Hugo Bender
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hugo Bender has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
A. Torres
IMEC, Kapeldreef 75, B-3001 Leuven, Belgium
1 shared publication- Alain Claverie
CEMES-CNRS, 29 rue Jeanne Marvig, 31055 Toulouse, France
1 shared publication - Andre Vantomme
KU Leuven
1 shared publication - Antonio Cacciato
IMEC, Leuven, Belgium
1 shared publication Arnaud Furnémont
Furné, IMEC, Kapeldreef 75, Leuven, B-3001, Belgium
1 shared publication- Aude Rothschild
IMEC, Kapeldreef 75, Leuven, B-3001, Belgium
1 shared publication
Latest Publications
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1071
Effect of Top Dielectric Morphology and Gate Material on the Performance of Nitride-based FLASH Memory Cells
The nitride-based SONOS cell, for its excellent scalability and process simplicity, is the candidate to push the scaling roadmap for FLASH memories beyond the limit imposed on floating-gate memories by the electrostatic interference between adjacent cells. The traditional SONOS cell consists of a nitride layer (the storage element) encapsulated by two SiO2 layers which isolate the nitride layer from the Si substrate and the poly-Si gate (Poly-Si/SiO2/Si3N4/SiO2/c-Si). However, the thick tunnel oxide necessary to meet the retention requirements imposes a severe limit on the erase performance because of the erase saturation phenomenon. One possibility to guarantee both the erase and the retention performance is the replacement of the top SiO2 layer with materials of higher dielectric constant (high-k dielectric). The presence of a high-k dielectric reduces the electric field across the top dielectric, thus decreasing the unwanted parasitic electron injection from the gate during the erase operation. This will allow the cell to erase deep so to meet a basic requirement for Gigabit multilevel NAND memories. The introduction of high-k materials in the SONOS stack is unfortunately not straightforward. One problem is the Fermi-level pinning at the poly-Si/high-k interface. Another problem is the morphological changes the high-k material undergoes during the device fabrication thermal budget. These changes can modify the k-value and affect the band offset between gate and high-k material. The results may, in both cases, be the decrease of the barrier for electron injection from the gate and, as a consequence, the deterioration of the erase performance. In this paper we study the effect of gate material and of the morphological transformation associated with the high-k post deposition anneal on the erase and the retention behaviour of nitride-based cells. Two different high-k dielectrics are investigated: Al2O3 (which has already been found to be able to significantly improve the erase operation, guaranteeing at the same time excellent endurance and sufficient bake retention) and HfAlO. We show that both for Al2O3 and HfAlO a trade-off exists between erase and retention, higher PDA temperatures being beneficial for erase but detrimental for retention. We also discuss the effect of Fermi level pinning and poly-Si depletion on the erase behaviour and compare the erase performances of several PVD- and AVD-deposited metal gates.
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1071
Effect of Top Dielectric Morphology and Gate Material on the Performance of Nitride-based FLASH Memory Cells
The nitride-based SONOS cell, for its excellent scalability and process simplicity, is the candidate to push the scaling roadmap for FLASH memories beyond the limit imposed on floating-gate memories by the electrostatic interference between adjacent cells. The traditional SONOS cell consists of a nitride layer (the storage element) encapsulated by two SiO2 layers which isolate the nitride layer from the Si substrate and the poly-Si gate (Poly-Si/SiO2/Si3N4/SiO2/c-Si). However, the thick tunnel oxide necessary to meet the retention requirements imposes a severe limit on the erase performance because of the erase saturation phenomenon. One possibility to guarantee both the erase and the retention performance is the replacement of the top SiO2 layer with materials of higher dielectric constant (high-k dielectric). The presence of a high-k dielectric reduces the electric field across the top dielectric, thus decreasing the unwanted parasitic electron injection from the gate during the erase operation. This will allow the cell to erase deep so to meet a basic requirement for Gigabit multilevel NAND memories. The introduction of high-k materials in the SONOS stack is unfortunately not straightforward. One problem is the Fermi-level pinning at the poly-Si/high-k interface. Another problem is the morphological changes the high-k material undergoes during the device fabrication thermal budget. These changes can modify the k-value and affect the band offset between gate and high-k material. The results may, in both cases, be the decrease of the barrier for electron injection from the gate and, as a consequence, the deterioration of the erase performance. In this paper we study the effect of gate material and of the morphological transformation associated with the high-k post deposition anneal on the erase and the retention behaviour of nitride-based cells. Two different high-k dielectrics are investigated: Al2O3 (which has already been found to be able to significantly improve the erase operation, guaranteeing at the same time excellent endurance and sufficient bake retention) and HfAlO. We show that both for Al2O3 and HfAlO a trade-off exists between erase and retention, higher PDA temperatures being beneficial for erase but detrimental for retention. We also discuss the effect of Fermi level pinning and poly-Si depletion on the erase behaviour and compare the erase performances of several PVD- and AVD-deposited metal gates.
- 1 January 2007
- Published by Springer Nature in MRS Proceedings
- Vol. 1026
Strain measurements in s-Si/SiGe nanostructures by quantitative high-resolution electron microscopy
We have studied strained Si layers grown on Si1-xGex virtual substrate (VS) by high-resolution transmission electron microscopy (HRTEM). Aberration-corrected HRTEM coupled with geometric phase analysis (GPA) provides precise measurements of strain. Different parameters are investigated: the VS composition (x=20, 30, 40 and 50%) and the s-Si layer thickness. Finite element method simulations confirm our measurements. Measurements and simulations lead to the conclusion that the strain state of the deposited layer is independent of the layer thickness. We apply the technique to measuring strains in the channel region of a p-MOSFET and show that the technique is a promising metrological tool for nanoelectronic devices.
- 1 January 2007
- Published by Springer Nature in MRS Proceedings
- Vol. 1026
Strain measurements in s-Si/SiGe nanostructures by quantitative high-resolution electron microscopy
We have studied strained Si layers grown on Si1-xGex virtual substrate (VS) by high-resolution transmission electron microscopy (HRTEM). Aberration-corrected HRTEM coupled with geometric phase analysis (GPA) provides precise measurements of strain. Different parameters are investigated: the VS composition (x=20, 30, 40 and 50%) and the s-Si layer thickness. Finite element method simulations confirm our measurements. Measurements and simulations lead to the conclusion that the strain state of the deposited layer is independent of the layer thickness. We apply the technique to measuring strains in the channel region of a p-MOSFET and show that the technique is a promising metrological tool for nanoelectronic devices.
- 1 May 1999
- Published by Elsevier in Applied Surface Science
- Vol. 147 (1-4) , 187-200
Morphological properties of porous-Si layers for n+-emitter applications
- 1 May 1999
- Published by Elsevier in Applied Surface Science
- Vol. 147 (1-4) , 187-200
Morphological properties of porous-Si layers for n+-emitter applications
- 1 January 1995
- Published by Springer Nature in MRS Proceedings
- Vol. 402
Structural Characterization of Ion Beam Synthesized Epitaxial ErSi2-x Layers
The results are discussed of the characterization by means of TEM, RBS and XRD of ErSi2-x layers prepared by ion beam synthesis on (111) silicon. It will be shown that high quality (buried) layers can be prepared by channelled implantation of the erbium, whereas unchannelled implantation leads to discontinuous polycrystalline surface layers. The epitaxial growth and vacancy ordering in the silicide are discussed.
- 1 January 1995
- Published by Springer Nature in MRS Proceedings
- Vol. 402
Structural Characterization of Ion Beam Synthesized Epitaxial ErSi2-x Layers
The results are discussed of the characterization by means of TEM, RBS and XRD of ErSi2-x layers prepared by ion beam synthesis on (111) silicon. It will be shown that high quality (buried) layers can be prepared by channelled implantation of the erbium, whereas unchannelled implantation leads to discontinuous polycrystalline surface layers. The epitaxial growth and vacancy ordering in the silicide are discussed.
- 1 January 1995
- Published by Springer Nature in MRS Proceedings
- Vol. 402
Characterization of Ultra-Thin PtSi Films for Infrared Detectors
Transmission electron microscopy and grazing incidence X-ray diffraction are used for the structural characterization of ultra-thin PtSi layers on (100) silicon prepared by a two-step rapid thermal annealing process. The roughness of the layers is investigated with atomic force microscopy. Two deposition techniques for the initial Pt layer are compared.
- 1 January 1995
- Published by Springer Nature in MRS Proceedings
- Vol. 402
Characterization of Ultra-Thin PtSi Films for Infrared Detectors
Transmission electron microscopy and grazing incidence X-ray diffraction are used for the structural characterization of ultra-thin PtSi layers on (100) silicon prepared by a two-step rapid thermal annealing process. The roughness of the layers is investigated with atomic force microscopy. Two deposition techniques for the initial Pt layer are compared.