Andreas Reiter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Andreas Reiter has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Anders O. Eriksson
Oerlikon Balzers, Oerlikon Surface Solutions AG, Iramali 18, LI-9496 Balzers, Liechtenstein
1 shared publication - Bernhard Sartory
Materials Center Leoben Forschung GmbH, Leoben, Austria
1 shared publication - Christian Mitterer
Department of Materials Science Montanuniversität Leoben Leoben Austria
1 shared publication - Joerg Vetter
Oerlikon Balzers Coating Germany GmbH 1 , Am Böttcherberg 30-38, 51427 Bergisch Gladbach, Germany
1 shared publication - Volker Derflinger
Oerlikon Balzers, Oerlikon Surface Solutions AG, Iramali 18, LI-9496 Balzers, Liechtenstein
1 shared publication - Wolfgang Kalss
Oerlikon Balzers, Oerlikon Surface Solutions AG, Iramali 18, LI-9496 Balzers, Liechtenstein
1 shared publication
Latest Publications
- Open Access
Quo Vadis: AlCr-Based Coatings in Industrial Applications
AlCr-based hard nitride coatings with different chemical compositions and architectures have been successfully developed and applied over the last few decades. Coating properties are mainly influenced by deposition conditions and the Al/Cr content. The fcc structure is dominant for an Al-content up to Al0.7Cr0.3N and is preferred for most cutting applications. Different (AlCrX)N alloying concepts, including X = Si, W, B, V, have been investigated in order to enhance oxidation resistance and wear behaviour and to provide tribological properties. AlCr-based oxynitrides and even pure oxides (Al1−xCrx)2O3 with different crystalline structures have been explored. Multi- and nanolayered coatings within the AlCr materials system, as well as in combination with (TiSi)N, for example, have also been implemented industrially. The dominant deposition technology is the vacuum arc process. Recently, advanced high-power impulse magnetron sputtering (HiPIMS) processes have also been successfully applied on an industrial scale. This paper describes basic coating properties and briefly addresses the main aspects of the coating processes as well as selected industrial applications.
Open AccessQuo Vadis: AlCr-Based Coatings in Industrial Applications
AlCr-based hard nitride coatings with different chemical compositions and architectures have been successfully developed and applied over the last few decades. Coating properties are mainly influenced by deposition conditions and the Al/Cr content. The fcc structure is dominant for an Al-content up to Al0.7Cr0.3N and is preferred for most cutting applications. Different (AlCrX)N alloying concepts, including X = Si, W, B, V, have been investigated in order to enhance oxidation resistance and wear behaviour and to provide tribological properties. AlCr-based oxynitrides and even pure oxides (Al1−xCrx)2O3 with different crystalline structures have been explored. Multi- and nanolayered coatings within the AlCr materials system, as well as in combination with (TiSi)N, for example, have also been implemented industrially. The dominant deposition technology is the vacuum arc process. Recently, advanced high-power impulse magnetron sputtering (HiPIMS) processes have also been successfully applied on an industrial scale. This paper describes basic coating properties and briefly addresses the main aspects of the coating processes as well as selected industrial applications.
- 1 July 2007
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 25 (4) , 711-720
Oxidation of arc-evaporated Al1−xCrxN coatings
The recently introduced Al 1 − x Cr x N coatings are characterized by superior thermal stability and oxidation resistance. Although several studies on the microstructure and mechanical properties of these coatings have been published, the oxidation behavior and mechanisms were only investigated for Al 1 − x Cr x N with Cr ∕ Al ratio bigger than 1. Within this work, the oxidation of arc-evaporated Al 1 − x Cr x N coatings was investigated as a function of the Al content. Coatings were deposited onto cemented carbide substrates using an industrial-scale arc evaporation system (Balzers rapid coating system) and alloyed Al ∕ Cr targets yielding Al 1 − x Cr x N coatings ranging from x = 0.29 to x = 0.79 . Heat treatments in air were conducted in the temperature range between 900 and 1100 ° C . For comparison, samples were also annealed in Ar between 900 and 1200 ° C . Elemental distributions within the coating and the oxide layers were determined by secondary ion mass spectroscopy. After annealing in Ar, Cr was found to segregate to the coating surface following the decomposition of the face-centered cubic Al 1 − x Cr x N phase into hcp AlN and, under release of N 2 , Cr 2 N and later on Cr. Simultaneously, Al depletion was observed within the Cr enriched near-surface zone. In contrast, the decomposition of the cubic Al 1 − x Cr x N phase is severely hindred during annealing in air. Outward diffusion of Cr and Al, N depletion, and inward diffusion of O were observed, manifesting diffusion mechanisms depending on the initial coating composition. A protective mixed Cr 2 O 3 – Al 2 O 3 scale, at the coating surface mainly dominated by Cr 2 O 3 , was formed for all coating compositions investigated. This protective oxide scale prevents the decomposition of the cubic Al 1 − x Cr x N phase during high temperature exposure.
- 1 July 2007
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 25 (4) , 711-720
Oxidation of arc-evaporated Al1−xCrxN coatings
The recently introduced Al 1 − x Cr x N coatings are characterized by superior thermal stability and oxidation resistance. Although several studies on the microstructure and mechanical properties of these coatings have been published, the oxidation behavior and mechanisms were only investigated for Al 1 − x Cr x N with Cr ∕ Al ratio bigger than 1. Within this work, the oxidation of arc-evaporated Al 1 − x Cr x N coatings was investigated as a function of the Al content. Coatings were deposited onto cemented carbide substrates using an industrial-scale arc evaporation system (Balzers rapid coating system) and alloyed Al ∕ Cr targets yielding Al 1 − x Cr x N coatings ranging from x = 0.29 to x = 0.79 . Heat treatments in air were conducted in the temperature range between 900 and 1100 ° C . For comparison, samples were also annealed in Ar between 900 and 1200 ° C . Elemental distributions within the coating and the oxide layers were determined by secondary ion mass spectroscopy. After annealing in Ar, Cr was found to segregate to the coating surface following the decomposition of the face-centered cubic Al 1 − x Cr x N phase into hcp AlN and, under release of N 2 , Cr 2 N and later on Cr. Simultaneously, Al depletion was observed within the Cr enriched near-surface zone. In contrast, the decomposition of the cubic Al 1 − x Cr x N phase is severely hindred during annealing in air. Outward diffusion of Cr and Al, N depletion, and inward diffusion of O were observed, manifesting diffusion mechanisms depending on the initial coating composition. A protective mixed Cr 2 O 3 – Al 2 O 3 scale, at the coating surface mainly dominated by Cr 2 O 3 , was formed for all coating compositions investigated. This protective oxide scale prevents the decomposition of the cubic Al 1 − x Cr x N phase during high temperature exposure.