Mohd Sayuti Ab Karim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohd Sayuti Ab Karim has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Aly Diaa Sarhan
Department of Mechanical Engineering, King Fahd University of Petroleum and Minerals, Dhahran, Saudi Arabia
4 shared publications M. Hamdi
Centre of Advanced Manufacturing and Material Processing, Department of Design and Manufacturing, Engineering Faculty, University of Malaya, Kuala Lumpur, Malaysia
2 shared publications- Hamdi Shukor
Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur, Malaysia
1 shared publication M. Fadzil
Centre of Advanced Manufacturing and Material Processing, Department of Engineering Design and Manufacture, University of Malaya, Kuala Lumpur, Malaysia
1 shared publicationMohd Hamdi Abd Shukor
Centre of Advanced Manufacturing and Material Processing, Department of Engineering Design and Manufacture , University of Malaya , Kuala Lumpur, Malaysia
1 shared publication
Latest Publications
- 9 October 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 67 (1-4) , 833-849
An investigation of optimum SiO2 nanolubrication parameters in end milling of aerospace Al6061-T6 alloy
- 9 October 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 67 (1-4) , 833-849
An investigation of optimum SiO2 nanolubrication parameters in end milling of aerospace Al6061-T6 alloy
- 3 February 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 63 (5-8) , 505-512
Reduction of power and lubricant oil consumption in milling process using a new SiO2 nanolubrication system
- 3 February 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 63 (5-8) , 505-512
Reduction of power and lubricant oil consumption in milling process using a new SiO2 nanolubrication system
- 2 October 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 60 (9-12) , 939-950
Enhancement and verification of a machined surface quality for glass milling operation using CBN grinding tool—Taguchi approach
- 2 October 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 60 (9-12) , 939-950
Enhancement and verification of a machined surface quality for glass milling operation using CBN grinding tool—Taguchi approach
- 26 May 2011
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 26 (8) , 969-976
Experimental Study on Minimizing Edge Chipping in Glass Milling Operation Using an Internal CBN Grinding Tool
Glass is one of the most difficult materials to be machined due to its brittle nature and unique structure as frequent occurrence of fracture and edge chipping during machining has to be avoided. To minimize edge chipping of the machined glass, which is common when cutting materials harder than 50 HRC, adopting right parameters is required followed by additional effort and cost. This article presents experimentation in minimizing the edge chipping for glass milling operations using an internal cubic boron nitride grinding tool by optimizing the machining parameters. Taguchi optimization method is the most effective method to optimize the machining parameters, in which the most significant response variables affecting edge chipping could be identified. In glass milling operation, several machining parameters are considered to be significant in affecting edge chipping. These parameters include lubrication pressure and direction, feed rate, spindle speed, and depth of cut. The standard orthogonal array of L 16 (44) is used, while the signal-to-noise response analysis and analysis of variance methods are carried out to determine which parameters are statistically significant. Finally, confirmation tests are carried out to investigate the optimization improvements.
- 26 May 2011
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 26 (8) , 969-976
Experimental Study on Minimizing Edge Chipping in Glass Milling Operation Using an Internal CBN Grinding Tool
Glass is one of the most difficult materials to be machined due to its brittle nature and unique structure as frequent occurrence of fracture and edge chipping during machining has to be avoided. To minimize edge chipping of the machined glass, which is common when cutting materials harder than 50 HRC, adopting right parameters is required followed by additional effort and cost. This article presents experimentation in minimizing the edge chipping for glass milling operations using an internal cubic boron nitride grinding tool by optimizing the machining parameters. Taguchi optimization method is the most effective method to optimize the machining parameters, in which the most significant response variables affecting edge chipping could be identified. In glass milling operation, several machining parameters are considered to be significant in affecting edge chipping. These parameters include lubrication pressure and direction, feed rate, spindle speed, and depth of cut. The standard orthogonal array of L 16 (44) is used, while the signal-to-noise response analysis and analysis of variance methods are carried out to determine which parameters are statistically significant. Finally, confirmation tests are carried out to investigate the optimization improvements.