Adam Cywar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adam Cywar has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Helena Silva
Department of Electrical and Computer Engineering, University of Connecticut , Storrs, Connecticut 06269, USA
5 shared publications - Ali Gokirmak
University of Connecticut, Electrical & Computer Engineering, Storrs, Connecticut, United States
3 shared publications - Gokhan Bakan
UNAM-Institute of Materials Science and Nanotechnology, Bilkent University, Ankara 06800, Turkey
3 shared publications - Ali Gokirmak
Electrical and Computer Engineering University of Connecticut Storrs CT 06269‐4157 USA
1 shared publication - Anna Gorbenko
Department of Electrical and Computer Engineering, University of Connecticut, Storrs, CT, USA
1 shared publication Chung Lam
1 shared publication
Latest Publications
- 30 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 20 (1536125X) , 75-82
Reset Variability in Phase Change Memory for Hardware Security Applications
The rapid quench from melt associated with the reset operation in phase change memory is a suitable physical process to leverage programming variability for hardware security. We have experimentally characterized cell-to-cell programming variability in Ge2Sb2Te5 (GST) line cells using a single reset voltage pulse with moderate amplitude. We have observed that the cell dimensions and programming pulse parameters play a critical role on the programming variability. Cells with larger length-to-width ratios (L/W 1.8) show greater programming variability when moderate reset voltage amplitudes (Vappl) are applied. This variability is further increased with shorter pulse edges (tedge) of the applied pulses. We have performed a study for a reset-variability-based physical unclonable function (PUF) with 85 cells (with L/W = 4) by applying identical single pulses with shorter tedge and a pre-calibrated Vappl. Cells are randomly programmed to the full reset (high-resistance-state or HRS), or the partial reset or set (low-resistance-state or LRS) states with an equal probability and the two states are separated by ~1.5 order of magnitude. No bit flipping is observed after 9 months of programming and instead, the separation increases to ~3 orders of magnitude because of the upward and downward resistance drift of the HRS and LRS states. The underlying physical mechanisms behind the enhanced variability are identified as thermal runaway at the onset of GST melting and the additional current overshoot due to the parasitic capacitances, based on the results obtained from COMSOL finite element simulations and SPICE circuit modeling of the experimental setup.
- 30 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 20 (1536125X) , 75-82
Reset Variability in Phase Change Memory for Hardware Security Applications
The rapid quench from melt associated with the reset operation in phase change memory is a suitable physical process to leverage programming variability for hardware security. We have experimentally characterized cell-to-cell programming variability in Ge2Sb2Te5 (GST) line cells using a single reset voltage pulse with moderate amplitude. We have observed that the cell dimensions and programming pulse parameters play a critical role on the programming variability. Cells with larger length-to-width ratios (L/W 1.8) show greater programming variability when moderate reset voltage amplitudes (Vappl) are applied. This variability is further increased with shorter pulse edges (tedge) of the applied pulses. We have performed a study for a reset-variability-based physical unclonable function (PUF) with 85 cells (with L/W = 4) by applying identical single pulses with shorter tedge and a pre-calibrated Vappl. Cells are randomly programmed to the full reset (high-resistance-state or HRS), or the partial reset or set (low-resistance-state or LRS) states with an equal probability and the two states are separated by ~1.5 order of magnitude. No bit flipping is observed after 9 months of programming and instead, the separation increases to ~3 orders of magnitude because of the upward and downward resistance drift of the HRS and LRS states. The underlying physical mechanisms behind the enhanced variability are identified as thermal runaway at the onset of GST melting and the additional current overshoot due to the parasitic capacitances, based on the results obtained from COMSOL finite element simulations and SPICE circuit modeling of the experimental setup.
- 10 May 2012
- Published by IOP Publishing in Nanotechnology
- Vol. 23 (22) , 225201
The impact of heater-recess and load matching in phase change memory mushroom cells
Two-dimensional finite element simulations with rotational symmetry are used to analyze the impact of the bottom electrode recess on the reset operation of phase change memory elements with mushroom cell geometry (Ge2Sb2Te5 (GST) film over a patterned TiN pillar). Temperature dependent materials parameters are used for GST and TiN, and the latent heat of fusion in melting of GST is included to model melting. The results of this study indicate that a lower reset current and a more favorable thermal profile may be achieved by extending the active region of GST down into the pillar, due to the heat confinement. It is shown that the current through cells with an insufficient load condition for maximum power transfer can be maintained at a level lower than that which is sufficient for reset operation for extended periods of time due to the non-linear nature of temperature dependent electrical conductivity of GST. These results suggest that if the load condition is not matched, excessive voltage levels or pulse durations would be necessary to achieve successful reset operation across cell arrays.
- 10 May 2012
- Published by IOP Publishing in Nanotechnology
- Vol. 23 (22) , 225201
The impact of heater-recess and load matching in phase change memory mushroom cells
Two-dimensional finite element simulations with rotational symmetry are used to analyze the impact of the bottom electrode recess on the reset operation of phase change memory elements with mushroom cell geometry (Ge2Sb2Te5 (GST) film over a patterned TiN pillar). Temperature dependent materials parameters are used for GST and TiN, and the latent heat of fusion in melting of GST is included to model melting. The results of this study indicate that a lower reset current and a more favorable thermal profile may be achieved by extending the active region of GST down into the pillar, due to the heat confinement. It is shown that the current through cells with an insufficient load condition for maximum power transfer can be maintained at a level lower than that which is sufficient for reset operation for extended periods of time due to the non-linear nature of temperature dependent electrical conductivity of GST. These results suggest that if the load condition is not matched, excessive voltage levels or pulse durations would be necessary to achieve successful reset operation across cell arrays.
- 7 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 31 (12) , 1362-1364
Nanosecond Pulse Generation in a Silicon Microwire
We report the generation of trapezoidal current pulses by applying a dc voltage to a single nanocrystalline silicon microwire through a load. The wire is expected to be physically disconnecting and reconnecting at a constriction near its midpoint as a result of volume change in repeated solid-liquid phase transitions. A scanning electron microscope image and the wire's electrical characteristics suggest that the wire is partially molten at the time of disconnection. The current pulses rise from 0 to 7 mA and have widths of 13.48 ± 0.65 ns, a repetition rate of 9.12 ± 0.06 MHz, rise/fall times ≤ 350 ps, a peak power density of ~1.9 kW/mm2, and a very consistent pulse shape.
- 7 October 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 31 (12) , 1362-1364
Nanosecond Pulse Generation in a Silicon Microwire
We report the generation of trapezoidal current pulses by applying a dc voltage to a single nanocrystalline silicon microwire through a load. The wire is expected to be physically disconnecting and reconnecting at a constriction near its midpoint as a result of volume change in repeated solid-liquid phase transitions. A scanning electron microscope image and the wire's electrical characteristics suggest that the wire is partially molten at the time of disconnection. The current pulses rise from 0 to 7 mA and have widths of 13.48 ± 0.65 ns, a repetition rate of 9.12 ± 0.06 MHz, rise/fall times ≤ 350 ps, a peak power density of ~1.9 kW/mm2, and a very consistent pulse shape.
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1178
Measurements of Liquid Silicon Resistivity on Silicon Microwires
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1178
Measurements of Liquid Silicon Resistivity on Silicon Microwires
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1144
Annealing of Nanocrystalline Silicon Micro-bridges with Electrical Stress
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1144
Annealing of Nanocrystalline Silicon Micro-bridges with Electrical Stress