Young-Soo Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Young-Soo Yang has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Kang-Yul Bae
Department of Mechatronics Engineering, Gyeongnam National University of Science and Technology, Jinju, Gyeongnam, South Korea
8 shared publicationsChung-Min Hyun
Samsung Heavy Industries Co. Ltd., Geoje, Gyeongnam, South Korea
4 shared publications- Kang-Yul Bae
Department of Mechatronics Engineering, Gyeongnam National University of Science and Technology, Jinju-si, Gyeongsangnam-do, South Korea
4 shared publications Truong-Thinh Nguyen
Department of Mechanical Engineering, Chonnam National University, Gwang-ju, Korea
3 shared publicationsBum-Ho Choi
National Center for Nanoprocess and Equipments, Korea Institute of Industrial Technology, Gwangju, Korea
1 shared publicationChan-Man Jeong
Department of Mechanical Engineering, Chonnam National University, Kwangju, South Korea
1 shared publication
Latest Publications
- Open Access
- 28 February 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42 (1) , 134-140
Prediction of Laser Welding Distortion in Cylindrical Shell Structures Using Direct Application of Inherent Strain
In this study, a simplified analysis method by directly applying inherent strain (DIS) at integration points to predict welding distortion of cylindrical shell structures was suggested. The 3D thermo-elastoplastic method demands substantial computational time. The strain as direct boundary (SDB) simplified method using virtual temperature encounters challenges in consecutive thermal structural analysis including welding distortion. The suggested method (that is, DIS) offers the advantage of enabling continuous thermal structural analysis after welding distortion analysis, with computational efficiency. To calculate inherent strain, lap laser welding with 2 mm and 2.6 mm SUS304 plates was performed, measuring fusion and heat-affected zone sizes via cross-sectional observations. Using the calculated inherent strain and our suggested direct input method, we conducted welding analysis and welding test on cylindrical shell structures. Comparison of welding distortion under same conditions revealed radial distortion difference within approximately 10%, corresponding with the experimental result and confirming a computational time reduction by over 2,000 times than those of thermo-elastoplastic analysis. Therefore, an efficient and accurate prediction of welding distortion was achievable through the suggested method.
- 28 February 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42 (1) , 134-140
Open AccessPrediction of Laser Welding Distortion in Cylindrical Shell Structures Using Direct Application of Inherent Strain
In this study, a simplified analysis method by directly applying inherent strain (DIS) at integration points to predict welding distortion of cylindrical shell structures was suggested. The 3D thermo-elastoplastic method demands substantial computational time. The strain as direct boundary (SDB) simplified method using virtual temperature encounters challenges in consecutive thermal structural analysis including welding distortion. The suggested method (that is, DIS) offers the advantage of enabling continuous thermal structural analysis after welding distortion analysis, with computational efficiency. To calculate inherent strain, lap laser welding with 2 mm and 2.6 mm SUS304 plates was performed, measuring fusion and heat-affected zone sizes via cross-sectional observations. Using the calculated inherent strain and our suggested direct input method, we conducted welding analysis and welding test on cylindrical shell structures. Comparison of welding distortion under same conditions revealed radial distortion difference within approximately 10%, corresponding with the experimental result and confirming a computational time reduction by over 2,000 times than those of thermo-elastoplastic analysis. Therefore, an efficient and accurate prediction of welding distortion was achievable through the suggested method.
- 27 July 2023
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 24 (10) , 1781-1791
Using a Novel CNN Model for Predicting the Induction Heating Lines to Obtain a Desired Deformed Shape of Steel Plate
- 27 July 2023
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 24 (10) , 1781-1791
Using a Novel CNN Model for Predicting the Induction Heating Lines to Obtain a Desired Deformed Shape of Steel Plate
- Open Access
- 30 June 2017
- Published by ENGG Journals Publications in International Journal of Engineering and Technology
- Vol. 9 (3) , 1777-1787
Numerical analysis of the process of pipe connection with a clamping ring using the finite element method
- 30 June 2017
- Published by ENGG Journals Publications in International Journal of Engineering and Technology
- Vol. 9 (3) , 1777-1787
Open AccessNumerical analysis of the process of pipe connection with a clamping ring using the finite element method
- 30 December 2016
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 15 (6) , 24-34
Analysis of Welding Distortion during the Production of Fuel Tanks for Excavators
Analysis of Welding Distortion during the Production of Fuel Tanks for Excavators Fuel Tank;Welding Deformation;Thermo-elasto-plastic Analysis;Finite Element Method;Welding Sequence; To attach a fuel tank to an excavator, two sets of mounting plates on which three bosses are attached are welded onto the tank. In this study, the welding process of a fuel tank for an excavator was modeled using a finite element numerical method. The tank was modeled as a simple plate to which the mounting plate or bosses were attached by fillet welding. Thermal and thermo-elasto-plastic analyses of the welding process were carried out to predict the temperature distribution and material distortion during welding, respectively. Three different welding sequences for the tank were also modelled to compare the deformation that occurred due to each welding sequence. The results of the analysis predicted that changing the welding sequence around the mounting plate could not position the boss within the allowable dimensional range. The results also revealed the sequence in which the maximum distortion of the bosses welded onto the tank was 30% less than the maximum distortion due to the other sequences.
- 30 December 2016
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 15 (6) , 24-34
Analysis of Welding Distortion during the Production of Fuel Tanks for Excavators
Analysis of Welding Distortion during the Production of Fuel Tanks for Excavators Fuel Tank;Welding Deformation;Thermo-elasto-plastic Analysis;Finite Element Method;Welding Sequence; To attach a fuel tank to an excavator, two sets of mounting plates on which three bosses are attached are welded onto the tank. In this study, the welding process of a fuel tank for an excavator was modeled using a finite element numerical method. The tank was modeled as a simple plate to which the mounting plate or bosses were attached by fillet welding. Thermal and thermo-elasto-plastic analyses of the welding process were carried out to predict the temperature distribution and material distortion during welding, respectively. Three different welding sequences for the tank were also modelled to compare the deformation that occurred due to each welding sequence. The results of the analysis predicted that changing the welding sequence around the mounting plate could not position the boss within the allowable dimensional range. The results also revealed the sequence in which the maximum distortion of the bosses welded onto the tank was 30% less than the maximum distortion due to the other sequences.
- 31 August 2014
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 32 (4) , 69-74
Analysis of Welding Distortion of Large Steel Plate by Using Analytical Solution of Temperature Distribution and Finite Element Method
- 31 August 2014
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 32 (4) , 69-74
Analysis of Welding Distortion of Large Steel Plate by Using Analytical Solution of Temperature Distribution and Finite Element Method
- 9 April 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (6) , 881-889
Analysis of magnetic field distribution in a cylindrical-type magnetron sputtering system
The magnetic field distribution in magnetron sputtering processes has been verified to influence the collision of positive ions on the target, as well as the efficiency of the deposition onto the substrate. However, locally concentrated collision due to the distribution has also been known to lead to nonuniform erosion on the target, which deteriorates the efficiency of sputtering. In this study, a cylindrical magnetron sputtering system with a rotary-type target is proposed to improve the expected lifetime of the target by reducing the local erosion of target in the magnetron sputtering process. For the sputtering system, the magnetic field distribution over the target was analyzed with finite element method. Based on the analysis, the effect of the configuration of permanent magnets on the magnetic field distribution was investigated. The result of the analysis could be used to predict the region where concentration of positive ions occurs and thus to estimate the pattern of how the erosion on the target surface would occur for the proposed system. The results also reveal that the magnetic field distribution related to the erosion pattern could be controlled with the configuration of the permanent magnets.
- 9 April 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (6) , 881-889
Analysis of magnetic field distribution in a cylindrical-type magnetron sputtering system
The magnetic field distribution in magnetron sputtering processes has been verified to influence the collision of positive ions on the target, as well as the efficiency of the deposition onto the substrate. However, locally concentrated collision due to the distribution has also been known to lead to nonuniform erosion on the target, which deteriorates the efficiency of sputtering. In this study, a cylindrical magnetron sputtering system with a rotary-type target is proposed to improve the expected lifetime of the target by reducing the local erosion of target in the magnetron sputtering process. For the sputtering system, the magnetic field distribution over the target was analyzed with finite element method. Based on the analysis, the effect of the configuration of permanent magnets on the magnetic field distribution was investigated. The result of the analysis could be used to predict the region where concentration of positive ions occurs and thus to estimate the pattern of how the erosion on the target surface would occur for the proposed system. The results also reveal that the magnetic field distribution related to the erosion pattern could be controlled with the configuration of the permanent magnets.
- 6 February 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (3) , 423-429
Analysis for the angular deformation of steel plates in a high-frequency induction forming process with a triangle heating technique
A triangle heating technique with the use of a heat source of high-frequency induction heating to make a steel plate deformed into a curved shape was modeled and analyzed using the numerical analysis of the finite element method in order to predict the angular deformation of the steel plate formed by the technique. For the analysis of the deformation, heat generation by an electromagnetic field was first analyzed with consideration of the preheat effect, and heat flow using the heat generated from the plate as the heat source was then analyzed. Thermal history of the plate predicted by numerical analysis was compared with that measured in an experiment of triangle heating on a steel plate. Deformations of the plates were then analyzed with changes of heating parameters including heating dimensions and plate thickness. The analyses were also verified with a series of experiments. In order to derive a simplified equation to readily predict deformation from the triangle heating technique, deformations predicted by numerical analyses and measured by the experiments were synthesized in association with the heating parameters using a statistical method of recursion analysis. The equation was verified to be able to predict the deformations conversely and expected to be practically used in the industry to select the heating parameters for the desired shapes of curved plates.
- 6 February 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 227 (3) , 423-429
Analysis for the angular deformation of steel plates in a high-frequency induction forming process with a triangle heating technique
A triangle heating technique with the use of a heat source of high-frequency induction heating to make a steel plate deformed into a curved shape was modeled and analyzed using the numerical analysis of the finite element method in order to predict the angular deformation of the steel plate formed by the technique. For the analysis of the deformation, heat generation by an electromagnetic field was first analyzed with consideration of the preheat effect, and heat flow using the heat generated from the plate as the heat source was then analyzed. Thermal history of the plate predicted by numerical analysis was compared with that measured in an experiment of triangle heating on a steel plate. Deformations of the plates were then analyzed with changes of heating parameters including heating dimensions and plate thickness. The analyses were also verified with a series of experiments. In order to derive a simplified equation to readily predict deformation from the triangle heating technique, deformations predicted by numerical analyses and measured by the experiments were synthesized in association with the heating parameters using a statistical method of recursion analysis. The equation was verified to be able to predict the deformations conversely and expected to be practically used in the industry to select the heating parameters for the desired shapes of curved plates.
- 3 April 2012
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 13 (4) , 539-545
Analysis of triangle heating technique using high frequency induction heating in forming process of steel plate
- 3 April 2012
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 13 (4) , 539-545
Analysis of triangle heating technique using high frequency induction heating in forming process of steel plate
- 4 February 2011
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 12 (1) , 105-113
Prediction of heating-line paths in induction heating process using the artificial neural network
- 4 February 2011
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 12 (1) , 105-113
Prediction of heating-line paths in induction heating process using the artificial neural network