Dong Hyun Bae
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dong Hyun Bae has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Jaehyuck Shin
Department of Materials Science and Engineering, Yonsei University, Seoul, Korea
5 shared publicationsH.J. Choi
School of Advanced Materials Engineering, Kookmin University, Seoul 136-702, Republic of Korea
4 shared publications- Se-Eun Shin
Department of Advanced Materials Engineering, Sunchon National University, Suncheon, Republic of Korea
4 shared publications H. Kang
Korea Institute of Industrial Technology, Siheung, Republic of Korea
3 shared publicationsHyunjoo Choi
Department of Materials Science and Engineering, Yonsei University, Seoul, Korea
3 shared publications- Sangjun Lee
Department of Materials Science and Engineering, Yonsei University, Seoul 03722, Republic of Korea
3 shared publications
Latest Publications
- 29 April 2026
- Published by Springer Nature in Metals and Materials International
- Vol. 32 (10) , 1-18
Computational Analysis on the Composition-Dependent Solute Clustering Behavior During Early-Stage Natural Aging in Al–Si–Mg–(Cu) Alloys
- 29 April 2026
- Published by Springer Nature in Metals and Materials International
- Vol. 32 (10) , 1-18
Computational Analysis on the Composition-Dependent Solute Clustering Behavior During Early-Stage Natural Aging in Al–Si–Mg–(Cu) Alloys
- Open Access
Natural and Artificial Aging Effects on the Deformation Behaviors of Al–Mg–Zn Alloy Sheets
This study investigated the effects of aging profiles on the precipitate formation and the corresponding strengthening and deformation behaviors of Al–Mg–Zn alloys. The alloys subjected to natural aging (NA) demonstrated significantly enhanced ductility at equivalent stress levels compared to those subjected to artificial aging (AA). In AA-treated alloys, η′ and η-phases with incoherent interfaces were formed, while GP zones and solute clusters were dominantly exhibited in the NA-treated alloy with a coherent interface with the matrix. Due to the change in interface bonding, the dislocation movement and pinning behavior after deformation are varied depending on the aging conditions of Al–Mg–Zn alloy sheet. Thus, the elongation to fracture of the NA alloy sheet was improved compared to that of the AA alloy sheet because of the enhanced work-hardening capacity and the thin precipitate-free zone (PFZ). Deformation textures and dislocation densities varied between NA and AA treatments, as revealed by electron backscatter diffraction (EBSD) and kernel average misorientation (KAM) analysis. The interactions between the precipitates, dislocations, and the PFZ in the AA- and NA-treated alloys were analyzed via transmission electron microscopy (TEM). The insights gained from this research provide a valuable foundation for industrial applications, particularly in sectors demanding lightweight, high-strength materials, where optimizing the aging process can lead to significant performance improvement and cost savings.
Open AccessNatural and Artificial Aging Effects on the Deformation Behaviors of Al–Mg–Zn Alloy Sheets
This study investigated the effects of aging profiles on the precipitate formation and the corresponding strengthening and deformation behaviors of Al–Mg–Zn alloys. The alloys subjected to natural aging (NA) demonstrated significantly enhanced ductility at equivalent stress levels compared to those subjected to artificial aging (AA). In AA-treated alloys, η′ and η-phases with incoherent interfaces were formed, while GP zones and solute clusters were dominantly exhibited in the NA-treated alloy with a coherent interface with the matrix. Due to the change in interface bonding, the dislocation movement and pinning behavior after deformation are varied depending on the aging conditions of Al–Mg–Zn alloy sheet. Thus, the elongation to fracture of the NA alloy sheet was improved compared to that of the AA alloy sheet because of the enhanced work-hardening capacity and the thin precipitate-free zone (PFZ). Deformation textures and dislocation densities varied between NA and AA treatments, as revealed by electron backscatter diffraction (EBSD) and kernel average misorientation (KAM) analysis. The interactions between the precipitates, dislocations, and the PFZ in the AA- and NA-treated alloys were analyzed via transmission electron microscopy (TEM). The insights gained from this research provide a valuable foundation for industrial applications, particularly in sectors demanding lightweight, high-strength materials, where optimizing the aging process can lead to significant performance improvement and cost savings.
- 8 May 2024
- Published by Springer Nature in Metals and Materials International
- Vol. 30 (10) , 2734-2744
Development of Particle and Grain Uniformity in High-Ductility Al–Zn–Mg Alloys with the Addition of Mg and Cu
- 8 May 2024
- Published by Springer Nature in Metals and Materials International
- Vol. 30 (10) , 2734-2744
Development of Particle and Grain Uniformity in High-Ductility Al–Zn–Mg Alloys with the Addition of Mg and Cu
- 11 February 2023
- Published by Springer Nature
- p. 89-98
Enhancing Reinforcing Efficiency of SiC Particles in Aluminum Matrix Composites with Intercalated Oxygen Atoms
- 11 February 2023
- Published by Springer Nature
- p. 89-98
Enhancing Reinforcing Efficiency of SiC Particles in Aluminum Matrix Composites with Intercalated Oxygen Atoms
- Open Access
Molecular Dynamics Study on Crack Propagation in Al Containing Mg–Si Clusters Formed during Natural Aging
The crack propagation behavior of Al containing Mg–Si clusters is investigated using molecular dynamics (MD) simulations to demonstrate the relationship between the natural aging time in Al–Si–Mg alloys and ductility. Experimental results show that the elongation at failure decreases with natural aging. There are few studies on the relationship between natural aging and ductility because of the difficult observation of Mg–Si clusters. To solve the difficulty, cracked Al containing Mg–Si clusters of varying sizes are assumed for the MD simulations. A larger Mg–Si cluster in Al results in earlier crack opening and dislocation emission. Moreover, as the Mg–Si cluster size increases, the stress near the crack tip becomes more concentrated. This causes rapid crack propagation, a similar effect to that of crack tip sharpening. As a result of long-term natural aging, the cracks expand rapidly. The influence of geometry is also investigated. Crack lengthening and thickness reduction negatively impact the fracture toughness, with the former having a larger impact than the latter. Although there are several discrepancies in the practical deformation conditions, the simulation results can help to more thoroughly understand natural aging in Al–Si–Mg alloys.
Open AccessMolecular Dynamics Study on Crack Propagation in Al Containing Mg–Si Clusters Formed during Natural Aging
The crack propagation behavior of Al containing Mg–Si clusters is investigated using molecular dynamics (MD) simulations to demonstrate the relationship between the natural aging time in Al–Si–Mg alloys and ductility. Experimental results show that the elongation at failure decreases with natural aging. There are few studies on the relationship between natural aging and ductility because of the difficult observation of Mg–Si clusters. To solve the difficulty, cracked Al containing Mg–Si clusters of varying sizes are assumed for the MD simulations. A larger Mg–Si cluster in Al results in earlier crack opening and dislocation emission. Moreover, as the Mg–Si cluster size increases, the stress near the crack tip becomes more concentrated. This causes rapid crack propagation, a similar effect to that of crack tip sharpening. As a result of long-term natural aging, the cracks expand rapidly. The influence of geometry is also investigated. Crack lengthening and thickness reduction negatively impact the fracture toughness, with the former having a larger impact than the latter. Although there are several discrepancies in the practical deformation conditions, the simulation results can help to more thoroughly understand natural aging in Al–Si–Mg alloys.
- 12 November 2022
- Published by Springer Nature in Metals and Materials International
- Vol. 29 (6) , 1684-1698
Influence of Cu and Mg Content on Recrystallization Behavior in Al–Zn–Mg–Cu-Based Alloy Sheets
- 12 November 2022
- Published by Springer Nature in Metals and Materials International
- Vol. 29 (6) , 1684-1698
Influence of Cu and Mg Content on Recrystallization Behavior in Al–Zn–Mg–Cu-Based Alloy Sheets
- Open Access
Influence of the Composition and Vacancy Concentration on Cluster Decomposition Behavior in Al–Si–Mg Alloy: A Kinetic Monte Carlo Study
The influence of cluster composition and the addition of vacancies on the decomposition behavior of clusters during artificial aging in Al–Si–Mg alloys were analyzed according to the kinetic Montel Carlo model. Clusters with a balanced composition (Mg/(Mg + Si) = 0.5) were the most difficult to decompose. In addition, the cluster decomposition was slower when more vacancies were added to the cluster. Among Si, Mg, and vacancies, vacancies most significantly affect decomposition. The clusters with Mg/(Mg + Si) ≤ 0.4 strongly trap vacancies, which can be classified as hardly decomposable vacancy-rich clusters. The clustering behavior during natural aging and the effect of pre-aging were analyzed using the Kinetic Monte Carlo model. Pre-aging slows down cluster formation due to the lowered vacancy concentration. In addition, the overall composition of the clusters changes to easily decomposable clusters after pre-aging. Thus, not only is the number of clusters reduced but also the clusters are more easily decomposable when pre-aging is performed.
Open AccessInfluence of the Composition and Vacancy Concentration on Cluster Decomposition Behavior in Al–Si–Mg Alloy: A Kinetic Monte Carlo Study
The influence of cluster composition and the addition of vacancies on the decomposition behavior of clusters during artificial aging in Al–Si–Mg alloys were analyzed according to the kinetic Montel Carlo model. Clusters with a balanced composition (Mg/(Mg + Si) = 0.5) were the most difficult to decompose. In addition, the cluster decomposition was slower when more vacancies were added to the cluster. Among Si, Mg, and vacancies, vacancies most significantly affect decomposition. The clusters with Mg/(Mg + Si) ≤ 0.4 strongly trap vacancies, which can be classified as hardly decomposable vacancy-rich clusters. The clustering behavior during natural aging and the effect of pre-aging were analyzed using the Kinetic Monte Carlo model. Pre-aging slows down cluster formation due to the lowered vacancy concentration. In addition, the overall composition of the clusters changes to easily decomposable clusters after pre-aging. Thus, not only is the number of clusters reduced but also the clusters are more easily decomposable when pre-aging is performed.
- 28 January 2018
- Published by Springer Nature
- p. 99-104
Strengthening and Toughening Behaviors of the Mg–9Al Alloy Containing Oxygen Atoms
- 28 January 2018
- Published by Springer Nature
- p. 99-104
Strengthening and Toughening Behaviors of the Mg–9Al Alloy Containing Oxygen Atoms
- 30 July 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 674, 91-97
Effect of wrapped Zn plate on the densification of Al-MWCNTs composites produced by cold pressing and liquid phase sintering
- 30 July 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 674, 91-97
Effect of wrapped Zn plate on the densification of Al-MWCNTs composites produced by cold pressing and liquid phase sintering
- Open Access
- 15 March 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 23184
Multi-functional magnesium alloys containing interstitial oxygen atoms
A new class of magnesium alloys has been developed by dissolving large amounts of oxygen atoms into a magnesium lattice (Mg-O alloys). The oxygen atoms are supplied by decomposing titanium dioxide nanoparticles in a magnesium melt at 720 °C; the titanium is then completely separated out from the magnesium melt after solidification. The dissolved oxygen atoms are located at the octahedral sites of magnesium, which expand the magnesium lattice. These alloys possess ionic and metallic bonding characteristics, providing outstanding mechanical and functional properties. A Mg-O-Al casting alloy made in this fashion shows superior mechanical performance, chemical resistance to corrosion, and thermal conductivity. Furthermore, a similar Mg-O-Zn wrought alloy shows high elongation to failure (>50%) at room temperature, because the alloy plastically deforms with only multiple slips in the sub-micrometer grains (<300 nm) surrounding the larger grains (~15 μm). The metal/non-metal interstitial alloys are expected to open a new paradigm in commercial alloy design.
- 15 March 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 23184
Open AccessMulti-functional magnesium alloys containing interstitial oxygen atoms
A new class of magnesium alloys has been developed by dissolving large amounts of oxygen atoms into a magnesium lattice (Mg-O alloys). The oxygen atoms are supplied by decomposing titanium dioxide nanoparticles in a magnesium melt at 720 °C; the titanium is then completely separated out from the magnesium melt after solidification. The dissolved oxygen atoms are located at the octahedral sites of magnesium, which expand the magnesium lattice. These alloys possess ionic and metallic bonding characteristics, providing outstanding mechanical and functional properties. A Mg-O-Al casting alloy made in this fashion shows superior mechanical performance, chemical resistance to corrosion, and thermal conductivity. Furthermore, a similar Mg-O-Zn wrought alloy shows high elongation to failure (>50%) at room temperature, because the alloy plastically deforms with only multiple slips in the sub-micrometer grains (<300 nm) surrounding the larger grains (~15 μm). The metal/non-metal interstitial alloys are expected to open a new paradigm in commercial alloy design.