Yu-Yuan Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yu-Yuan Lin has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Kuo‐Chun Chang
National Taiwan University
2 shared publicationsEduardo Miranda
Department of Civil and Environmental Engineering, Stanford University, Stanford, CA, U.S.A.
1 shared publicationKuo-Chun Chang
Department of Civil Engineering, National Taiwan University, Taipei, Taiwan
1 shared publicationKuo-Chung Chang
Department of Civil Engineering, National Taiwan University, Taipei 106, Taiwan
1 shared publicationTsai-Fu Chuang
Department of Landscape Architecture, Mingdao University, Changhua 523, Taiwan
1 shared publicationYuan‐Li Wang
Department of Civil Engineering, National Taiwan University, Taipei 106, Taiwan
1 shared publication
Latest Publications
- 1 June 2005
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 34 (11) , 1427-1443
Evaluation of damping reduction factors for estimating elastic response of structures with high damping
- 1 June 2005
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 34 (11) , 1427-1443
Evaluation of damping reduction factors for estimating elastic response of structures with high damping
- 4 March 2005
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 28 (2) , 293-303
On the non‐iterative procedure of direct displacement‐based seismic design for portal R.C. bridges: Using inelastic design spectrum
In general, iterative procedures are required by the direct displacement‐based seismic design method. This paper presents a non‐iterative displacement‐based method for the design of portal R.C. bridges based on the inelastic design response spectrum. By combining the properties of structural stiffness and yielding, a rational, efficient and accurate method is established, where not only the strength and stiffness of members depend on the pre‐selected target displacement and ductility ratio, but the cross‐sections of those can also directly be determined form the two pre‐chosen values without any iteration. In addition to the examples that are used to illustrate the proposed procedure, the dynamic inelastic time history analysis and the static nonlinear analysis (pushover analysis) are also included to verify this procedure. It is concluded by the study that iterations are not needed in direct displacement‐based design if the force‐deformation relationships of designed structures can be derived.
- 4 March 2005
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 28 (2) , 293-303
On the non‐iterative procedure of direct displacement‐based seismic design for portal R.C. bridges: Using inelastic design spectrum
In general, iterative procedures are required by the direct displacement‐based seismic design method. This paper presents a non‐iterative displacement‐based method for the design of portal R.C. bridges based on the inelastic design response spectrum. By combining the properties of structural stiffness and yielding, a rational, efficient and accurate method is established, where not only the strength and stiffness of members depend on the pre‐selected target displacement and ductility ratio, but the cross‐sections of those can also directly be determined form the two pre‐chosen values without any iteration. In addition to the examples that are used to illustrate the proposed procedure, the dynamic inelastic time history analysis and the static nonlinear analysis (pushover analysis) are also included to verify this procedure. It is concluded by the study that iterations are not needed in direct displacement‐based design if the force‐deformation relationships of designed structures can be derived.
- 17 May 2004
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 33 (9) , 1059-1066
A mathematical basis for the convergence of the capacity spectrum method
- 17 May 2004
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 33 (9) , 1059-1066
A mathematical basis for the convergence of the capacity spectrum method
- 7 November 2003
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 33 (1) , 35-48
Comparison of displacement coefficient method and capacity spectrum method with experimental results of RC columns
For the performance‐based seismic design of buildings, both the displacement coefficient method used by FEMA‐273 and the capacity spectrum method adopted by ATC‐40 are non‐linear static procedures. The pushover curves of structures need to be established during processing of these two methods. They are applied to evaluation and rehabilitation of existing structures. This paper is concerned with experimental studies on the accuracy of both methods. Through carrying out the pseudo‐dynamic tests, cyclic loading tests and pushover tests on three reinforced concrete (RC) columns, the maximum inelastic deformation demands (target displacements) determined by the coefficient method of FEMA‐273 and the capacity spectrum method of ATC‐40 are compared. In addition, a modified capacity spectrum method which is based on the use of inelastic design response spectra is also included in this study. It is shown from the test specimens that the coefficient method overestimates the peak test displacements with an average error of +28% while the capacity spectrum method underestimates them with an average error of ‐20%. If the Kowalsky hysteretic damping model is used in the capacity spectrum method instead of the original damping model, the average errors become ‐11% by ignoring the effect of stiffness degrading and ‐1.2% by slightly including the effect of stiffness degrading. Furthermore, if the Newmark–Hall inelastic design spectrum is implemented in the capacity spectrum method instead of the elastic design spectrum, the average error decreases to ‐6.6% which undervalues, but is close to, the experimental results. Copyright © 2003 John Wiley & Sons, Ltd.
- 7 November 2003
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 33 (1) , 35-48
Comparison of displacement coefficient method and capacity spectrum method with experimental results of RC columns
For the performance‐based seismic design of buildings, both the displacement coefficient method used by FEMA‐273 and the capacity spectrum method adopted by ATC‐40 are non‐linear static procedures. The pushover curves of structures need to be established during processing of these two methods. They are applied to evaluation and rehabilitation of existing structures. This paper is concerned with experimental studies on the accuracy of both methods. Through carrying out the pseudo‐dynamic tests, cyclic loading tests and pushover tests on three reinforced concrete (RC) columns, the maximum inelastic deformation demands (target displacements) determined by the coefficient method of FEMA‐273 and the capacity spectrum method of ATC‐40 are compared. In addition, a modified capacity spectrum method which is based on the use of inelastic design response spectra is also included in this study. It is shown from the test specimens that the coefficient method overestimates the peak test displacements with an average error of +28% while the capacity spectrum method underestimates them with an average error of ‐20%. If the Kowalsky hysteretic damping model is used in the capacity spectrum method instead of the original damping model, the average errors become ‐11% by ignoring the effect of stiffness degrading and ‐1.2% by slightly including the effect of stiffness degrading. Furthermore, if the Newmark–Hall inelastic design spectrum is implemented in the capacity spectrum method instead of the elastic design spectrum, the average error decreases to ‐6.6% which undervalues, but is close to, the experimental results. Copyright © 2003 John Wiley & Sons, Ltd.