Atsushi Konno
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Atsushi Konno has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Masaru Uchiyama
Tōhoku Univ
27 shared publications - Satoko Abiko
Shibaura Institute of Technology
9 shared publications - Teppei Tsujita
Tohoku University
6 shared publications Xin Jiang
Department of Mechanical Systems and Design , Graduate School of Engineering, Tohoku University , 6-6-01, 980-8579 , A , Sendai, Miyagi , Japan
6 shared publications- Koichi Kita
Department of Aerospace Engineering, Tohoku University
3 shared publications Koichi Nagashima
3 shared publications
Latest Publications
- 14 May 2013
- Published by Taylor & Francis in Advanced Robotics
- Vol. 27 (12) , 907-917
Compensation for dead band of force measurement based on the coefficient of restitution in a hybrid simulator
In order to develop space robotic technologies, the feasibility and reliability of the systems have to be verified by repetitive operation tests. A hybrid simulator (also referred to as a Hardware-in-the-loop simulator) is one of the effective ways to examine orbital operations on the ground. The simulator embeds a hardware experiment in a numerical simulation loop. However, it is known that the hybrid simulator has a serious problem that energy increase arises in contact with a hardware experiment in the loop. In general, the energy increase in the hybrid simulator occurs due to the dead time in the system. However, this paper presents that dead band in force/torque measuring also causes the energy increase. The dead band in the force/torque measuring is necessary to avoid unexpected motion of the hybrid simulator due to the noise data in the force/torque sensor. This paper proposes two compensation methods for the energy increase problem due to the dead band. The first method is to insert a virtual damper to absorb the increased energy during the contact. The second method is to extrapolate force/torque data that is lost through the dead band processing right after the contact. The experimental verification with uniaxial contact in hybrid simulator is carried out to validate the proposed compensation methods.
- 14 May 2013
- Published by Taylor & Francis in Advanced Robotics
- Vol. 27 (12) , 907-917
Compensation for dead band of force measurement based on the coefficient of restitution in a hybrid simulator
In order to develop space robotic technologies, the feasibility and reliability of the systems have to be verified by repetitive operation tests. A hybrid simulator (also referred to as a Hardware-in-the-loop simulator) is one of the effective ways to examine orbital operations on the ground. The simulator embeds a hardware experiment in a numerical simulation loop. However, it is known that the hybrid simulator has a serious problem that energy increase arises in contact with a hardware experiment in the loop. In general, the energy increase in the hybrid simulator occurs due to the dead time in the system. However, this paper presents that dead band in force/torque measuring also causes the energy increase. The dead band in the force/torque measuring is necessary to avoid unexpected motion of the hybrid simulator due to the noise data in the force/torque sensor. This paper proposes two compensation methods for the energy increase problem due to the dead band. The first method is to insert a virtual damper to absorb the increased energy during the contact. The second method is to extrapolate force/torque data that is lost through the dead band processing right after the contact. The experimental verification with uniaxial contact in hybrid simulator is carried out to validate the proposed compensation methods.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _2P1-U03_1
2P1-U03 Evaluation of Real-time Performance of the Blunt Dissection Simulator using a Real Brain Model(Surgical Robotics and Mechatronics(2))
Surgery simulator is expected to help plan surgery procedures and train surgical techniques. In brain surgery, blunt dissection simulation is needed because it is a basic and important technique. Nakayama et al. proposed a method of computing fracture of soft tissue for blunt dissection simulation. However real-time simulation had not been achieved because of its high computational cost. This paper shows the system of the blunt dissection simulator with a haptic interface, and proposes a method for construction of real brain Finite Element Method(FEM) model by scanning the surface of a pig brain using a laser displacement sensor. Additionally the real-time performance of the simulator which parallelized by a multi-core processor is evaluated.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _2P1-U03_1
2P1-U03 Evaluation of Real-time Performance of the Blunt Dissection Simulator using a Real Brain Model(Surgical Robotics and Mechatronics(2))
Surgery simulator is expected to help plan surgery procedures and train surgical techniques. In brain surgery, blunt dissection simulation is needed because it is a basic and important technique. Nakayama et al. proposed a method of computing fracture of soft tissue for blunt dissection simulation. However real-time simulation had not been achieved because of its high computational cost. This paper shows the system of the blunt dissection simulator with a haptic interface, and proposes a method for construction of real brain Finite Element Method(FEM) model by scanning the surface of a pig brain using a laser displacement sensor. Additionally the real-time performance of the simulator which parallelized by a multi-core processor is evaluated.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _2P1-U04_1
2P1-U04 Development and Evaluation of a Haptic Interface for a Brain Surgery Simulator(Surgical Robotics and Mechatronics(2))
In this paper, development and evaluation of a haptic device for a brain surgery simulator are presented. The haptic device enables to simulate medical operations with both hands at the area near the tip of two surgical instruments. In this study, a module for micro scissors was developed and evaluated by force display experiment. Furthermore, force display performance of the haptic device was evaluated by push simulation using a cube model of brain tissue. The results clarify the issues of the module and the haptic device.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _2P1-U04_1
2P1-U04 Development and Evaluation of a Haptic Interface for a Brain Surgery Simulator(Surgical Robotics and Mechatronics(2))
In this paper, development and evaluation of a haptic device for a brain surgery simulator are presented. The haptic device enables to simulate medical operations with both hands at the area near the tip of two surgical instruments. In this study, a module for micro scissors was developed and evaluated by force display experiment. Furthermore, force display performance of the haptic device was evaluated by push simulation using a cube model of brain tissue. The results clarify the issues of the module and the haptic device.
- Open Access
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _1A2-N01_1
1A2-N01 Mobile Manipulation of a Humanoid Robot(Humanoid(2))
This paper presents a method for generating whole body motion including the walking based on the hand trajectory. It is necessary to generate the hand and walking trajectory considering the interaction between manipulation and walking for mobile manipulation. However, to generate the walking trajectory, many elements need to be considered simultaneously. This study aims to generate whole body motion, including the walking based on only the hand trajectory. Firstly, a virtual joint model, which substitutes the biped model, is proposed. The walking trajectory is generated based on the hand trajectory by using this model. Secondly, a method for generating whole body motion including walking is presented. Finally, the effectiveness of the proposed method is evaluated by simulations and experiments.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _1A2-N01_1
Open Access1A2-N01 Mobile Manipulation of a Humanoid Robot(Humanoid(2))
This paper presents a method for generating whole body motion including the walking based on the hand trajectory. It is necessary to generate the hand and walking trajectory considering the interaction between manipulation and walking for mobile manipulation. However, to generate the walking trajectory, many elements need to be considered simultaneously. This study aims to generate whole body motion, including the walking based on only the hand trajectory. Firstly, a virtual joint model, which substitutes the biped model, is proposed. The walking trajectory is generated based on the hand trajectory by using this model. Secondly, a method for generating whole body motion including walking is presented. Finally, the effectiveness of the proposed method is evaluated by simulations and experiments.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _1P1-Q02_1
1P1-Q02 Development of Real-Time Control System of Humanoid Robot HOAP-2 Based on the Linux Real-Time Preempt and Application by using RT-Components(RT Middleware and Open System)
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2012, _1P1-Q02_1
1P1-Q02 Development of Real-Time Control System of Humanoid Robot HOAP-2 Based on the Linux Real-Time Preempt and Application by using RT-Components(RT Middleware and Open System)
- Open Access
- 1 January 2012
- Published by The Robotics Society of Japan in Journal of the Robotics Society of Japan
- Vol. 30 (2) , 160-162
Innovation of the Production Process by Parallel Link Robot
- 1 January 2012
- Published by The Robotics Society of Japan in Journal of the Robotics Society of Japan
- Vol. 30 (2) , 160-162
Open AccessInnovation of the Production Process by Parallel Link Robot
- 1 January 2011
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2011, _2P2-I10_1
2P2-I10 Walking Simulation of a Biped Robot on Loose Soil using Footprint Map(Humanoid)
- 1 January 2011
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2011, _2P2-I10_1
2P2-I10 Walking Simulation of a Biped Robot on Loose Soil using Footprint Map(Humanoid)
- 1 January 2011
- Published by Taylor & Francis in Advanced Robotics
- Vol. 25 (6-7) , 805-823
Wrist Camera-Based Vibration Suppression Control for a Flexible Manipulator
This paper addresses a vision-based method for estimating vibration excited in the tip of a flexible-link manipulator. In this method, estimation of vibration is achieved by observing the variation of image features projected on a wrist camera. It mimics the situation of utilizing a wrist camera in tip vibration control of a space manipulator. In space, a vision sensor can be expected to be a feasible means for measuring the elastic vibration of the space manipulators, since they are more reliable compared with sensors like strain gauges. The method proposed in this paper takes advantage of the frequential characteristics of visual information that are reflected as a blurred background scene. With the high-frequency component of the projected image features, a Kalman filter-based observer is implemented as the estimator for the vibration. This implementation is characterized by the considerations of incorporating the slow sensor of the camera in the fast servo loop and compensation of the time delay due to image processing. With the vibration estimator, vibration suppression control relying solely on a wrist camera becomes possible. This scheme is successfully verified by experiments.
- 1 January 2011
- Published by Taylor & Francis in Advanced Robotics
- Vol. 25 (6-7) , 805-823
Wrist Camera-Based Vibration Suppression Control for a Flexible Manipulator
This paper addresses a vision-based method for estimating vibration excited in the tip of a flexible-link manipulator. In this method, estimation of vibration is achieved by observing the variation of image features projected on a wrist camera. It mimics the situation of utilizing a wrist camera in tip vibration control of a space manipulator. In space, a vision sensor can be expected to be a feasible means for measuring the elastic vibration of the space manipulators, since they are more reliable compared with sensors like strain gauges. The method proposed in this paper takes advantage of the frequential characteristics of visual information that are reflected as a blurred background scene. With the high-frequency component of the projected image features, a Kalman filter-based observer is implemented as the estimator for the vibration. This implementation is characterized by the considerations of incorporating the slow sensor of the camera in the fast servo loop and compensation of the time delay due to image processing. With the vibration estimator, vibration suppression control relying solely on a wrist camera becomes possible. This scheme is successfully verified by experiments.