Kristien De Sitter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kristien De Sitter has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Bart Van der Bruggen
KU Leuven
2 shared publications - Chris Dotremont
VITO-Flemish Institute for Technological Research, Boeretang 200, 2400 Mol, Belgium
2 shared publications - Lies Eykens
Separation and Conversion Technology, VITO (Flemish Institute for Technological Research), Boeretang 200, B-2400 Mol, Belgium
2 shared publications - Luc Pinoy
Department of Chemical Engineering, Cluster Sustainable Chemical Process Technology, KU Leuven, Gebroeders Desmetstraat 1, B-9000 Ghent, Belgium
2 shared publications Anita Buekenhoudt
Materials and Chemistry (MATCH), Belgium
1 shared publication- Anita Buekenhoudt
Unit Materials & Chemistry (MatCh), Flemish Institute for Technological Research (VITO), Boeretang 200, 2400 Mol, Belgium
1 shared publication
Latest Publications
- Open Access
- 13 June 2026
- Published by MDPI AG in Separations
- Vol. 13 (6) , 176
Breaking Recovery Bottlenecks in Long-Chain Dicarboxylic Acid Extraction: Effect of pH and Solvents
Efficient recovery of long-chain dicarboxylic acids (LCDAs) from aqueous fermentation broths is a key challenge for the industrial development of bio-based LCDA production. This study evaluates liquid–liquid extraction (LLE) as a downstream recovery strategy, comparing physical extraction (PE) and reactive extraction (RE) for DCA 12, DCA 16, and DCA 18. The novelty of this work lies in demonstrating that LCDA extraction is governed by mechanisms fundamentally different from those of short- and medium-chain dicarboxylic acids. Whereas shorter chain dicarboxylic acids are mainly controlled by dissociation degree, LCDA recovery is strongly influenced by carbon-chain apolarity, low aqueous solubility, and compound losses through agglomeration, precipitation, and/or micellization. PEs enabled the selective recovery of the more hydrophobic DCA 16 and DCA 18 over DCA 12, confirming the dominant role of chain length in LCDA separation. In contrast, RE with Aliquat®336 maximized total LCDA recovery, achieving extraction efficiencies above 85%, but with reduced selectivity. Validation in autoclaved fermentation broth from UCO feedstock confirmed the potential of Aliquat®336 in octanol for high LCDA recovery, while revealing lower extraction efficiencies than in model mixtures due to broth matrix complexity. Overall, this study establishes LLE as a promising platform for LCDA recovery and highlights that future downstream process design must balance total recovery, chain-length selectivity, and broth-specific matrix effects.
- 13 June 2026
- Published by MDPI AG in Separations
- Vol. 13 (6) , 176
Open AccessBreaking Recovery Bottlenecks in Long-Chain Dicarboxylic Acid Extraction: Effect of pH and Solvents
Efficient recovery of long-chain dicarboxylic acids (LCDAs) from aqueous fermentation broths is a key challenge for the industrial development of bio-based LCDA production. This study evaluates liquid–liquid extraction (LLE) as a downstream recovery strategy, comparing physical extraction (PE) and reactive extraction (RE) for DCA 12, DCA 16, and DCA 18. The novelty of this work lies in demonstrating that LCDA extraction is governed by mechanisms fundamentally different from those of short- and medium-chain dicarboxylic acids. Whereas shorter chain dicarboxylic acids are mainly controlled by dissociation degree, LCDA recovery is strongly influenced by carbon-chain apolarity, low aqueous solubility, and compound losses through agglomeration, precipitation, and/or micellization. PEs enabled the selective recovery of the more hydrophobic DCA 16 and DCA 18 over DCA 12, confirming the dominant role of chain length in LCDA separation. In contrast, RE with Aliquat®336 maximized total LCDA recovery, achieving extraction efficiencies above 85%, but with reduced selectivity. Validation in autoclaved fermentation broth from UCO feedstock confirmed the potential of Aliquat®336 in octanol for high LCDA recovery, while revealing lower extraction efficiencies than in model mixtures due to broth matrix complexity. Overall, this study establishes LLE as a promising platform for LCDA recovery and highlights that future downstream process design must balance total recovery, chain-length selectivity, and broth-specific matrix effects.
- Open Access
- 20 November 2024
- Published by Frontiers Media SA in Frontiers in Chemical Engineering
- Vol. 6, 1449088
Application of tight membrane extraction for amines separation
Chiral amines are very valued constituents of many important pharmaceutical compounds and their intermediates. However, the production of a chiral amine encounters some challenges, like the use of harsh conditions and the unfavorable thermodynamic equilibrium. In this research the possibilities of tight membrane extraction (ME) for amines separation has been investigated to improve the reaction equilibrium. A specific transaminase reaction was selected for the study in which product amine 1-methyl-3-phenylpropylamine (MPPA) or methyl benzylamine (MBA) needs to be separated from the donor amine isopropylamine (IPA). Tight ME is an innovative separation process in which the membrane is not only an interface, but also a way to add extra selectivity to the process. In the present work, we thoroughly discuss the main factors influencing this novel technique by evaluating the extraction efficiency and extraction rates for the different amines. Then we also determine the optimal parameters for the selected reaction. Supported liquid membrane extraction (SLM), as well as pressure driven filtration, more specifically, nanofiltration (NF), were also studied as benchmark technologies, showing that tight ME has a greater advantage over the two in this specific case, due to the extra affinity factor offered by the membrane. The selectivity of MPPA/IPA in tight ME for the optimized parameters was significantly higher than for SLM and NF.
- 20 November 2024
- Published by Frontiers Media SA in Frontiers in Chemical Engineering
- Vol. 6, 1449088
Open AccessApplication of tight membrane extraction for amines separation
Chiral amines are very valued constituents of many important pharmaceutical compounds and their intermediates. However, the production of a chiral amine encounters some challenges, like the use of harsh conditions and the unfavorable thermodynamic equilibrium. In this research the possibilities of tight membrane extraction (ME) for amines separation has been investigated to improve the reaction equilibrium. A specific transaminase reaction was selected for the study in which product amine 1-methyl-3-phenylpropylamine (MPPA) or methyl benzylamine (MBA) needs to be separated from the donor amine isopropylamine (IPA). Tight ME is an innovative separation process in which the membrane is not only an interface, but also a way to add extra selectivity to the process. In the present work, we thoroughly discuss the main factors influencing this novel technique by evaluating the extraction efficiency and extraction rates for the different amines. Then we also determine the optimal parameters for the selected reaction. Supported liquid membrane extraction (SLM), as well as pressure driven filtration, more specifically, nanofiltration (NF), were also studied as benchmark technologies, showing that tight ME has a greater advantage over the two in this specific case, due to the extra affinity factor offered by the membrane. The selectivity of MPPA/IPA in tight ME for the optimized parameters was significantly higher than for SLM and NF.
- Open Access
- 20 June 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (6) , 637
Functionalization of a Hydrophilic Commercial Membrane Using Inorganic-Organic Polymers Coatings for Membrane Distillation
Membrane distillation is a thermal separation technique using a microporous hydrophobic membrane. One of the concerns with respect to the industrialization of the technique is the development of novel membranes. In this paper, a commercially available hydrophilic polyethersulfone membrane with a suitable structure for membrane distillation was modified using available hydrophobic coatings using ORMOCER® technology to obtain a hydrophobic membrane that can be applied in membrane distillation. The surface modification was performed using a selection of different components, concentrations, and application methods. The resulting membranes can have two hydrophobic surfaces or a hydrophobic and hydrophilic surface depending on the application method. An extensive characterization procedure confirmed the suitability of the coating technique and the obtained membranes for membrane distillation. The surface contact angle of water could be increased from 27° up to 110°, and fluxes comparable to membranes commonly used for membrane distillation were achieved under similar process conditions. A 100 h test demonstrated the stability of the coating and the importance of using sufficiently stable base membranes.
- 20 June 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (6) , 637
Open AccessFunctionalization of a Hydrophilic Commercial Membrane Using Inorganic-Organic Polymers Coatings for Membrane Distillation
Membrane distillation is a thermal separation technique using a microporous hydrophobic membrane. One of the concerns with respect to the industrialization of the technique is the development of novel membranes. In this paper, a commercially available hydrophilic polyethersulfone membrane with a suitable structure for membrane distillation was modified using available hydrophobic coatings using ORMOCER® technology to obtain a hydrophobic membrane that can be applied in membrane distillation. The surface modification was performed using a selection of different components, concentrations, and application methods. The resulting membranes can have two hydrophobic surfaces or a hydrophobic and hydrophilic surface depending on the application method. An extensive characterization procedure confirmed the suitability of the coating technique and the obtained membranes for membrane distillation. The surface contact angle of water could be increased from 27° up to 110°, and fluxes comparable to membranes commonly used for membrane distillation were achieved under similar process conditions. A 100 h test demonstrated the stability of the coating and the importance of using sufficiently stable base membranes.
- Open Access
- 25 January 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (2) , 118
Wetting Resistance of Commercial Membrane Distillation Membranes in Waste Streams Containing Surfactants and Oil
Water management is becoming increasingly challenging and several technologies, including membrane distillation (MD) are emerging. This technology is less affected by salinity compared to reverse osmosis and is able to treat brines up to saturation. The focus of MD research recently shifted from seawater desalination to industrial applications out of the scope of reverse osmosis. In many of these applications, surfactants or oil traces are present in the feed stream, lowering the surface tension and increasing the risk for membrane wetting. In this study, the technological boundaries of MD in the presence of surfactants are investigated using surface tension, contact angle and liquid entry pressure measurements together with lab-scale MD experiments to predict the wetting resistance of different membranes. Synthetic NaCl solutions mixed with sodium dodecyl sulfate (SDS) were used as feed solution. The limiting surfactant concentration was found to be dependent on the surface chemistry of the membrane, and increased with increasing hydrophobicity and oleophobicity. Additionally, a hexadecane/SDS emulsion was prepared with a composition simulating produced water, a waste stream in the oil and gas sector. When hexadecane is present in the emulsion, oleophobic membranes are able to resist wetting, whereas polytetrafluoretheen (PTFE) is gradually wetted by the feed liquid.
- 25 January 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (2) , 118
Open AccessWetting Resistance of Commercial Membrane Distillation Membranes in Waste Streams Containing Surfactants and Oil
Water management is becoming increasingly challenging and several technologies, including membrane distillation (MD) are emerging. This technology is less affected by salinity compared to reverse osmosis and is able to treat brines up to saturation. The focus of MD research recently shifted from seawater desalination to industrial applications out of the scope of reverse osmosis. In many of these applications, surfactants or oil traces are present in the feed stream, lowering the surface tension and increasing the risk for membrane wetting. In this study, the technological boundaries of MD in the presence of surfactants are investigated using surface tension, contact angle and liquid entry pressure measurements together with lab-scale MD experiments to predict the wetting resistance of different membranes. Synthetic NaCl solutions mixed with sodium dodecyl sulfate (SDS) were used as feed solution. The limiting surfactant concentration was found to be dependent on the surface chemistry of the membrane, and increased with increasing hydrophobicity and oleophobicity. Additionally, a hexadecane/SDS emulsion was prepared with a composition simulating produced water, a waste stream in the oil and gas sector. When hexadecane is present in the emulsion, oleophobic membranes are able to resist wetting, whereas polytetrafluoretheen (PTFE) is gradually wetted by the feed liquid.