Seiki Miyata
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Seiki Miyata has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Akira Ibi
National Institute of Advanced Industrial Science and Technology, Tsukuba, Japan
6 shared publications - Yuh Shiohara
International Superconductivity Technology Center, Tokyo, Japan
5 shared publications H. Fukushima
2 shared publications- Masaya Konishi
Nagoya Coated Conductor Center, Superconductivity Research Laboratory, ISTEC, 2-4-1, Mutsuno, Atsuta-ku, Nagoya 456-8587, Japan
2 shared publications Teruo Izumi
2 shared publicationsY. Yamada
2 shared publications
Latest Publications
- 1 June 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (11) , 113922
Surface roughness of MgO thin film and its critical thickness for optimal biaxial texturing by ion-beam-assisted deposition
We investigated the deposition time dependences of the in-plane grain alignment ( ) and the surface roughness ( ) of biaxially textured MgO thin films fabricated by ion-beam-assisted deposition (IBAD) and found a strong correlation between them. The time evolution of the surface roughness of IBAD-MgO showed an abrupt increase at the same time corresponding to the beginning of the deterioration in . The roughness versus thickness profiles obtained under different deposition conditions with different assisting ion-beam currents collapsed to a single curve, even though the deposition rates were significantly different in each condition. This implies that the abrupt increase in roughness occurred at the same thickness—of about 4 nm—irrespective of the deposition rate. The result also indicated that the deterioration began with the same thickness of about 4 nm. This “critical” thickness of about 4 nm might be related to the completion of the crystallization of the film. Further, deposition beyond the critical thickness, therefore, became merely a homoepitaxial deposition under the “IBAD” condition, which was far from optimal because of the ion bombardment and low temperature (no-heating), and thus deteriorated. Based on these considerations, we propose an approach to attain a sharp texture in a IBAD-MgO-based biaxial substrate; moreover, we demonstrated this approach using a two-step deposition process.- 1 June 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (11) , 113922
Surface roughness of MgO thin film and its critical thickness for optimal biaxial texturing by ion-beam-assisted deposition
We investigated the deposition time dependences of the in-plane grain alignment ( ) and the surface roughness ( ) of biaxially textured MgO thin films fabricated by ion-beam-assisted deposition (IBAD) and found a strong correlation between them. The time evolution of the surface roughness of IBAD-MgO showed an abrupt increase at the same time corresponding to the beginning of the deterioration in . The roughness versus thickness profiles obtained under different deposition conditions with different assisting ion-beam currents collapsed to a single curve, even though the deposition rates were significantly different in each condition. This implies that the abrupt increase in roughness occurred at the same thickness—of about 4 nm—irrespective of the deposition rate. The result also indicated that the deterioration began with the same thickness of about 4 nm. This “critical” thickness of about 4 nm might be related to the completion of the crystallization of the film. Further, deposition beyond the critical thickness, therefore, became merely a homoepitaxial deposition under the “IBAD” condition, which was far from optimal because of the ion bombardment and low temperature (no-heating), and thus deteriorated. Based on these considerations, we propose an approach to attain a sharp texture in a IBAD-MgO-based biaxial substrate; moreover, we demonstrated this approach using a two-step deposition process.- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 3119-3122
Development of TFA-MOD Process for Coated Conductors in Japan
Progresses in the development of the TFA-MOD process for the coated conductors in Japan are reviewed. In the fundamental approaches, some important advantages of Ba-poor starting solution were found such as for obtaining higher Jc, shorter reaction time and wider process temperature window. The high Ic value of 735 A/cm-w@77 K was attained. Additionally, introduction of artificial pinning centers by Sm-substitution and Zr-addition to the Ba-poor films was successfully investigated. The films showed a high minimum Ic value of 42 A/cm-w at 77 K, 1 T. Furthermore, isotropic Ic properties in the angular dependence of applied magnetic fields was realized by the uniform distribution of nanoprticles of Zr-compound. On the other hand, two different process of MOD including batch and reel-to-reel (RTR) types have been developed as an engineering process for low cost and long tape production with high superconducting performances at a high rate. In the batch type, long tape synthesis process could be developed by the optimization of the growth conditions in a large furnace. A 500 m long tape was heat-treated and a high Ic value of 310 A/cm-w in a 250 m tape was confirmed. Concerning the RTR type, a high production rate system was developed after confirmation of the ability of the continuous process in a 90 m long tape. A multi-turn with a vertical gas flow system was developed for this purpose. This system was applied to the fabrication of superconducting films on the lower cost buffer layers including a high deposition rate IBAD-MgO layer. Currently, a 5 m long tape with 250 A/cm-w was obtained at the production rate of 3 m/h using a part of the multi-turn system, which is equivalent to 15 m/h in the entire use of the furnace.
- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 3119-3122
Development of TFA-MOD Process for Coated Conductors in Japan
Progresses in the development of the TFA-MOD process for the coated conductors in Japan are reviewed. In the fundamental approaches, some important advantages of Ba-poor starting solution were found such as for obtaining higher Jc, shorter reaction time and wider process temperature window. The high Ic value of 735 A/cm-w@77 K was attained. Additionally, introduction of artificial pinning centers by Sm-substitution and Zr-addition to the Ba-poor films was successfully investigated. The films showed a high minimum Ic value of 42 A/cm-w at 77 K, 1 T. Furthermore, isotropic Ic properties in the angular dependence of applied magnetic fields was realized by the uniform distribution of nanoprticles of Zr-compound. On the other hand, two different process of MOD including batch and reel-to-reel (RTR) types have been developed as an engineering process for low cost and long tape production with high superconducting performances at a high rate. In the batch type, long tape synthesis process could be developed by the optimization of the growth conditions in a large furnace. A 500 m long tape was heat-treated and a high Ic value of 310 A/cm-w in a 250 m tape was confirmed. Concerning the RTR type, a high production rate system was developed after confirmation of the ability of the continuous process in a 90 m long tape. A multi-turn with a vertical gas flow system was developed for this purpose. This system was applied to the fabrication of superconducting films on the lower cost buffer layers including a high deposition rate IBAD-MgO layer. Currently, a 5 m long tape with 250 A/cm-w was obtained at the production rate of 3 m/h using a part of the multi-turn system, which is equivalent to 15 m/h in the entire use of the furnace.
- 5 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 3236-3239
Development of Long Length IBAD-MgO and PLD Coated Conductors
For high speed and low cost production of coated conductors, a simplified 4-layered buffer architecture consisting of Gd2Zr2O7 (GZO)/Ion Beam Assisted Deposition (IBAD)-MgO/LaMnO3/CeO2 was realized, which is compared with the conventional 5-layered IBAD-MgO buffer layers. A new cation diffusion barrier and nucleation GZO layer was first reported. The fourth layer of Pulsed Laser Deposition (PLD)-CeO2 showing the self-epitaxial growth effect resulted in the in-plane texturing (Deltaphi) of about 3 to 4 degrees. Consequently, high critical current, Ic, values above 600 A/cm-width were attained for PLD-GdBa2Cu3O7-X (GdBCO) short samples. Using this result, a 41 m long GdBCO coated conductors was successfully fabricated at the production rate of 24 m/h for IBAD-MgO. This conductor exhibited superior Deltaphi values of 3.7 to 3.8 degrees and high Ic values of 500 to 600 A/cm-width at 77 K and self -field (s.f.) along almost the entire length. The highest Ic recorded 608 A/cm-width with the Jc value of 2.43 Ma/hboxcm2. Furthermore, a new IBAD-MgO deposition method was developed, using DC-reactive sputtering which is expected to be inexpensive and easy to scale up. This system brought about a high production rate of 150 m/h in spite of the small deposition area (6 times 20 cm2). The GdBCO on this buffered substrate also showed a high Ic value of 286 A/cm-width at 77 K and s.f., corresponding to the Jc value of 1.43 Ma/hboxcm2.
- 5 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 3236-3239
Development of Long Length IBAD-MgO and PLD Coated Conductors
For high speed and low cost production of coated conductors, a simplified 4-layered buffer architecture consisting of Gd2Zr2O7 (GZO)/Ion Beam Assisted Deposition (IBAD)-MgO/LaMnO3/CeO2 was realized, which is compared with the conventional 5-layered IBAD-MgO buffer layers. A new cation diffusion barrier and nucleation GZO layer was first reported. The fourth layer of Pulsed Laser Deposition (PLD)-CeO2 showing the self-epitaxial growth effect resulted in the in-plane texturing (Deltaphi) of about 3 to 4 degrees. Consequently, high critical current, Ic, values above 600 A/cm-width were attained for PLD-GdBa2Cu3O7-X (GdBCO) short samples. Using this result, a 41 m long GdBCO coated conductors was successfully fabricated at the production rate of 24 m/h for IBAD-MgO. This conductor exhibited superior Deltaphi values of 3.7 to 3.8 degrees and high Ic values of 500 to 600 A/cm-width at 77 K and self -field (s.f.) along almost the entire length. The highest Ic recorded 608 A/cm-width with the Jc value of 2.43 Ma/hboxcm2. Furthermore, a new IBAD-MgO deposition method was developed, using DC-reactive sputtering which is expected to be inexpensive and easy to scale up. This system brought about a high production rate of 150 m/h in spite of the small deposition area (6 times 20 cm2). The GdBCO on this buffered substrate also showed a high Ic value of 286 A/cm-width at 77 K and s.f., corresponding to the Jc value of 1.43 Ma/hboxcm2.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3371-3374
GdBaCuO and YBaCuO Long Coated Conductors by IBAD-PLD Method—Enhancement of Production Speed and Critical Current in a Magnetic Field
We have been developing long coated conductors with high critical current, Ic, by multi-plume and multi-turn pulsed laser deposition (MPMT-PLD) method. In addition to YBa2Cu3O7-X (YBCO) coated conductors, we have recently succeeded in fabricating long GdBa2Cu3O7-X (GdBCO) coated conductors. The 30 m long and 60 m long GdBCO conductors showed higher Jc values in a magnetic field and lower anisotropy than the conventional long YBCO conductor. Critical current, Ic, of the GdBCO at 3 T and 77 K was more than 20 A, which was three times larger than that of the YBCO long coated conductor. To demonstrate the high performance of GdBCO, we fabricated GdBCO coils and compared it with the YBCO coil. The GdBCO coil was successfully energized up to large Ic's of 74.2 A and 184.8 A at 77 K and 64 K, which generated magnetic field of 0.5 T and 1.2 T at 64 K and 77 K. We confirmed that the GdBCO conductor is more promising than the YBCO conductor for the application because its superior transport properties in a magnetic field.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3371-3374
GdBaCuO and YBaCuO Long Coated Conductors by IBAD-PLD Method—Enhancement of Production Speed and Critical Current in a Magnetic Field
We have been developing long coated conductors with high critical current, Ic, by multi-plume and multi-turn pulsed laser deposition (MPMT-PLD) method. In addition to YBa2Cu3O7-X (YBCO) coated conductors, we have recently succeeded in fabricating long GdBa2Cu3O7-X (GdBCO) coated conductors. The 30 m long and 60 m long GdBCO conductors showed higher Jc values in a magnetic field and lower anisotropy than the conventional long YBCO conductor. Critical current, Ic, of the GdBCO at 3 T and 77 K was more than 20 A, which was three times larger than that of the YBCO long coated conductor. To demonstrate the high performance of GdBCO, we fabricated GdBCO coils and compared it with the YBCO coil. The GdBCO coil was successfully energized up to large Ic's of 74.2 A and 184.8 A at 77 K and 64 K, which generated magnetic field of 0.5 T and 1.2 T at 64 K and 77 K. We confirmed that the GdBCO conductor is more promising than the YBCO conductor for the application because its superior transport properties in a magnetic field.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3406-3408
Single-Buffer-Architectured Coated Conductor Based on IBAD and PLD Method
In order to lower the production costs of coated conductors based on the ion-beam assisted deposition (IBAD) and pulsed laser deposition (PLD) method, we examined a single-buffered architecture (REBCO/IBAD/Hastelloy) without a second buffer layer of . While all samples exhibited similar degrees of the textures, transport current properties were found to be strongly dependent on the REBCO layer and IBAD template materials. With a structure of Ag/PLD-GdBa2Cu3O7/IBAD - Gd2Zr2O7/Hastelloy, we obtained critical currents of 165 Amps (0.8 -thick) and critical current densities of 3.4 (0.4 -thick) for short-piece samples in standard four-probe dc measurements.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3406-3408
Single-Buffer-Architectured Coated Conductor Based on IBAD and PLD Method
In order to lower the production costs of coated conductors based on the ion-beam assisted deposition (IBAD) and pulsed laser deposition (PLD) method, we examined a single-buffered architecture (REBCO/IBAD/Hastelloy) without a second buffer layer of . While all samples exhibited similar degrees of the textures, transport current properties were found to be strongly dependent on the REBCO layer and IBAD template materials. With a structure of Ag/PLD-GdBa2Cu3O7/IBAD - Gd2Zr2O7/Hastelloy, we obtained critical currents of 165 Amps (0.8 -thick) and critical current densities of 3.4 (0.4 -thick) for short-piece samples in standard four-probe dc measurements.
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 946
Investigation of In-Field Properties of YBCO Film with Artificial Pinning Centers
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 946
Investigation of In-Field Properties of YBCO Film with Artificial Pinning Centers