Xavier Fischer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Xavier Fischer has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Fouad Bennis
ECN IRCCyN – UMR CNRS 6597, Ecole Centrale de Nantes, 1, rue de la Noë – BP 92101, 44321 Nantes Cedex 03, France
5 shared publicationsJean-Pierre Nadeau
Esplanade des Arts et Métiers
5 shared publications- Pierre Joyot
I2M CNRS UMR 5295, Université de Bordeaux, ENSAM, Esplanade des Arts et Métiers
5 shared publications Keny Ordaz-Hernandez
3 shared publications- Ricardo Mejía-Gutiérrez
Universidad Eafit
3 shared publications - Stéphanie Cagin
ESTIA Recherche, 64210 Bidart, France
3 shared publications
Latest Publications
- 15 November 2018
- Published by Springer Nature in Applied Composite Materials
- Vol. 26 (2) , 643-662
Support for Decision Making in Design of Composite Laminated Structures. Part 1: Parametric Knowledge Model
- 15 November 2018
- Published by Springer Nature in Applied Composite Materials
- Vol. 26 (2) , 643-662
Support for Decision Making in Design of Composite Laminated Structures. Part 1: Parametric Knowledge Model
- 15 November 2018
- Published by Springer Nature in Applied Composite Materials
- Vol. 26 (2) , 663-681
Support for Decision Making in Design of Composite Laminated Structures. Part 2: Reduced Parametric Model-Based Optimization
- 15 November 2018
- Published by Springer Nature in Applied Composite Materials
- Vol. 26 (2) , 663-681
Support for Decision Making in Design of Composite Laminated Structures. Part 2: Reduced Parametric Model-Based Optimization
- Open Access
- 1 November 2017
- Published by EDP Sciences in Mechanics & Industry
- Vol. 18 (5) , 509
β-NTF reduction and fast kriging simulation of optimal engine configurations
In an optimization process, models are applied to simulate different design behaviors in order to determine the most suitable one. However, this requires the use of a structured methodology to correctly explore the design space and truly converge to the best solution. It is therefore necessary to test and validate the optimal design. For engines, two ways are essentially used: building and testing a real cylinder, or simulating the new design with Computational-Fluid-Dynamics (CFD) models. These two techniques are both expensive and time consuming. An alternative way is proposed to test new designs with a fast simulation based on a kriging method. The exploration of the design space is based on 27 cylinder configurations and the results of their CFD models. It converged to an optimal design depending on the objective function. A kriging method was used to interpolate the behavior of the optimal design just found. In this paper we present the β-NTF model reduction (to define the data set used by the kriging method) and the principle of the kriging technique. We then briefly discuss the results. The results underline the method's advantages despite the small gap between the expected results and those for kriging.
- 1 November 2017
- Published by EDP Sciences in Mechanics & Industry
- Vol. 18 (5) , 509
Open Accessβ-NTF reduction and fast kriging simulation of optimal engine configurations
In an optimization process, models are applied to simulate different design behaviors in order to determine the most suitable one. However, this requires the use of a structured methodology to correctly explore the design space and truly converge to the best solution. It is therefore necessary to test and validate the optimal design. For engines, two ways are essentially used: building and testing a real cylinder, or simulating the new design with Computational-Fluid-Dynamics (CFD) models. These two techniques are both expensive and time consuming. An alternative way is proposed to test new designs with a fast simulation based on a kriging method. The exploration of the design space is based on 27 cylinder configurations and the results of their CFD models. It converged to an optimal design depending on the objective function. A kriging method was used to interpolate the behavior of the optimal design just found. In this paper we present the β-NTF model reduction (to define the data set used by the kriging method) and the principle of the kriging technique. We then briefly discuss the results. The results underline the method's advantages despite the small gap between the expected results and those for kriging.
- 3 September 2016
- Published by Springer Nature
- p. 45-53
Neuro-separated meta-model of the scavenging process in 2-Stroke Diesel engine
- 3 September 2016
- Published by Springer Nature
- p. 45-53
Neuro-separated meta-model of the scavenging process in 2-Stroke Diesel engine
- 12 May 2016
- Published by SAGE Publications in SIMULATION
- Vol. 92 (6) , 507-520
A new reduced model of scavenging to optimize cylinder design
This paper presents the development of a new scavenging model to optimize cylinder design. The developed model explicitly integrates some of the cylinder’s design and environmental variables to describe flows during the scavenging process. Then, based on the reduced model, an optimization phase was carried out in order to determine the optimal values of cylinder variables. From computational fluid dynamics (CFD) models to optimal cylinder design, all method steps used are described in this paper. Adaptable to any type of engine, here it is applied to the particular two-stroke diesel engine with ports only. In order to fully understand fluid flow, the methodology integrates a number of CFD calculations with different cylinder configurations to provide data. The CFD results are used as neural network outputs during the training phase, whereas the cylinder variables plus the crankshaft angle are the inputs. The trained network provides the analytical reduced model for gas composition transiting through ports, which characterize the scavenging process. Thanks to these, genetic algorithms are run to define the most suitable values of cylinder variables in order to improve scavenging. The entire process for establishing the reduced model and the optimal design of the chamber is presented in this paper.
- 12 May 2016
- Published by SAGE Publications in SIMULATION
- Vol. 92 (6) , 507-520
A new reduced model of scavenging to optimize cylinder design
This paper presents the development of a new scavenging model to optimize cylinder design. The developed model explicitly integrates some of the cylinder’s design and environmental variables to describe flows during the scavenging process. Then, based on the reduced model, an optimization phase was carried out in order to determine the optimal values of cylinder variables. From computational fluid dynamics (CFD) models to optimal cylinder design, all method steps used are described in this paper. Adaptable to any type of engine, here it is applied to the particular two-stroke diesel engine with ports only. In order to fully understand fluid flow, the methodology integrates a number of CFD calculations with different cylinder configurations to provide data. The CFD results are used as neural network outputs during the training phase, whereas the cylinder variables plus the crankshaft angle are the inputs. The trained network provides the analytical reduced model for gas composition transiting through ports, which characterize the scavenging process. Thanks to these, genetic algorithms are run to define the most suitable values of cylinder variables in order to improve scavenging. The entire process for establishing the reduced model and the optimal design of the chamber is presented in this paper.
- 1 December 2012
- Published by Elsevier in Expert Systems with Applications
- Vol. 39 (18) , 13357-13365
Decision support method for the design of embedded energy in autonomous microsystems
- 1 December 2012
- Published by Elsevier in Expert Systems with Applications
- Vol. 39 (18) , 13357-13365
Decision support method for the design of embedded energy in autonomous microsystems