José Luis Iturbe García
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
José Luis Iturbe García has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Elizabeth Teresita Romero-Guzmán
Departamento de Química, Instituto Nacional de Investigaciones Nucleares, Carretera México–Toluca s/n, La Marquesa, Ocoyoacac 52045, Estado de México, Mexico
3 shared publications Beatriz Eugenia López-Muñoz
2 shared publications- Héctor Hernández-Mendoza
Instituto de Investigación de Zonas Desérticas, Universidad Autónoma de San Luis Potosí, Altair 200, San Luís Potosí 78377, Mexico
2 shared publications - Liliana Romero Guzmán
Facultad de Arquitectura y Diseño, Universidad Autónoma del Estado de México
2 shared publications - Lázaro Raymundo Reyes Gutiérrez
Universidad Autónoma Metropolitana Unidad Lerma Avenida de las Garzas 10 Colonia El Panteón Lerma de Villada 52005 Estado de México C.P México
2 shared publications María de Jesús Marín Allende
2 shared publications
Latest Publications
- Open Access
Preparation of AlLi Alloy by Mechanical Milling at Low Li Concentration and Its Reaction with Water for Hydrogen Generation
Research on hydrogen production by chemical methods has focused on combining metals to carry out the hydrolysis reaction under ambient conditions. In particular, aluminum and lithium metals were considered, with lithium used at low concentrations in order to activate aluminum. Under these conditions, the metals can react with water to obtain the maximum hydrogen yield. The main objective of this work was to prepare the lithium−aluminum alloy by mechanical milling and its chemical reaction with water to produce hydrogen under laboratory conditions. A high–energy Spex mill was used for material preparation and the time scheduled for alloys preparation was relatively short. Several techniques were used for its characterization, such as X–ray diffraction, scanning electron microscopy, gas chromatography, and low-temperature physical adsorption. According to the results, two phases were produced during the milling process when using 5% lithium. The volume of hydrogen generated was measured using a graduated burette. Depending on the volume obtained, the aluminum reacted to generate hydrogen with an efficiency of 95.24%. No additives or catalysts were used in material synthesis or hydrogen production. According to these results, the hydrogen does not require any purification because it is clean hydrogen and can therefore be used directly in fuel cells.
Open AccessPreparation of AlLi Alloy by Mechanical Milling at Low Li Concentration and Its Reaction with Water for Hydrogen Generation
Research on hydrogen production by chemical methods has focused on combining metals to carry out the hydrolysis reaction under ambient conditions. In particular, aluminum and lithium metals were considered, with lithium used at low concentrations in order to activate aluminum. Under these conditions, the metals can react with water to obtain the maximum hydrogen yield. The main objective of this work was to prepare the lithium−aluminum alloy by mechanical milling and its chemical reaction with water to produce hydrogen under laboratory conditions. A high–energy Spex mill was used for material preparation and the time scheduled for alloys preparation was relatively short. Several techniques were used for its characterization, such as X–ray diffraction, scanning electron microscopy, gas chromatography, and low-temperature physical adsorption. According to the results, two phases were produced during the milling process when using 5% lithium. The volume of hydrogen generated was measured using a graduated burette. Depending on the volume obtained, the aluminum reacted to generate hydrogen with an efficiency of 95.24%. No additives or catalysts were used in material synthesis or hydrogen production. According to these results, the hydrogen does not require any purification because it is clean hydrogen and can therefore be used directly in fuel cells.
- Open Access
High Efficiency in Clean Hydrogen Production Using Water and AlLi Phases Prepared by Mechanical Alloying
In this work, the results of clean hydrogen production from the direct chemical reaction between aluminum–lithium compounds and distilled water under normal conditions, without additives or catalysts, are presented. The material was prepared by mechanical alloying using a high-energy Spex-type mill in an Al20Li ratio. Relatively short milling times were programmed for the preparation of AlLi phases. Through this process, two phases (AlLi and Al8.9Li1.1) were identified, which react efficiently to produce clean hydrogen. The experiments demonstrate fast and self-sustained reactions between AlLi phases and distilled water. In both the phase preparation and hydrogen generation, 100% efficiency was achieved. The hydrolysis reaction occurred quickly, and the hydrogen volume generated was 1700 mL/g of material. Under these conditions, aluminum generates 1390 mL of hydrogen, and lithium generates 310 mL/g from both AlLi phases. A single by-product (LiAl2(OH)7·2H2O) was identified. According to the results and the conditions applied in this research, the hydrogen produced does not require prior purification and can therefore be used directly in fuel cells. The AlLi–water reaction is a promising process for generating hydrogen in a simple and relatively short time compared to other hydrogen production methods. In this process, no greenhouse gas emissions were produced.
Open AccessHigh Efficiency in Clean Hydrogen Production Using Water and AlLi Phases Prepared by Mechanical Alloying
In this work, the results of clean hydrogen production from the direct chemical reaction between aluminum–lithium compounds and distilled water under normal conditions, without additives or catalysts, are presented. The material was prepared by mechanical alloying using a high-energy Spex-type mill in an Al20Li ratio. Relatively short milling times were programmed for the preparation of AlLi phases. Through this process, two phases (AlLi and Al8.9Li1.1) were identified, which react efficiently to produce clean hydrogen. The experiments demonstrate fast and self-sustained reactions between AlLi phases and distilled water. In both the phase preparation and hydrogen generation, 100% efficiency was achieved. The hydrolysis reaction occurred quickly, and the hydrogen volume generated was 1700 mL/g of material. Under these conditions, aluminum generates 1390 mL of hydrogen, and lithium generates 310 mL/g from both AlLi phases. A single by-product (LiAl2(OH)7·2H2O) was identified. According to the results and the conditions applied in this research, the hydrogen produced does not require prior purification and can therefore be used directly in fuel cells. The AlLi–water reaction is a promising process for generating hydrogen in a simple and relatively short time compared to other hydrogen production methods. In this process, no greenhouse gas emissions were produced.
- Open Access
- 10 January 2016
- Published by Sciencedomain International in British Journal of Applied Science & Technology
- Vol. 15 (2) , 1-9
Oxygen and Hydrogen Reaction “In situ” with Magnesium and Tantalum in a Mechanical Milling System When a Solvent is Used
The purpose of this paper is study the preparation “in situ” of magnesium–tantalum phases when reacted with oxygen and hydrogen during a mechanical milling process. Different phases were formed as function of the milling time. High energy ball milling was utilized to prepare hydrogenated compounds by controling the milling between 5 and 20 hours with a ball powder weight ratio of 10 and using methanol as the control agent. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to characterize the compounds. The XRD results at 20 h of milling revealed that only hydrogenated species (Ta2H and TaH0.5) and Mg(OH)2 were present.
- 10 January 2016
- Published by Sciencedomain International in British Journal of Applied Science & Technology
- Vol. 15 (2) , 1-9
Open AccessOxygen and Hydrogen Reaction “In situ” with Magnesium and Tantalum in a Mechanical Milling System When a Solvent is Used
The purpose of this paper is study the preparation “in situ” of magnesium–tantalum phases when reacted with oxygen and hydrogen during a mechanical milling process. Different phases were formed as function of the milling time. High energy ball milling was utilized to prepare hydrogenated compounds by controling the milling between 5 and 20 hours with a ball powder weight ratio of 10 and using methanol as the control agent. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to characterize the compounds. The XRD results at 20 h of milling revealed that only hydrogenated species (Ta2H and TaH0.5) and Mg(OH)2 were present.
- 16 October 2009
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 35 (21) , 12120-12124
MgAl alloy synthesis, characterization and its use in hydrogen storage
- 16 October 2009
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 35 (21) , 12120-12124
MgAl alloy synthesis, characterization and its use in hydrogen storage