Fu Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fu Guo has a total of 165 co-authors. Here are the top co-authors by number of shared publications:
Yishu Wang
34 shared publications- Limin Ma
Faculty of Materials and Manufacturing, Beijing University of Technology, Beijing, China
23 shared publications Limin Ma
16 shared publicationsXiaoliang Ji
13 shared publicationsJing Han
Faculty of Materials and Manufacturing, Beijing University of Technology, Beijing 100124, P. R. China
11 shared publicationsGuangchen Xu
Beijing University of Technology
9 shared publications
Latest Publications
- 6 November 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
Direct-Ink-Writing Printed Aerogels with Infiltrated Field’s Metal for High Thermal Conductivity and Shape Stability
The increasing power density of electronic devices demands thermal interface materials with efficient heat dissipation and structural stability. Phase-change thermal interface materials (PCTIMs) provide thermal buffering but are limited by low thermal conductivity and leakage during phase transitions. Here, a direct-ink-writing (DIW) strategy using a biobased multilayer graphene (MLG)/chitosan quaternary ammonium salt (CQAS)/cationic cellulose nanofiber (CCNF) composite ink (GQC) constructs vertically aligned porous aerogels. The GQC aerogels feature controllable 200–400 μm macroscopic channels, a vertically aligned internal porous architecture, and good mechanical compliance with a Young’s modulus of 0.322 ± 0.008 MPa. Pressure-assisted infiltration of Field’s metal (FM, 62.3 °C) forms a bicontinuous GQC/FM thermal network, in which continuous FM provides efficient heat-transfer pathways while the porous GQC framework confines molten metal. At 29 vol % FM, the composite achieves a through-plane thermal conductivity of 8.57 W m–1 K–1 and retains 95.0% of its initial value after 200 thermal cycles. Moreover, a simple alkali-assisted process recovers 92% of FM for reuse, yielding a regenerated composite with a thermal conductivity of 7.81 W m–1 K–1 (91.1% of the original value). This work presents a metallic PCTIM design integrating efficient heat transport, shape stability, and recyclability for sustainable thermal management.
- 6 November 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
Direct-Ink-Writing Printed Aerogels with Infiltrated Field’s Metal for High Thermal Conductivity and Shape Stability
The increasing power density of electronic devices demands thermal interface materials with efficient heat dissipation and structural stability. Phase-change thermal interface materials (PCTIMs) provide thermal buffering but are limited by low thermal conductivity and leakage during phase transitions. Here, a direct-ink-writing (DIW) strategy using a biobased multilayer graphene (MLG)/chitosan quaternary ammonium salt (CQAS)/cationic cellulose nanofiber (CCNF) composite ink (GQC) constructs vertically aligned porous aerogels. The GQC aerogels feature controllable 200–400 μm macroscopic channels, a vertically aligned internal porous architecture, and good mechanical compliance with a Young’s modulus of 0.322 ± 0.008 MPa. Pressure-assisted infiltration of Field’s metal (FM, 62.3 °C) forms a bicontinuous GQC/FM thermal network, in which continuous FM provides efficient heat-transfer pathways while the porous GQC framework confines molten metal. At 29 vol % FM, the composite achieves a through-plane thermal conductivity of 8.57 W m–1 K–1 and retains 95.0% of its initial value after 200 thermal cycles. Moreover, a simple alkali-assisted process recovers 92% of FM for reuse, yielding a regenerated composite with a thermal conductivity of 7.81 W m–1 K–1 (91.1% of the original value). This work presents a metallic PCTIM design integrating efficient heat transport, shape stability, and recyclability for sustainable thermal management.
- 2 November 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1085
Dual-functional nickel-coated carbon fiber reinforced SnBiIn composites via magnetic alignment
- 2 November 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1085
Dual-functional nickel-coated carbon fiber reinforced SnBiIn composites via magnetic alignment
- 4 September 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (11) , 9311-9318
Enhancing SAC305 Solder Joints with Ni-Coated Carbon Fibers
- 4 September 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (11) , 9311-9318
Enhancing SAC305 Solder Joints with Ni-Coated Carbon Fibers
- 3 August 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (15) , 12853-12868
Homologous Bisphenol-A Modification Enables SiO2/Epoxy Composites with Ultralow Thermal Expansion, High T g, and Superior Thermal Shock Resistance for Power Device Packaging
Next-generation power device packaging demands epoxy (EP) composites that achieve a critical combination of low thermal expansion, high-temperature resistance, and thermal shock stability. High-performance EP composites were developed using a synergistic materials design strategy combining filler surface modification, filler gradation, and resin blending. Silica (SiO2) was surface-modified with 2,2-bis(4-hydroxyphenyl) propane (Br5215), a bisphenol-A-based molecule structurally compatible with the epoxy matrix, forming a robust interfacial layer via covalent bonding and π–π interactions. This effectively suppresses filler agglomeration and enhances interfacial adhesion. In parallel, blending difunctional and trifunctional epoxy resins enabled simultaneous control of viscosity and cross-link density. Experimental results show that the glass transition temperature (Tg) of the B-SiO2/EP composite reaches 205.6 °C. The coefficient of thermal expansion below Tg, denoted as α1, is 25.81 × 10–6/°C, representing a reduction of 70.1% compared to neat EP. After 1000 thermal shock cycles (−60 to 150 °C), the composite still maintains a Tg of 202.4 °C (only a 1.6% decrease) and an α1 of 26.6 × 10–6/°C (only a 3.2% increase), with no interfacial delamination from the copper substrate. This represents a significant improvement over neat EP (delamination after 200 cycles) and SiO2/EP (delamination after 800 cycles). This study provides a practical strategy for developing high-reliability epoxy encapsulants for power device packaging.
- 3 August 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (15) , 12853-12868
Homologous Bisphenol-A Modification Enables SiO2/Epoxy Composites with Ultralow Thermal Expansion, High T g, and Superior Thermal Shock Resistance for Power Device Packaging
Next-generation power device packaging demands epoxy (EP) composites that achieve a critical combination of low thermal expansion, high-temperature resistance, and thermal shock stability. High-performance EP composites were developed using a synergistic materials design strategy combining filler surface modification, filler gradation, and resin blending. Silica (SiO2) was surface-modified with 2,2-bis(4-hydroxyphenyl) propane (Br5215), a bisphenol-A-based molecule structurally compatible with the epoxy matrix, forming a robust interfacial layer via covalent bonding and π–π interactions. This effectively suppresses filler agglomeration and enhances interfacial adhesion. In parallel, blending difunctional and trifunctional epoxy resins enabled simultaneous control of viscosity and cross-link density. Experimental results show that the glass transition temperature (Tg) of the B-SiO2/EP composite reaches 205.6 °C. The coefficient of thermal expansion below Tg, denoted as α1, is 25.81 × 10–6/°C, representing a reduction of 70.1% compared to neat EP. After 1000 thermal shock cycles (−60 to 150 °C), the composite still maintains a Tg of 202.4 °C (only a 1.6% decrease) and an α1 of 26.6 × 10–6/°C (only a 3.2% increase), with no interfacial delamination from the copper substrate. This represents a significant improvement over neat EP (delamination after 200 cycles) and SiO2/EP (delamination after 800 cycles). This study provides a practical strategy for developing high-reliability epoxy encapsulants for power device packaging.
- 7 June 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (9) , 8083-8098
High-Reliability Cu-Cu3Sn Composite Bonding for Power Electronics in Harsh Environments
- 7 June 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (9) , 8083-8098
High-Reliability Cu-Cu3Sn Composite Bonding for Power Electronics in Harsh Environments
- Open Access
- 6 June 2026
- Published by Elsevier in SSRN Electronic Journal
Thermodynamic and Kinetic Competition Governing β-Sn Twin Formation in SAC305-xIn Solder Balls under Different Cooling Rates
The pronounced anisotropy of β-Sn critically compromises the reliability of microelectronic solder joints, particularly under electromigration and thermomechanical fatigue conditions. Increasing twin density in Sn-based solders has been identified as an effective strategy for mitigating reliability issues associated with β-Sn anisotropy. To achieve controllable twin formation, this paper investigated the effects of Indium (In) content (0, 2, 5, 10, 13 wt.%) and cooling rates (102-104 K/s) on microstructural evolution and twin formation behavior in SAC305-xIn solder balls. Under the air-cooling condition (~10² K/s), twin density increased monotonically with In content, which was attributed to the reduction in stacking fault energy of the β-Sn matrix—confirmed by first-principles calculations based on density functional theory. Furthermore, In modified the solidification undercooling behavior of the SAC305 alloy system and therefore promoted an undercooling regime favorable for anisotropic preferential growth and cyclic twinning of β-Sn. Under the water-cooling (~103K/s) and liquid-nitrogen-cooling condition (~104K/s), however, the positive effect of In on twin formation was markedly weakened. The excessive undercooling generated under ultra-high cooling rates dramatically elevated the nucleation rate of β-Sn, triggering extensive stochastic nucleation that suppressed the preferential growth required for twin formation. Consequently, the microstructure transformed from a twin-dominated morphology to a randomly oriented, multiple-grain structure with a substantially reduced twin fraction. This work elucidates the interplay between thermodynamic driving forces and rapid-solidification kinetics in governing β-Sn twin formation and offers theoretical guidance for introducing twin structures to enhance the reliability of Sn-based solder joints.
- 6 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermodynamic and Kinetic Competition Governing β-Sn Twin Formation in SAC305-xIn Solder Balls under Different Cooling Rates
The pronounced anisotropy of β-Sn critically compromises the reliability of microelectronic solder joints, particularly under electromigration and thermomechanical fatigue conditions. Increasing twin density in Sn-based solders has been identified as an effective strategy for mitigating reliability issues associated with β-Sn anisotropy. To achieve controllable twin formation, this paper investigated the effects of Indium (In) content (0, 2, 5, 10, 13 wt.%) and cooling rates (102-104 K/s) on microstructural evolution and twin formation behavior in SAC305-xIn solder balls. Under the air-cooling condition (~10² K/s), twin density increased monotonically with In content, which was attributed to the reduction in stacking fault energy of the β-Sn matrix—confirmed by first-principles calculations based on density functional theory. Furthermore, In modified the solidification undercooling behavior of the SAC305 alloy system and therefore promoted an undercooling regime favorable for anisotropic preferential growth and cyclic twinning of β-Sn. Under the water-cooling (~103K/s) and liquid-nitrogen-cooling condition (~104K/s), however, the positive effect of In on twin formation was markedly weakened. The excessive undercooling generated under ultra-high cooling rates dramatically elevated the nucleation rate of β-Sn, triggering extensive stochastic nucleation that suppressed the preferential growth required for twin formation. Consequently, the microstructure transformed from a twin-dominated morphology to a randomly oriented, multiple-grain structure with a substantially reduced twin fraction. This work elucidates the interplay between thermodynamic driving forces and rapid-solidification kinetics in governing β-Sn twin formation and offers theoretical guidance for introducing twin structures to enhance the reliability of Sn-based solder joints.
- Open Access
- 2 June 2026
- Published by Elsevier in SSRN Electronic Journal
Thermodynamic and Kinetic Competition Governing β-Sn Twin Formation in SAC305- x In Solder Balls under Different Cooling Rates
The pronounced anisotropy of β-Sn critically compromises the reliability of microelectronic solder joints, particularly under electromigration and thermomechanical fatigue conditions. Increasing twin density in Sn-based solders has been identified as an effective strategy for mitigating reliability issues associated with β-Sn anisotropy. To achieve controllable twin formation, this paper investigated the effects of Indium (In) content (0, 2, 5, 10, 13 wt.%) and cooling rates (102-104 K/s) on microstructural evolution and twin formation behavior in SAC305-xIn solder balls. Under the air-cooling condition (~10² K/s), twin density increased monotonically with In content, which was attributed to the reduction in stacking fault energy of the β-Sn matrix—confirmed by first-principles calculations based on density functional theory. Furthermore, In modified the solidification undercooling behavior of the SAC305 alloy system and therefore promoted an undercooling regime favorable for anisotropic preferential growth and cyclic twinning of β-Sn. Under the water-cooling (~103K/s) and liquid-nitrogen-cooling condition (~104K/s), however, the positive effect of In on twin formation was markedly weakened. The excessive undercooling generated under ultra-high cooling rates dramatically elevated the nucleation rate of β-Sn, triggering extensive stochastic nucleation that suppressed the preferential growth required for twin formation. Consequently, the microstructure transformed from a twin-dominated morphology to a randomly oriented, multiple-grain structure with a substantially reduced twin fraction. This work elucidates the interplay between thermodynamic driving forces and rapid-solidification kinetics in governing β-Sn twin formation and offers theoretical guidance for introducing twin structures to enhance the reliability of Sn-based solder joints.
- 2 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermodynamic and Kinetic Competition Governing β-Sn Twin Formation in SAC305- x In Solder Balls under Different Cooling Rates
The pronounced anisotropy of β-Sn critically compromises the reliability of microelectronic solder joints, particularly under electromigration and thermomechanical fatigue conditions. Increasing twin density in Sn-based solders has been identified as an effective strategy for mitigating reliability issues associated with β-Sn anisotropy. To achieve controllable twin formation, this paper investigated the effects of Indium (In) content (0, 2, 5, 10, 13 wt.%) and cooling rates (102-104 K/s) on microstructural evolution and twin formation behavior in SAC305-xIn solder balls. Under the air-cooling condition (~10² K/s), twin density increased monotonically with In content, which was attributed to the reduction in stacking fault energy of the β-Sn matrix—confirmed by first-principles calculations based on density functional theory. Furthermore, In modified the solidification undercooling behavior of the SAC305 alloy system and therefore promoted an undercooling regime favorable for anisotropic preferential growth and cyclic twinning of β-Sn. Under the water-cooling (~103K/s) and liquid-nitrogen-cooling condition (~104K/s), however, the positive effect of In on twin formation was markedly weakened. The excessive undercooling generated under ultra-high cooling rates dramatically elevated the nucleation rate of β-Sn, triggering extensive stochastic nucleation that suppressed the preferential growth required for twin formation. Consequently, the microstructure transformed from a twin-dominated morphology to a randomly oriented, multiple-grain structure with a substantially reduced twin fraction. This work elucidates the interplay between thermodynamic driving forces and rapid-solidification kinetics in governing β-Sn twin formation and offers theoretical guidance for introducing twin structures to enhance the reliability of Sn-based solder joints.
- 13 April 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 340
Creep behavior and microstructural evolution of Ni@CF composite solder joints under shear loading
- 13 April 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 340
Creep behavior and microstructural evolution of Ni@CF composite solder joints under shear loading
- 21 January 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (10) , 6552-6580
Research progress on the application of phase change materials in thermal management for electronic packaging
- 21 January 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (10) , 6552-6580
Research progress on the application of phase change materials in thermal management for electronic packaging