Howard Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Howard Wang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Liwei Huang
Institute for Materials Research, Binghamton University, State University of New York, Binghamton, NY 13902, USA
6 shared publicationsKaikun Yang
Institute for Materials Research, Binghamton University, State University of New York, Binghamton, NY 13902, USA
5 shared publicationsCongkang Xu
Department of Mechanical Engineering, Binghamton University , State University of New York , Binghamton , New York
3 shared publicationsYayong Liu
Institute for Materials Research, Binghamton University, State University of New York, Binghamton, NY 13902, USA
3 shared publications- Congkang Xu
Department of Mechanical Engineering, Binghamton University, State University of New York, Binghamton, NY 13902, USA
2 shared publications Lianfeng Zou
Institute for Materials Research, Binghamton University , State University of New York , Binghamton , New York
2 shared publications
Latest Publications
- 30 September 2013
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 3 (45) , 23658-23663
Inkjet printing of palladium source and drain electrodes on individual single-wall carbon nanotubes to fabricate field effect transistors
Field effect transistors (FETs) have been fabricated on individual single-wall carbon nanotubes by inkjet printing of source and drain electrodes using palladium nanoparticles. The FETs display p-type semiconducting characteristics, whereas subsequent thermal annealing shows that both hole-doping and Schottky contacts have an influence on the electrical transport. The data show that inkjet printing is a viable tool for the facile fabrication of single-tube nanoelectronics.
- 30 September 2013
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 3 (45) , 23658-23663
Inkjet printing of palladium source and drain electrodes on individual single-wall carbon nanotubes to fabricate field effect transistors
Field effect transistors (FETs) have been fabricated on individual single-wall carbon nanotubes by inkjet printing of source and drain electrodes using palladium nanoparticles. The FETs display p-type semiconducting characteristics, whereas subsequent thermal annealing shows that both hole-doping and Schottky contacts have an influence on the electrical transport. The data show that inkjet printing is a viable tool for the facile fabrication of single-tube nanoelectronics.
- 15 July 2013
- Published by Taylor & Francis in Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry
- Vol. 43 (10) , 1501-1505
Low-Temperature Solution Synthesis of Zinc Oxide Nanotubes
Zinc oxide nanotubes (ZnO-NTs) have been successfully synthesized at ∼60°C using wet chemical method. ZnO-NTs have diameters of 100–200 nm and lengths of 1–2 μm. Transmission electron microscopy shows that as-synthesized NTs are single-crystal hexagonal structure and grown along [0001] direction. X-ray diffraction, ultravisible absorption, and photoluminescence results reveal that thermal treatments at low temperature of <500°C in air cannot apparently improve the crystal properties of as-synthesized ZnO.
- 15 July 2013
- Published by Taylor & Francis in Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry
- Vol. 43 (10) , 1501-1505
Low-Temperature Solution Synthesis of Zinc Oxide Nanotubes
Zinc oxide nanotubes (ZnO-NTs) have been successfully synthesized at ∼60°C using wet chemical method. ZnO-NTs have diameters of 100–200 nm and lengths of 1–2 μm. Transmission electron microscopy shows that as-synthesized NTs are single-crystal hexagonal structure and grown along [0001] direction. X-ray diffraction, ultravisible absorption, and photoluminescence results reveal that thermal treatments at low temperature of <500°C in air cannot apparently improve the crystal properties of as-synthesized ZnO.
- 26 January 2012
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 28 (5) , 2904-2908
Intercalating Oleylamines in Graphite Oxide
Graphite oxide has been synthesized from raw graphite particles and been treated with various mass amounts of oleylamine as intercalants to form intercalation compounds. X-ray diffraction patterns reveal that the inter-sheet distances strongly depend on the graphite oxide to oleylamine mass ratios. The equilibrium-like behavior implies diffusion-dominated oleylamine adsorption on graphite oxide in solution and excluded volume intercalations among oleylamine-adsorbed graphite oxide during restacking. The intercalation compounds are soluble in organic solvents, and their applications in the fabrication of transparent and conductive coatings have been demonstrated.
- 26 January 2012
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 28 (5) , 2904-2908
Intercalating Oleylamines in Graphite Oxide
Graphite oxide has been synthesized from raw graphite particles and been treated with various mass amounts of oleylamine as intercalants to form intercalation compounds. X-ray diffraction patterns reveal that the inter-sheet distances strongly depend on the graphite oxide to oleylamine mass ratios. The equilibrium-like behavior implies diffusion-dominated oleylamine adsorption on graphite oxide in solution and excluded volume intercalations among oleylamine-adsorbed graphite oxide during restacking. The intercalation compounds are soluble in organic solvents, and their applications in the fabrication of transparent and conductive coatings have been demonstrated.
- 26 March 2009
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 130 (12) , 124711
Cu-doping induced ferromagnetism in ZnO nanowires
Cu-doped and undoped ZnO nanowires have been successfully fabricated at 600 °C using a vapor transport approach. Comprehensive structural analyses on as-fabricated nanowires reveal highly crystalline ZnO nanowires with 0.5 at. % of substitutional Cu doping. Ferromagnetism has been observed in Cu-doped ZnO nanowires but not in undoped ones, which is probably associated with defects involving both Cu dopants and Zn interstitials.
- 26 March 2009
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 130 (12) , 124711
Cu-doping induced ferromagnetism in ZnO nanowires
Cu-doped and undoped ZnO nanowires have been successfully fabricated at 600 °C using a vapor transport approach. Comprehensive structural analyses on as-fabricated nanowires reveal highly crystalline ZnO nanowires with 0.5 at. % of substitutional Cu doping. Ferromagnetism has been observed in Cu-doped ZnO nanowires but not in undoped ones, which is probably associated with defects involving both Cu dopants and Zn interstitials.
- 14 November 2008
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 112 (49) , 19236-19241
Buckling and Ferromagnetism of Aligned Cr-Doped ZnO Nanorods
- 14 November 2008
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 112 (49) , 19236-19241
Buckling and Ferromagnetism of Aligned Cr-Doped ZnO Nanorods
- 1 January 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Sintering Metal Nanoparticle Films
We have carried out several measurements in order to understand the process of metal nanoparticle (MNP) film sintering. Small angle neutron scattering has been used to reveal the average diameters of silver and gold nanoparticles (Ag-NPs and Au-NPs) used in this study to be 4.6 and 3.8 nm, respectively, with a size distribution of ca. 20%. Spun- cast Ag-NP and Au-NP films have been sintered at temperature ranges of 80-160degC and 180-210 degC, respectively, for various times. The resulting film composition, morphology and electric resistance have been revealed. Upon sintering, the organic content in MNP films reduces to less than 10% while the overall film thickness reduces to about the half of the as-cast film thickness. The resistance of sintered Ag-NP films can vary over more than 7 decades depending on the sintering temperature. The conductivity of Ag-NP films sintered at 150degC is 2.4 times 10 -8 Omegam. The transport properties are affected by both the composition and morphology of sintered films.
- 1 January 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Sintering Metal Nanoparticle Films
We have carried out several measurements in order to understand the process of metal nanoparticle (MNP) film sintering. Small angle neutron scattering has been used to reveal the average diameters of silver and gold nanoparticles (Ag-NPs and Au-NPs) used in this study to be 4.6 and 3.8 nm, respectively, with a size distribution of ca. 20%. Spun- cast Ag-NP and Au-NP films have been sintered at temperature ranges of 80-160degC and 180-210 degC, respectively, for various times. The resulting film composition, morphology and electric resistance have been revealed. Upon sintering, the organic content in MNP films reduces to less than 10% while the overall film thickness reduces to about the half of the as-cast film thickness. The resistance of sintered Ag-NP films can vary over more than 7 decades depending on the sintering temperature. The conductivity of Ag-NP films sintered at 150degC is 2.4 times 10 -8 Omegam. The transport properties are affected by both the composition and morphology of sintered films.
- 1 February 2000
- Published by American Physical Society (APS) in Physical Review E
- Vol. 61 (2) , 1659-1663
Hydrodynamic-flow-driven wetting in thin film polymer blends: Growth kinetics and morphology
A thin film of deuterated poly(methyl methacrylate) (A) and poly(styrene-ran-acrylonitrile) at the critical composition is annealed in the two phase region to induce simultaneous phase separation and wetting of the A-rich phase at the surface. Using forward recoil spectrometry, the wetting layer thickness is found to grow linearly with time at and After selective etching of A, atomic force microscopy reveals a depletion layer having a bicontinuous, phase separated morphology. The A-rich tubes in this layer provide a pathway for rapid transport of the wetting phase from the bulk to the surface via hydrodynamic flow. Taken together, fast wetting layer growth and connectivity between the wetting layer and bulk provide unambiguous support for hydrodynamic-flow-driven wetting in thin film polymer blends.- 1 February 2000
- Published by American Physical Society (APS) in Physical Review E
- Vol. 61 (2) , 1659-1663
Hydrodynamic-flow-driven wetting in thin film polymer blends: Growth kinetics and morphology
A thin film of deuterated poly(methyl methacrylate) (A) and poly(styrene-ran-acrylonitrile) at the critical composition is annealed in the two phase region to induce simultaneous phase separation and wetting of the A-rich phase at the surface. Using forward recoil spectrometry, the wetting layer thickness is found to grow linearly with time at and After selective etching of A, atomic force microscopy reveals a depletion layer having a bicontinuous, phase separated morphology. The A-rich tubes in this layer provide a pathway for rapid transport of the wetting phase from the bulk to the surface via hydrodynamic flow. Taken together, fast wetting layer growth and connectivity between the wetting layer and bulk provide unambiguous support for hydrodynamic-flow-driven wetting in thin film polymer blends.