PRPascal Ray

Pascal Ray

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Pascal Ray has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A comparative study of construction methods for seismic fragility curves using numerical simulations

    by Thien-Phu Le, Cong-Thuat Dang, Pascal Ray

    A seismic fragility curve of a structure or a mechanical system, presenting its failure probability versus seismic intensity, can be established by an engineering judgment approach, an empirical approach or a numerical approach. In the numerical approach, there exist three popular methods: the scaled seismic intensity method, the maximum likelihood estimation method, and the probabilistic seismic demand/capacity models. This paper is focused on a comparison of these numerical methods. Linear/non-linear oscillators and an eight-storey frame structure were used to derive fragility curves for different tests. The results obtained show a discrepancy of fragility curves between the methods, and their quality is commented in comparison with results of the Monte-Carlo method with a high number of simulations. The maximum likelihood estimation method is in general the recommended method, due to its good accuracy in both numerical examples.


  • Prédiction du comportement dynamique du système de forage grande vitesse vibratoire

    by Fabien Forestier, Vincent Gagnol, Pascal Ray, Henry Paris

    Le Forage Grande Vitesse Vibratoire (FGVV) est un nouveau procédé de perçage qui permet de tripler la productivité des perçages profonds en supprimant les cycles d’évacuation des copeaux ainsi que la lubrification. Pour cela un porte-outil spécifique aété développé, qui entre en vibrations axiales auto-entretenues lors de la coupe et permet le fractionnement du copeau, facilitant ainsi sonévacuation. Pour anticiper uneéventuelle diminution de la durée de vie des roulements à billes de l’électrobroche résultant de ces vibrations, un modèle global du comportement dynamique du système tête vibratoire-électrobroche est présenté. Ce modèle est basé sur la modélisation du comportement des entités structurales par deséléments-finis de type « poutre-rotor» prenant en compte les effets dynamiques associés aux hautes fréquences de rotations de l’électrobroche, couplé à des modèles d’interfaces identifiés par la méthode de couplage de réceptance. Le modèle est validé à l’aide d’expérimentations qui montrent une bonne correspondance entre les résultats expérimentaux et numériques. Le modèle est ensuite utilisé pour calculer la durée de vie des roulements à billes de l’électrobroche lors de différentes opérations de perçage. L’influence de la fréquence de rotation et de l’avance sur la durée de vie des roulements estétudiée, permettant ainsi de faire ressortir des plages de fonctionnement optimal. High speed vibratory drilling increases the productivity of small diameters deep holes without retreat cycles and lubricant. A specific tool-holder which induces self-sustained vibrations of the mobile part of the vibratory head, breaks up chips and ensures their disposal. To anticipate potential risks associated with these vibrations, a global model of the dynamic behavior of the system (head vibratory-spindle) will be performed. This model is based on the modelisation of the dynamic behavior of the entities throught a rotor-beam element which takes into account the gyroscopic effect and centrifugal forces; associated with interface modelisation identified throught the receptance coupling method. The development and the validation of the dynamic behavior model of the entity are presented. Then, the identification procedure of the interface’s dynamic behavior is exposed. Finally, the assembled model is obtained, and used for bearings lifespan prediction during machining. The influence of spindle’s speed revolution and machine’s feed rate on the rolling bearings lifespan is highlighted. Optimized cutting conditions recommandations are made.


  • 57636 Numerical and Experimental High Speed Machining Spindle-Tool Modal characterization(Dynamics of Machine Components)

    by Vincent Gagnol, Thien-Phu LE, Pascal Ray

    The accurate knowledge of High-speed motorized spindle dynamic behavior during machining is important in order to ensure the reliability of machine tools in service and the quality of machined parts. More specifically, the prediction of stable cutting regions, which is a critical requirement for high-speed milling operations, requires accurate estimation of tool/holder/spindle set dynamic modal parameters. These estimations are generally obtained through the Frequency Response Function (FRF) measurements of the non-rotating spindle. However, significant changes in modal parameters are expected to change during operation due to spindle high-speed rotation. The spindle modal variations are highlighted through an integrated dynamic high-speed spindle-bearing system finite element model taking into account rotor dynamics effects. The dependency of dynamic behavior on speed range is then investigated and determined with accuracy. The objective of the proposed paper is to validate these numerical results through an experimental-based approach. Hence, an experimental set up is elaborated to measure the rotating tool vibration during machining operation in order to measure the spindle modal frequencies variation with respect to spindle speed in an industrial environment. The identification of spindle natural frequencies under rotating condition is challenging due to the low number of sensors and the presence of many harmonics in the measured signals. In order to overcome the mentioned issues and to extract characteristics of the system, the spindle modes are determined through a 3 step procedure. First, spindle modes are highlighted using the Frequency Domain Decomposition (FDD) technique with a new formulation at the considered rotating speed. These identified modes are then analyzed through the value of their respective damping ratio in order to separate harmonics component from structural spindle natural frequencies. Finally, the stochastic properties of the modes are also investigated by considering the probability density of the retained modes. Results show a good correlation between numerical and experimental-based identified frequencies. The spindle-tool identified modal properties during machining allow considering the numeric model to be well representative of real dynamic effects during machining. Using this model, a new stability lobe diagram is proposed. By integrating the predicted model in the chatter vibration stability law, which indicates whether the design would lead to a chatter vibration-free cutting operation, accurate spindle cutting conditions can be predicted.


  • Stability-Based Spindle Design Optimization

    by Vincent Gagnol, Belhassen C. Bouzgarrou, Pascal Ray, Christian Barra

    Prediction of stable cutting regions is a critical requirement for high-speed milling operations. These predictions are generally made using frequency-response measurements of the tool-holder-spindle set obtained from a nonrotating spindle. However, significant changes in system dynamics occur during high-speed rotation. In this paper, a dynamic high-speed spindle-bearing system model is elaborated on the basis of rotor dynamics prediction and readjusted on the basis of experimental modal identification. The dependency of dynamic behavior on speed range is then investigated and determined with accuracy. Dedicated experiments are carried out in order to confirm model results. They show that dynamic effects due to high rotational speed and elastic deformations, such as gyroscopic coupling and spin softening, have a significant influence on spindle behavior. By integrating the modeled speed-dependent spindle transfer function in the chatter vibration stability approach of Altintas and Budak (1995, CIRPS Ann, 44(1), pp. 357–362), a new dynamic stability lobe diagram is predicted. Significant changes are observed in the stability limits constructed using the proposed approach and allow accurate prediction of cutting conditions to be established. Finally, optimization studies are performed on spindle design parameters in order to obtain a chatter vibration-free cutting operation at the desired speed and depth of cut for a given cutter.


  • Measuring the Deformation of a Parallel Kinematics Machine under Dynamic Conditions, by Combining Video and Accelerometers

    by Tony Cano, Frederic Chapelle, Pascal Ray, Jean-Marc Lavest

    Parallel structure machines are a means to reach higher acceleration capacities, and thus significant reductions in machining time. But this contribution implies having light structures, leading to significant deformations in dynamic conditions. Based on a prototype built at IFMA and its numerical model, this article shows first the influence of elastic deformations on actuator efforts. In order to validate the numerical model or any other model which takes flexibilities into account, we propose the concept of a dynamic metrology tool, capable of measuring the deformations of the machine's different components during machining movements. This is a hybrid tool built around a camera and an accelerometer. Experimental progress is then described, particularly the work leading to the improvement of camera detection accuracy. The precision obtained to date is 0.02 mm with one target in a field of 300 mm. It can theoretically reach 0.01 mm with three targets instead of one