JPJosé Cidrás Pidre

José Cidrás Pidre

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


José Cidrás Pidre has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Non-Intrusive Electrical Monitoring for the Real-Time Estimation of Production Parameters in a Sheet Metal Stamping Line

    by Camilo Carrillo González, Eloy Díaz Dorado, Adrián Juan Pérez Peña, José Cidrás Pidre, Cristina Isabel Martínez Castañeda, José Florencio Sánchez Rúa

    Metal forming processes, characterized by high energy consumption, are widely used in modern manufacturing. In this context, methods for monitoring the operational state and cycle-dependent metrics of manufactured parts are essential for implementing energy optimization strategies. Such strategies require moving away from time-aggregated energy assessments, which fail to capture part-level variability, toward analyses at the granularity of individual parts. This article introduces a non-intrusive methodology to enable the identification, in real time, of the part under production and to estimate cycle time and energy consumption per part. The method relies on electrical measurements taken at the switchboards. The RMS current and power values are the inputs to a machine-learning (ML) approach that identifies the part in production. To this end, the time-domain and time–frequency-domain features extracted from the signals are employed to train a Support Vector Machine (SVM) classifier that achieves a test accuracy of 99.9%. Next, the approach estimates cycle time and energy per cycle in real time. Approximately 58,000 production cycles, corresponding to several part types, were characterized. The proposed approach demonstrates that part-level identification and per-cycle energy estimation can be achieved in real time using only electrical measurements in an industrial process.

  • Open Access

    Non-Intrusive Electrical Monitoring for Real-Time Estimation of the Production Parameters in a Sheet Metal Stamping Line

    by Camilo Carrillo González, Eloy Díaz Dorado, Adrián Juan Pérez Peña, José Cidrás Pidre, Cristina Isabel Martínez Castañeda, José Florencio Sánchez Rúa

    Metal forming processes play a key role in modern manufacturing, but they are characterized by high energy consumption and low overall efficiency. In this context, precise methods for monitoring the operational state and cycle-dependent metrics of manufactured parts are essential to implement energy optimization strategies. This article presents a data-driven and non-intrusive methodology to identify, in real time, the part under production and to estimate both cycle time and energy consumption per part. The method relies exclusively on electrical measurements taken at the main switchboard and at the first process-stage switchboard. These signals are used to calculate electrical quantities such as root mean square (RMS) current and active power, and a machine-learning (ML) approach is proposed to automatically identify the part in production. To this end, time-domain features are extracted directly from the signals, while time-frequency features are extracted using Continuous Wavelet Transform (CWT). These features are employed to train Support Vector Machine (SVM) classifiers optimized via grid search. Experimental results show that the model achieves a test accuracy of 99.9%. Once the production state is identified, the system estimates cycle time and energy per cycle in real time. Approximately 58,000 production cycles, corresponding to several part types were characterized.

  • Open Access

    Detailed Energy Analysis of a Sheet-Metal-Forming Press from Electrical Measurements

    by Camilo Carrillo, Eloy Díaz Dorado, José Cidrás Pidre, Julio Garrido Campos, Diego San Facundo López, Luiz A. Lisboa Cardoso, Cristina I. Martínez Castañeda, José F. Sánchez Rúa

    This paper presents a methodology that allows for the detection of the state of a sheet-metal-forming press, the parts being produced, their cadence, and the energy demand for each unit produced. For this purpose, only electrical measurements are used. The proposed analysis is conducted at the level of the press subsystems: main motor, transfer module, cushion, and auxiliary systems, and is intended to count, classify, and monitor the production of pressed parts. The power data are collected every 20 ms and show cyclic behavior, which is the basis for the presented methodology. A neural network (NN) based on heuristic rules is developed to estimate the press states. Then, the production period is determined from the power data using a least squares method to obtain normalized harmonic coefficients. These are the basis for a second NN dedicated to identifying the parts in production. The global error in estimating the parts being produced is under 1%. The resulting information could be handy in determining relevant information regarding the press behavior, such as energy per part, which is necessary in order to evaluate the energy performance of the press under different production conditions.


  • EVALUATION OF THE OPERATION OF A PUMP USED AS A TURBINE (PAT) UNDER REAL OPERATING CONDITIONS IN A DRINKING WATER TREATMENT STATION (DWTS)

    by Eloy Díaz Dorado, Jose Cidras Pidre, Julio Garrido Campos, Martin Casal, Fernando Guitián Guitián, Alejandro Arias Blanco, Isabel Fernandez Soñora, Diego Acevedo Iglesias, Angel Fernandez Vilan, Camilo José Carrillo González

    This paper analyzes the performance under real conditions of an axial flow hydraulic pump used as a turbine (Pump as Turbine or PaT) in a Drinking Water Treatment Station (DWTS). The DWTS is located at the municipality of Baiona (NW of Spain) and is supplied from a reservoir located at a height of about 50 m above the level of the plant. The existing difference in level at the intake makes it necessary to regulate the flow at the plant inlet by means of a valve, for which, prior to the development of the generation installation, a gate valve was used. In order to take advantage of the existing difference in level, a 6 kW micro-generation system was put into service using a PaT supported by a butterfly valve for flow regulation. The main reasons for choosing this generation system were the high cost of small turbines for the characteristics of the hydraulic connection of the DWTS and the limited availability of this type of device. The system is in service and being monitored by a SCADA since July 2019 so there is a relevant amount of records that allows analyzing different operating conditions. In the sizing of a BUTU system it is necessary to estimate the behavior as a turbine since the pump manufacturer only provides data in operation as a pump. There is a large literature proposing methods for estimating the performance of BUTU systems, however, the most widely accepted methods are those validated experimentally, as intended in this article. Keywords: PaT, renewable generation, micro-hydraulics En este artículo se analiza el comportamiento en condiciones reales de una bomba hidráulica de flujo axial usada como turbina (Bomba Usada como Turbina o BUTU) en una Estación de Tratamiento de Agua Potable (ETAP). La ETAP está situada en el ayuntamiento de Baiona (NO de España) y se abastece desde un embalse situado a una cota de unos 50 m por encima del nivel de la planta. El desnivel existente en la acometida hace necesaria la regulación del caudal a la entrada de planta mediante una válvula, para lo cual, previamente al desarrollo de la instalación de generación, se empleaba una válvula de compuerta. Con objeto de aprovechar el desnivel existente se puso en servicio un sistema de micro-generación de 6 kW para el que se utilizó una BUTU apoyada por una válvula de mariposa para la regulación de caudal. Los principales motivos para la elección de este sistema de generación fueron el elevado coste de las turbinas de pequeña potencia para las características de la acometida hidráulica de la ETAP y la escasa disponibilidad de este tipo de dispositivos. El sistema está en servicio y siendo monitorizado mediante un SCADA desde julio de 2019 por lo que se dispone una cantidad de registros relevante que permite analizar distintas condiciones de funcionamiento. En el dimensionamiento de un sistema BUTU es necesario estimar el comportamiento como turbina ya que el fabricante de la bomba sólo aporta datos en funcionando como bomba. Existe numerosa bibliografía en la que se proponen métodos de estimación del comportamiento de los sistemas BUTU, sin embargo, los métodos de mayor aceptación son aquellos validades validados experimentalmente, tal y como se pretendelos cuales son evaluados en este artículo. Palabras clave: BUTU, generación renovable, microhidráulica


  • Open Access

    A STATCOM with Supercapacitors for Low-Voltage Ride-Through in Fixed-Speed Wind Turbines

    by Andrés Felipe Obando-Montaño, Camilo Carrillo, José Cidrás, Eloy Díaz-Dorado

    Fixed-speed wind generator (FSWG) technology has an important presence in countries where wind energy started to be developed more than a decade ago. This type of technology cannot be directly adapted to the grid codes, for example those requirements related to the immunity level under voltage dips. That behavior is typically referred as low-voltage ride through (LVRT), and it usually implies certain reactive and active power injection requirements, both during a voltage dip and during the voltage recovery. In this context, a review is presented of the LVRT exigencies present in some of the countries with the most advanced grid codes (Denmark, Germany, Spain and the United Kingdom). In this paper, the capabilities of STATCOM-based devices for fulfilling the LVRT requirements in FSWGs are analyzed. For this purpose, two technologies are considered: a STATCOM with a supercapacitor, which improves its energy storage features; and a STATCOM with a supercapacitor and a DC-DC converter, to achieve higher discharge levels.


  • Open Access

    An Approach to Determine the Weibull Parameters for Wind Energy Analysis: The Case of Galicia (Spain)

    by Camilo Carrillo, José Cidrás, Eloy Díaz-Dorado, Andrés Felipe Obando-Montaño

    The Weibull probability density function (PDF) has mostly been used to fit wind speed distributions for wind energy applications. The goodness of fit of the results depends on the estimation method that was used and the wind type of the analyzed area. In this paper, a study on a particular area (Galicia) was performed to test the performance of several fitting methods. The goodness of fit was evaluated by well-known indicators that use the wind speed or the available wind power density. However, energy production must be a critical parameter in wind energy applications. Hence, a fitting method that accounts for the power density distribution is proposed. To highlight the usefulness of this method, indicators that use energy production values are also presented.