Jostein Røyset
Research Subjects
Jostein Røyset has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Oddvin Reiso
Hydro Aluminium Research and Technology Development Sunndal, Romsdalsvegen 1, 6600 Sunndalsøra, Norway
2 shared publicationsAlessio Tocco
Universitá Politecnica delle Marche, Dipartimento di Meccanica, 60121 Ancona, Italy
1 shared publication- Bjørn Holmedal
Department of Materials Science and Engineering, Norwegian University of Science and Technology, Trondheim, Norway
1 shared publication - Calin Daniel Marioara
SINTEF Industry, Trondheim, Norway
1 shared publication Cristina Espezel
Hydro Aluminium Extrusion Ingot Customer Support, P.O. Box 980 Skøyen, 0240 Oslo, Norway
1 shared publicationDiego Bettella
Universitá Politecnica delle Marche, Dipartimento di Meccanica, 60121 Ancona, Italy
1 shared publication
Latest Publications
- Open Access
- 22 July 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 151 (1) , 14
Using Sc and Zr for Dispersoid Formation in an Al-Mg-Si Alloy
Four Al-Mg-Si alloys, three of them with additions of scandium or scandium and zirconium, were cast, homogenised at 550 °C, and precipitation hardened at 175 °C. For the alloy with the highest Sc content, significant discontinuous precipitation of Al3Sc took place during cooling after casting. Homogenisation for 1 h led to the formation of Al3Sc or Al3(Sc,Zr) dispersoids. The Al3(Sc,Zr) dispersoids were found in higher number densities than the Al3Sc dispersoids, and the latter were not stable for longer homogenisation times. TEM observations indicate that the Al3Sc or Al3(Sc,Zr) dispersoids are not preferred nucleation sites for metastable (Mg,Si) particles. The precipitation hardening behaviour of the Al-Mg-Si alloys was not altered by the Sc or Sc+Zr additions.
- 22 July 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 151 (1) , 14
Open AccessUsing Sc and Zr for Dispersoid Formation in an Al-Mg-Si Alloy
Four Al-Mg-Si alloys, three of them with additions of scandium or scandium and zirconium, were cast, homogenised at 550 °C, and precipitation hardened at 175 °C. For the alloy with the highest Sc content, significant discontinuous precipitation of Al3Sc took place during cooling after casting. Homogenisation for 1 h led to the formation of Al3Sc or Al3(Sc,Zr) dispersoids. The Al3(Sc,Zr) dispersoids were found in higher number densities than the Al3Sc dispersoids, and the latter were not stable for longer homogenisation times. TEM observations indicate that the Al3Sc or Al3(Sc,Zr) dispersoids are not preferred nucleation sites for metastable (Mg,Si) particles. The precipitation hardening behaviour of the Al-Mg-Si alloys was not altered by the Sc or Sc+Zr additions.
- Open Access
The Effect of Elastic Strain and Small Plastic Deformation on Tensile Strength of a Lean Al–Mg–Si Alloy
Al–Mg–Si alloys are usually formed into their final shape by rolling or extrusion. After extrusion, the aluminium profiles are usually straightened, causing the material to be subjected to a small plastic deformation. This study demonstrates the positive effect on strength that can be obtained from such small deformation levels or from only elastically straining the material. Elastic straining of a lean Al–Mg–Si alloy, when performed immediately after solution heat treatment, enhances the material yield strength after artificial ageing to T6. Transmission electron microscopy shows that this effect can be attributed to a higher number density and finer dispersion of the age-hardening precipitate needles. Furthermore, introducing a small plastic deformation of 1% after solution heat treatment results in a comparable strength increase to elastically straining the material. In this case, however, the strength increase is due to the increased dislocation density, which compensates for a lower density of precipitate needles. Finally, by combining plastic deformation with a succeeding elastic strain, we demonstrate how elastic strain can cause an on-set of dislocation cell formation in this material.
Open AccessThe Effect of Elastic Strain and Small Plastic Deformation on Tensile Strength of a Lean Al–Mg–Si Alloy
Al–Mg–Si alloys are usually formed into their final shape by rolling or extrusion. After extrusion, the aluminium profiles are usually straightened, causing the material to be subjected to a small plastic deformation. This study demonstrates the positive effect on strength that can be obtained from such small deformation levels or from only elastically straining the material. Elastic straining of a lean Al–Mg–Si alloy, when performed immediately after solution heat treatment, enhances the material yield strength after artificial ageing to T6. Transmission electron microscopy shows that this effect can be attributed to a higher number density and finer dispersion of the age-hardening precipitate needles. Furthermore, introducing a small plastic deformation of 1% after solution heat treatment results in a comparable strength increase to elastically straining the material. In this case, however, the strength increase is due to the increased dislocation density, which compensates for a lower density of precipitate needles. Finally, by combining plastic deformation with a succeeding elastic strain, we demonstrate how elastic strain can cause an on-set of dislocation cell formation in this material.
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 10, 185-192
Al-Mg-Si billets with high extrudability – state of the art and beyond
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 10, 185-192
Al-Mg-Si billets with high extrudability – state of the art and beyond
- 10 May 2007
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 483-484, 175-178
On the addition of precipitation- and work-hardening in an Al–Sc alloy
- 10 May 2007
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 483-484, 175-178
On the addition of precipitation- and work-hardening in an Al–Sc alloy