berlind, Gueorgui K. Gueorguiev, Mats P. Johansson, Sven Stafström, Lars Hultman

  • Characterization of the metal–insulator interface of field-effect chemical sensors

    by A. Elisabeth Åbom, Richard T. Haasch, Niklas Hellgren, Nancy Finnegan, Lars Hultman, Mats Eriksson

    The metal–insulator interface of hydrogen-sensitive metal–insulator–semiconductor capacitors, with SiO2 as the insulator and Pt as the metal contact, has been studied. The thin Pt films were prepared in ultrahigh vacuum by electron beam evaporation and dc magnetron sputtering. Deposition parameters were substrate temperature and sputtering pressure. The hydrogen responses of the differently prepared devices were measured in a semi-inert ambient (and used as a measure of the concentration of available adsorption sites for hydrogen at the interface). A large variation of responses was found for differently prepared sensors, and the magnitude of the response was found to increase for decreasing bonding strength between the Pt film and the SiO2 substrate, as determined by scratch adhesion measurements. The bonding strength was controlled via the energetics of the Pt deposition flux. The largest interfacial roughness, from cavities between noncoalesced metal grains, and the poorest adhesion, was obtained by a reduced surface diffusion during growth and incomplete coalescence of the metal grains on the oxide surface as studied by transmission electron microscopy and atomic force microscopy. From x-ray photoelectron spectroscopy studies it was concluded that no chemical bonds were formed between Pt and SiO2. It is inferred that the hydrogen active in the sensor response is adsorbed on the oxide side of the interface in a spillover process. The difference in hydrogen response between differently prepared devices can be explained by a difference in concentration of available adsorption sites giving rise to a detectable dipole moment, on the oxide due to a blocking by Pt atoms in contact with the oxide. Thus, the concentration of Pt atoms in contact with the oxide affects both the hydrogen response and the metal–oxide adhesion.


  • Thermal stability of carbon nitride thin films

    by Niklas Hellgren, Nian Lin, Esteban Broitman, Virginie Serin, Stefano E. Grillo, Ray Twesten, Ivan Petrov, Christian Colliex, Lars Hultman, Jan-Eric Sundgren

    The thermal stability of carbon nitride films, deposited by reactive direct current magnetron sputtering in N2 discharge, was studied for postdeposition annealing temperatures TA up to 1000 °C. Films were grown at temperatures of 100 °C (amorphous structure) and 350 and 550 °C (fullerenelike structure) and were analyzed with respect to thickness, composition, microstructure, bonding structure, and mechanical properties as a function of TA and annealing time. All properties investigated were found to be stable for annealing up to 300 °C for long times (>48 h). For higher TA, nitrogen is lost from the films and graphitization takes place. At TA = 500 °C the graphitization process takes up to 48 h while at TA = 900 °C it takes less than 2 min. A comparison on the evolution of x-ray photoelectron spectroscopy, electron energy loss spectroscopy and Raman spectra during annealing shows that for TA > 800 °C, preferentially pyridinelike N and –C≡N is lost from the films, mainly in the form of molecular N2 and C2N2, while N substituted in graphite is preserved the longest in the structure. Films deposited at the higher temperature exhibit better thermal stability, but annealing at temperatures a few hundred degrees Celsius above the deposition temperature for long times is always detrimental for the mechanical properties of the films.


  • Anisotropies in magnetron sputtered carbon nitride thin films

    by Niklas Hellgren, Mats P. Johansson, Esteban Broitman, Lars Hultman, Jan-Eric Sundgren

    Carbon nitride CN x (0⩽x⩽0.35) thin films,deposited by reactive dc magnetron sputtering in Ar/N 2 discharges have been studied with respect to microstructure using electron microscopy, and elastic modulus using nanoindentation and surface acoustic wave analyses. For growth temperature of 100 ° C , the films were amorphous, and with an isotropic Young’s modulus of ∼170–200 GPa essentially unaffected by the nitrogen fraction. The filmsgrown at elevated temperatures (350–550 ° C ) show anisotropic mechanical properties due to a textured microstructure with standing basal planes, as observed from measuring the Young’s modulus in different directions. The modulus measured in the plane of the film was ∼60–80 GPa , while in the vertical direction the modulus increased considerably from ∼25 to ∼200 GPa as the nitrogen content was increased above ∼15 at. %.