Mahmood Yahyai
Mahmood Yahyai has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Bahram Rezayibana
KNT University of Technology
3 shared publications- Mehdi Shokouhian
Department of Civil and Environmental Engineering, Center for the Built Environment and Infrastructure Studies (CBEIS), Morgan State University, Baltimore, MD 21251, USA
2 shared publications - Monique Head
Univ. of Delaware
2 shared publications - Abbas Rezaeian
Department of Civil Engineering, Faculty of Civil Engineering and Architecture, Shahid Chamran University of Ahvaz, Ahvaz, Iran
1 shared publication Amir Saedi Daryan
Department of Civil Engineering, K. N. Toosi University of Technology, Tehran, Iran
1 shared publication- Amir Saedi Daryan
Faculty of Civil, Water and Environmental Engineering Shahid Beheshti University Tehran Iran
1 shared publication
Latest Publications
- 7 January 2020
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 44 (S1) , 205-215
Toward Optimizing Dynamic Characteristics of Non-conventional TMDs in Multi-degree-of-Freedom Systems
- 7 January 2020
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 44 (S1) , 205-215
Toward Optimizing Dynamic Characteristics of Non-conventional TMDs in Multi-degree-of-Freedom Systems
- 24 June 2019
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 25 (10) , 1-20
Optimum Parameters for Large Mass Ratio TMDs Using Frequency Response Function
The paper proposes a new approach for optimal design structures equipped with tuned mass dampers (TMDs) with large mass ratios. The approach is based on minimizing the frequency response function (FRF) of displacement response of the structure as well as the acceleration of the TMD that leads to almost equal modal damping ratios in the first and second mode of vibration. Furthermore, two regression equations are proposed to predict the optimum TMD properties. It is concluded that choosing the optimum TMD parameters as suggested in this study provides up to 94% reduction in the maximum FRF of structural displacement.
- 24 June 2019
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 25 (10) , 1-20
Optimum Parameters for Large Mass Ratio TMDs Using Frequency Response Function
The paper proposes a new approach for optimal design structures equipped with tuned mass dampers (TMDs) with large mass ratios. The approach is based on minimizing the frequency response function (FRF) of displacement response of the structure as well as the acceleration of the TMD that leads to almost equal modal damping ratios in the first and second mode of vibration. Furthermore, two regression equations are proposed to predict the optimum TMD properties. It is concluded that choosing the optimum TMD parameters as suggested in this study provides up to 94% reduction in the maximum FRF of structural displacement.
- 1 October 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30 (10)
Residual Mechanical Properties of High-Strength Steel Bolts after Exposure to Elevated Temperature
This paper presents results from experimental studies on residual mechanical properties of Grade 10.9 bolts exposed to elevated temperatures. The effects of various target temperatures on the residual mechanical properties, including ultimate and yield strengths, stress-strain response, and the failure modes of bolts, were investigated. Furthermore, the influence of temperature level, chemical composition of feedstock steels, and heat treatment parameters in the fabrication process of Grade 10.9 bolts on residual mechanical properties was studied. Data from the experiments indicate quick reduction in residual strength of the bolts when heated up to temperatures greater than 400°C, reaching to 50% of its ultimate strength when exposure temperature reaches 800°C. Tempering the temperature in the bolt manufacturing process and carbon content in steel are two other important factors besides exposure temperature that have a great influence on residual properties of Grade 10.9 bolts. Based on the experimental results, a set of predictive equations is also proposed for assessing the temperature-dependent residual mechanical properties in Grade 10.9 bolts.
- 1 October 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30 (10)
Residual Mechanical Properties of High-Strength Steel Bolts after Exposure to Elevated Temperature
This paper presents results from experimental studies on residual mechanical properties of Grade 10.9 bolts exposed to elevated temperatures. The effects of various target temperatures on the residual mechanical properties, including ultimate and yield strengths, stress-strain response, and the failure modes of bolts, were investigated. Furthermore, the influence of temperature level, chemical composition of feedstock steels, and heat treatment parameters in the fabrication process of Grade 10.9 bolts on residual mechanical properties was studied. Data from the experiments indicate quick reduction in residual strength of the bolts when heated up to temperatures greater than 400°C, reaching to 50% of its ultimate strength when exposure temperature reaches 800°C. Tempering the temperature in the bolt manufacturing process and carbon content in steel are two other important factors besides exposure temperature that have a great influence on residual properties of Grade 10.9 bolts. Based on the experimental results, a set of predictive equations is also proposed for assessing the temperature-dependent residual mechanical properties in Grade 10.9 bolts.
- 30 September 2015
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 15 (3) , 541-555
A simplified methodology to determine damping for special concentrically-braced frames
- 30 September 2015
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 15 (3) , 541-555
A simplified methodology to determine damping for special concentrically-braced frames
- 22 March 2015
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 13 (10) , 2945-2971
Direct displacement-based design of special concentrically-braced frames in near-fault regions
- 22 March 2015
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 13 (10) , 2945-2971
Direct displacement-based design of special concentrically-braced frames in near-fault regions
- 1 March 2014
- Published by SAGE Publications in International Journal of Space Structures
- Vol. 29 (1) , 39-48
Seismic Behavior of Single Layer Schwedler Domes
Space structures can efficiently resist seismic loads due to their lightweight, geometry, high residual strength and high redundancy. Determination of seismic response factor of space structures is essential for based on equivalent static method. Seismic behavior of single layer Schwedler domes is studied in this paper. Six domes with different spans and same number of nodes and elements as well as loading conditions are modeled using finite element method. Nonlinear static and dynamic analyses are carried out to study the seismic behavior of these domes. The force-displacement diagrams are used to obtain a formula for predicting the fundamental natural period. Using the proposed equation, response modification factor, Rw, is determined from these analyses. Moreover, ductility curves are compared at different levels of the dome. Finally, a formula is proposed for calculation of natural period of vibration and response modification factor of Schwedler domes.
- 1 March 2014
- Published by SAGE Publications in International Journal of Space Structures
- Vol. 29 (1) , 39-48
Seismic Behavior of Single Layer Schwedler Domes
Space structures can efficiently resist seismic loads due to their lightweight, geometry, high residual strength and high redundancy. Determination of seismic response factor of space structures is essential for based on equivalent static method. Seismic behavior of single layer Schwedler domes is studied in this paper. Six domes with different spans and same number of nodes and elements as well as loading conditions are modeled using finite element method. Nonlinear static and dynamic analyses are carried out to study the seismic behavior of these domes. The force-displacement diagrams are used to obtain a formula for predicting the fundamental natural period. Using the proposed equation, response modification factor, Rw, is determined from these analyses. Moreover, ductility curves are compared at different levels of the dome. Finally, a formula is proposed for calculation of natural period of vibration and response modification factor of Schwedler domes.
- 14 June 2011
- Published by Springer Nature in Earthquake Engineering and Engineering Vibration
- Vol. 10 (2) , 211-218
Effect of near-fault earthquakes with forward directivity on telecommunication towers
- 14 June 2011
- Published by Springer Nature in Earthquake Engineering and Engineering Vibration
- Vol. 10 (2) , 211-218
Effect of near-fault earthquakes with forward directivity on telecommunication towers
- 2 March 2011
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 20 (2) , 177-189
Wind effect on milad tower using computational fluid dynamics
Milad tower is located in Tehran, Iran, and is a 436‐m telecommunication tower ranked as the fourth tallest structure in the world. Because of its specific use and also because of highly sensitive communication devices installed on the tower, nonlinear deformations under future severe winds and earthquakes should be studied. In this paper, a comprehensive study is carried out to investigate the effect of wind on this tower. The techniques of computational fluid dynamics, such as large eddy simulation (LES), Reynolds Averaged Navier–Stokes Equations (RANS) model and so on, were adopted in this study to predict wind loads on and wind flows around the building. The calculated results are compared with those of wind tunnel test. It was found through the comparison that the LES with a dynamic subgrid‐scale model can give satisfactory predictions for mean and dynamic wind loads on the specific structure of Milad tower, while the RANS model with modifications can yield encouraging results in most cases and has the advantage of providing rapid solutions. Furthermore, it was observed that typical features of the flow fields around such a surface‐mounted bluff body standing in atmospheric boundary layers can be captured numerically. Copyright © 2009 John Wiley & Sons, Ltd.
- 2 March 2011
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 20 (2) , 177-189
Wind effect on milad tower using computational fluid dynamics
Milad tower is located in Tehran, Iran, and is a 436‐m telecommunication tower ranked as the fourth tallest structure in the world. Because of its specific use and also because of highly sensitive communication devices installed on the tower, nonlinear deformations under future severe winds and earthquakes should be studied. In this paper, a comprehensive study is carried out to investigate the effect of wind on this tower. The techniques of computational fluid dynamics, such as large eddy simulation (LES), Reynolds Averaged Navier–Stokes Equations (RANS) model and so on, were adopted in this study to predict wind loads on and wind flows around the building. The calculated results are compared with those of wind tunnel test. It was found through the comparison that the LES with a dynamic subgrid‐scale model can give satisfactory predictions for mean and dynamic wind loads on the specific structure of Milad tower, while the RANS model with modifications can yield encouraging results in most cases and has the advantage of providing rapid solutions. Furthermore, it was observed that typical features of the flow fields around such a surface‐mounted bluff body standing in atmospheric boundary layers can be captured numerically. Copyright © 2009 John Wiley & Sons, Ltd.
- 3 November 2008
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 18 (8) , 877-890
Nonlinear seismic response of Milad Tower using finite element model
Milad Tower is a 436‐m‐tall telecommunications tower ranked as the fourth tallest structure of its kind in the world. The study of its seismic behaviour is of great importance as it is located in a highly seismic‐prone region. Because of the existence of the world's largest revolving restaurant in the head structure, and also because of the highly sensitive communication devices such as TV and telecommunications antennas installed on the tower, nonlinear deformation under future earthquakes should be studied. In this paper, a detailed finite element model is developed and nonlinear dynamic analysis was carried out under the design earthquakes. The foundation, concrete shaft, head structure and 120‐m antenna structure were modelled. Three components of the earthquakes are considered, and the selected earthquakes were normalized based on three design levels: design basis level, maximum design level and maximum credible level. The results of the analysis showed that all parts of the tower behave in the plastic zone except the elements of the head structure. It is also observed that in some cases, the earthquakes with lower peak accelerations and higher energy contents may have more severe effect on the tower than that with higher peak accelerations. Copyright © 2008 John Wiley & Sons, Ltd.
- 3 November 2008
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 18 (8) , 877-890
Nonlinear seismic response of Milad Tower using finite element model
Milad Tower is a 436‐m‐tall telecommunications tower ranked as the fourth tallest structure of its kind in the world. The study of its seismic behaviour is of great importance as it is located in a highly seismic‐prone region. Because of the existence of the world's largest revolving restaurant in the head structure, and also because of the highly sensitive communication devices such as TV and telecommunications antennas installed on the tower, nonlinear deformation under future earthquakes should be studied. In this paper, a detailed finite element model is developed and nonlinear dynamic analysis was carried out under the design earthquakes. The foundation, concrete shaft, head structure and 120‐m antenna structure were modelled. Three components of the earthquakes are considered, and the selected earthquakes were normalized based on three design levels: design basis level, maximum design level and maximum credible level. The results of the analysis showed that all parts of the tower behave in the plastic zone except the elements of the head structure. It is also observed that in some cases, the earthquakes with lower peak accelerations and higher energy contents may have more severe effect on the tower than that with higher peak accelerations. Copyright © 2008 John Wiley & Sons, Ltd.