Caihua Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Caihua Liu has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Chaoyi Sun
State Key Laboratory of Geomechanics and Geotechnical Engineering, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan 430071, China
3 shared publications - Kai Fan
State Key Laboratory of Geomechanics and Geotechnical Engineering Safety, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan, China
2 shared publications - Chao Guo
College of Geology & Environment, Xi’an University of Science and Technology, Xi’an 710054, China
1 shared publication Cong-Xin Chen
Chinese Academy of Sciences
1 shared publicationCongxin Chen
1 shared publicationHongqiang Li
PowerChina Chengdu Engineering Corporation Limited 610072 Chengdu Sichuan China
1 shared publication
Latest Publications
- Open Access
- 6 August 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (15) , 2617
Landslide Susceptibility Evaluation Based on Deep Learning and Imbalanced Sampling at Multi-Scale
The main objective of the present study was to conduct landslide susceptibility assessment and zoning analysis based on multi-scale imbalanced sampling and deep learning methods. Jiangkou Town, China, was selected as the study area. Grid cells with resolutions of 12.5 m, 25 m, and 50 m were chosen. Imbalanced sampling was applied using landslide/non-landslide ratios of 1:1, 1:2, and 1:3 to construct multi-scale modeling datasets. Susceptibility conditioning factors were screened using the frequency ratio (FR), Pearson correlation coefficient, and multicollinearity diagnostics and nine factors were obtained: slope, aspect, plane curvature, profile curvature, lithology, distance to river, distance to fault, annual rainfall, and land use. Six models—Logistic Model Tree (LMT), Kernel Logistic Regression (KLR), EfficientNet, ResNet, Transformer, and U-Net—were selected to establish 54 susceptibility evaluation models under various combinations of resolution and sampling ratios. The predictive reliability of the models was evaluated using receiver operating characteristic (ROC) curves and Kappa coefficients. Among the evaluated configurations, ResNet at a 12.5 m resolution with a 1:3 sampling ratio was retained as the preferred overall mapping configuration. It achieved a validation AUC of 0.963 and a Kappa coefficient of 0.778, together with strong susceptibility-zonation selectivity. The highest individual Kappa coefficient (0.819) was obtained by ResNet at a 25 m resolution with a 1:3 sampling ratio. Thus, the preferred configuration was identified through an integrated interpretation of the validation AUC, Kappa agreement, and susceptibility-zonation performance rather than by maximizing a single metric. The landslide susceptibility maps produced were classified into five levels and validated using the landslide distribution, landslide density and frequency ratio within each susceptibility zone. Most models showed good predictive performance in areas characterized by very high and very low susceptibility. According to the results of the comparison of the different susceptibility levels, it appears that ResNet and EfficientNet produced the most similar spatial predictions, while ResNet and Transformer presented the largest deviations. The deviations are mainly located near river valleys and areas with intense human activity. The proposed methodological framework and results can support disaster prevention, land-use planning, and regional risk management, particularly in mountainous areas with complex geological and topographic conditions.
- 6 August 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (15) , 2617
Open AccessLandslide Susceptibility Evaluation Based on Deep Learning and Imbalanced Sampling at Multi-Scale
The main objective of the present study was to conduct landslide susceptibility assessment and zoning analysis based on multi-scale imbalanced sampling and deep learning methods. Jiangkou Town, China, was selected as the study area. Grid cells with resolutions of 12.5 m, 25 m, and 50 m were chosen. Imbalanced sampling was applied using landslide/non-landslide ratios of 1:1, 1:2, and 1:3 to construct multi-scale modeling datasets. Susceptibility conditioning factors were screened using the frequency ratio (FR), Pearson correlation coefficient, and multicollinearity diagnostics and nine factors were obtained: slope, aspect, plane curvature, profile curvature, lithology, distance to river, distance to fault, annual rainfall, and land use. Six models—Logistic Model Tree (LMT), Kernel Logistic Regression (KLR), EfficientNet, ResNet, Transformer, and U-Net—were selected to establish 54 susceptibility evaluation models under various combinations of resolution and sampling ratios. The predictive reliability of the models was evaluated using receiver operating characteristic (ROC) curves and Kappa coefficients. Among the evaluated configurations, ResNet at a 12.5 m resolution with a 1:3 sampling ratio was retained as the preferred overall mapping configuration. It achieved a validation AUC of 0.963 and a Kappa coefficient of 0.778, together with strong susceptibility-zonation selectivity. The highest individual Kappa coefficient (0.819) was obtained by ResNet at a 25 m resolution with a 1:3 sampling ratio. Thus, the preferred configuration was identified through an integrated interpretation of the validation AUC, Kappa agreement, and susceptibility-zonation performance rather than by maximizing a single metric. The landslide susceptibility maps produced were classified into five levels and validated using the landslide distribution, landslide density and frequency ratio within each susceptibility zone. Most models showed good predictive performance in areas characterized by very high and very low susceptibility. According to the results of the comparison of the different susceptibility levels, it appears that ResNet and EfficientNet produced the most similar spatial predictions, while ResNet and Transformer presented the largest deviations. The deviations are mainly located near river valleys and areas with intense human activity. The proposed methodological framework and results can support disaster prevention, land-use planning, and regional risk management, particularly in mountainous areas with complex geological and topographic conditions.
- Open Access
- 19 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 22
Stability Analysis Approach to Block Toppling in Rock Slopes Under Seismic Loads
Rock slope toppling failure is a typical type of slope disaster. It is crucial for engineering practice to quickly and accurately evaluate the toppling stability of rock slopes under seismic loads. Based on Liu’s pseudo-continuous medium method, the geomechanical model for evaluating the stability of rock slope block toppling subjected to seismic loads, considering non-orthogonal characteristics of the structural planes, is established, and the analytical solution for toppling failure is proposed. The relationship between the normal and shear stresses acting at the block base is discussed, and the formula for determining the location of the failure mode transition point in different cases is deduced. Through programmed analysis, the impact of the seismic load on slope stability and the influence of key parameters on the critical seismic influence coefficient are systematically investigated. The research results indicate that the seismic load has a significant impact on slope stability. With increases in the seismic influence coefficient, or decreases in the angle between the seismic load and the horizontal plane, the supporting force required for slope stability increases, and the transition point from toppling to sliding moves towards the slope toe. It is also shown that, when the seismic influence coefficient reaches the critical value, the slope will slide as a whole without toppling. The value of the critical seismic influence coefficient is positively correlated with the internal friction angle of the block base, and negatively correlated with the direction of the seismic load, the internal friction angle of the block side and the dip angle of the block base. This study provides theoretical support for evaluating the block toppling stability of slopes in seismic-prone areas.
- 19 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 22
Open AccessStability Analysis Approach to Block Toppling in Rock Slopes Under Seismic Loads
Rock slope toppling failure is a typical type of slope disaster. It is crucial for engineering practice to quickly and accurately evaluate the toppling stability of rock slopes under seismic loads. Based on Liu’s pseudo-continuous medium method, the geomechanical model for evaluating the stability of rock slope block toppling subjected to seismic loads, considering non-orthogonal characteristics of the structural planes, is established, and the analytical solution for toppling failure is proposed. The relationship between the normal and shear stresses acting at the block base is discussed, and the formula for determining the location of the failure mode transition point in different cases is deduced. Through programmed analysis, the impact of the seismic load on slope stability and the influence of key parameters on the critical seismic influence coefficient are systematically investigated. The research results indicate that the seismic load has a significant impact on slope stability. With increases in the seismic influence coefficient, or decreases in the angle between the seismic load and the horizontal plane, the supporting force required for slope stability increases, and the transition point from toppling to sliding moves towards the slope toe. It is also shown that, when the seismic influence coefficient reaches the critical value, the slope will slide as a whole without toppling. The value of the critical seismic influence coefficient is positively correlated with the internal friction angle of the block base, and negatively correlated with the direction of the seismic load, the internal friction angle of the block side and the dip angle of the block base. This study provides theoretical support for evaluating the block toppling stability of slopes in seismic-prone areas.
- 3 September 2025
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 84 (10) , 1-29
Deformation behaviors and failure mechanisms of fully grouted bolts in jointed rock masses under coupled tension and shear
- 3 September 2025
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 84 (10) , 1-29
Deformation behaviors and failure mechanisms of fully grouted bolts in jointed rock masses under coupled tension and shear
- Open Access
- 1 August 2025
- Published by China Science Publishing & Media Ltd. in Chinese Journal of Rock Mechanics and Engineering
- Vol. 44 (8) , 2101-2111
地震作用下隐伏顺层岩质边坡稳定性上限分析
Earthquakes play a critical role in the catastrophic destabilization of concealed bedding rock slopes (CBRSs). However, established methods for assessing the stability of these slopes under seismic conditions are lacking. This study proposes a method for determining the pseudo-static coefficient by analyzing extensive results from shaking table model tests of CBRSs, which accounts for the peak acceleration amplification effect with elevation. Based on the shattering-sliding failure mechanisms of CBRSs under seismic loading, a double-slip model along with its kinematically admissible velocity field is developed. Utilizing the upper bound theorem of limit analysis, a stability analysis method for CBRSs subjected to seismic conditions is presented. Additionally, a comparative analysis of slope stability is conducted through two case studies, further validating the proposed method. The findings indicate that under seismic action, these slopes are particularly vulnerable to catastrophic sliding failure, exhibiting nonlinear and segmented characteristics in both the peak acceleration amplification effect and the surface amplification effect. As the amplitudes of horizontal and vertical seismic waves increase, the stability coefficient of the CBRSs decreases linearly, accompanied by a slight reduction in the thickness of the potential sliding mass. Notably, the stability coefficient exhibits a more significant decrease when accounting for the dynamic elevation amplification effect of seismic acceleration. Furthermore, the stability coefficient of CBRSs decreases as a power function in relation to increasing slope angle and height, while the thickness of the potential sliding mass decreases with an increasing slope angle but increases with rising slope height and structural plane strength. A comparative analysis between the proposed method and two case studies from the literature reveals strong agreement in the calculated results, thereby validating the accuracy and reliability of the method. These findings provide valuable insights for the stability evaluation and treatment design of CBRSs under seismic conditions.
- 1 August 2025
- Published by China Science Publishing & Media Ltd. in Chinese Journal of Rock Mechanics and Engineering
- Vol. 44 (8) , 2101-2111
Open Access地震作用下隐伏顺层岩质边坡稳定性上限分析
Earthquakes play a critical role in the catastrophic destabilization of concealed bedding rock slopes (CBRSs). However, established methods for assessing the stability of these slopes under seismic conditions are lacking. This study proposes a method for determining the pseudo-static coefficient by analyzing extensive results from shaking table model tests of CBRSs, which accounts for the peak acceleration amplification effect with elevation. Based on the shattering-sliding failure mechanisms of CBRSs under seismic loading, a double-slip model along with its kinematically admissible velocity field is developed. Utilizing the upper bound theorem of limit analysis, a stability analysis method for CBRSs subjected to seismic conditions is presented. Additionally, a comparative analysis of slope stability is conducted through two case studies, further validating the proposed method. The findings indicate that under seismic action, these slopes are particularly vulnerable to catastrophic sliding failure, exhibiting nonlinear and segmented characteristics in both the peak acceleration amplification effect and the surface amplification effect. As the amplitudes of horizontal and vertical seismic waves increase, the stability coefficient of the CBRSs decreases linearly, accompanied by a slight reduction in the thickness of the potential sliding mass. Notably, the stability coefficient exhibits a more significant decrease when accounting for the dynamic elevation amplification effect of seismic acceleration. Furthermore, the stability coefficient of CBRSs decreases as a power function in relation to increasing slope angle and height, while the thickness of the potential sliding mass decreases with an increasing slope angle but increases with rising slope height and structural plane strength. A comparative analysis between the proposed method and two case studies from the literature reveals strong agreement in the calculated results, thereby validating the accuracy and reliability of the method. These findings provide valuable insights for the stability evaluation and treatment design of CBRSs under seismic conditions.
- 1 October 2011
- Published by Springer Nature in Journal of Central South University
- Vol. 18 (5) , 1662-1666
A new apparatus for investigating stress, deformation and seepage coupling properties of rock fractures
- 1 October 2011
- Published by Springer Nature in Journal of Central South University
- Vol. 18 (5) , 1662-1666
A new apparatus for investigating stress, deformation and seepage coupling properties of rock fractures