M. A. Kamal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
M. A. Kamal has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
F. Khan
Department of Chemical Tech./Eng., University of Karachi, 75270, Karachi - Pakistan
1 shared publicationS. Amber
Department of Applied Chemistry and Chemical Technology, University of Karachi, Karachi, Pakistan
1 shared publication
Latest Publications
- 15 November 2018
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 37 (2) , 146-154
Production of hydrocarbons by catalytic cracking of stearic acid under atmospheric pressure for petrochemical replacement
Catalytic cracking of stearic acid (FFA) was carried out at atmospheric pressure to obtain short chain hydrocarbons for petrochemical replacement using alumina, sodium carbonate and hydrated magnesium carbonate (HMC) as a catalyst. All the three catalysts not only reduced the temperature but also the time required for cracking from 500 to 340 °C and 5 to 1:45 hours respectively. Cracking adopted the similar mechanism carried out in previous studies proven by the presence of n-alkane, alkene and carboxylic acid series with small amounts of aldehydes and ketones identified through Gas chromatography-Mass spectroscopy analysis. HMC was found a better catalyst regarding hydrocarbon formation produced 60.607 mole percent hydrocarbons at 350 °C using 10:1 (w/w) acid to catalyst mass ratio. HMC formed all hydrocarbons from C12-C17 in lesser cracking time 1:45 hours.
- 15 November 2018
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 37 (2) , 146-154
Production of hydrocarbons by catalytic cracking of stearic acid under atmospheric pressure for petrochemical replacement
Catalytic cracking of stearic acid (FFA) was carried out at atmospheric pressure to obtain short chain hydrocarbons for petrochemical replacement using alumina, sodium carbonate and hydrated magnesium carbonate (HMC) as a catalyst. All the three catalysts not only reduced the temperature but also the time required for cracking from 500 to 340 °C and 5 to 1:45 hours respectively. Cracking adopted the similar mechanism carried out in previous studies proven by the presence of n-alkane, alkene and carboxylic acid series with small amounts of aldehydes and ketones identified through Gas chromatography-Mass spectroscopy analysis. HMC was found a better catalyst regarding hydrocarbon formation produced 60.607 mole percent hydrocarbons at 350 °C using 10:1 (w/w) acid to catalyst mass ratio. HMC formed all hydrocarbons from C12-C17 in lesser cracking time 1:45 hours.
- Open Access
- 19 February 2009
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 64 (2) , 191-197
Effect of Extraction and Adsorption on Re-refining of Used Lubricating Oil
Solvent extraction followed by adsorption has been found to be one of the competitive processes for recycling of waste lubricating oil. In this paper, the performance of various solvents for sludge formation has been studied. 1-butanol produced maximum sludge followed by methyl ethyl ketone (MEK), 1-hexanol and 2-butanol. The difference in sludge formation between 1-butanol and MEK was only 0.3%. However due to low boiling point and low cost, MEK was preferred over 1-butanol. The extracted oil was then passed through a column of different adsorbents. An oil of colour index (yellow) 2, carbon residue 0.14%, sulphated ash 0.02% and flash point 216°C, was obtained with 94% yield. L'extraction par solvant suivie d'adsorption est considérée comme l'un des procédés les plus performants pour le recyclage des huiles usagées. Dans cet article, la performance de divers solvants pour la formation de boues a été étudiée. Le 1-butanol produit le plus de boues, suivi de la méthyle éthyle cétone (MEK), puis du 1-hexanol et du 2-butanol. La différence de formation des boues n'est que de 0,3 % entre le 1-butanol et le MEK. Cependant, en raison de son faible point d'ébullition et de son faible coût, le MEK a été préféré au 1-butanol. L'huile extraite est ensuite passée à travers une colonne de différents adsorbants. Une huile d'indice de couleur 2 (jaune), à 0,14 % de résidu de carbone, 0,02 % de cendres sulfatées et 216 °C de point d'éclair, a été obtenue avec 94 % de rendement.
- 19 February 2009
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 64 (2) , 191-197
Open AccessEffect of Extraction and Adsorption on Re-refining of Used Lubricating Oil
Solvent extraction followed by adsorption has been found to be one of the competitive processes for recycling of waste lubricating oil. In this paper, the performance of various solvents for sludge formation has been studied. 1-butanol produced maximum sludge followed by methyl ethyl ketone (MEK), 1-hexanol and 2-butanol. The difference in sludge formation between 1-butanol and MEK was only 0.3%. However due to low boiling point and low cost, MEK was preferred over 1-butanol. The extracted oil was then passed through a column of different adsorbents. An oil of colour index (yellow) 2, carbon residue 0.14%, sulphated ash 0.02% and flash point 216°C, was obtained with 94% yield. L'extraction par solvant suivie d'adsorption est considérée comme l'un des procédés les plus performants pour le recyclage des huiles usagées. Dans cet article, la performance de divers solvants pour la formation de boues a été étudiée. Le 1-butanol produit le plus de boues, suivi de la méthyle éthyle cétone (MEK), puis du 1-hexanol et du 2-butanol. La différence de formation des boues n'est que de 0,3 % entre le 1-butanol et le MEK. Cependant, en raison de son faible point d'ébullition et de son faible coût, le MEK a été préféré au 1-butanol. L'huile extraite est ensuite passée à travers une colonne de différents adsorbants. Une huile d'indice de couleur 2 (jaune), à 0,14 % de résidu de carbone, 0,02 % de cendres sulfatées et 216 °C de point d'éclair, a été obtenue avec 94 % de rendement.