Vincent Gagnol
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Vincent Gagnol has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
P. Ray
MINES Saint-Etienne
8 shared publicationsPascal Ray
8 shared publications- Thien-Phu Le
LMEE, Université d’Évry Val-d’Essonne, Evry cedex, France
7 shared publications Belhassen C. Bouzgarrou
5 shared publications- Said Mousavi
Clermont Université, IFMA, Institut Pascal UMR 6602 UBP/CNRS/IFMA, BP 10448, 63000 Clermont-Ferrand, France
5 shared publications - Pascal Ray
Institut Pascal – Institut Français de Mécanique Avancée, Campus de Clermont-Ferrand, BP 265, 63175 Aubière Cedex, France
4 shared publications
Latest Publications
- Open Access
- 23 September 2026
- Published by EDP Sciences in Mechanics & Industry
- Vol. 27, 47
Dynamic characterization and homogenized modeling of hybrid metal–composite rotating shafts
This paper investigates the dynamic behavior of fully composite and hybrid metal–composite rotating shafts, including the effects of internal damping. The objective is to improve the performance of high-speed rotating shafts by proposing hybrid metal–composite designs as alternatives to conventional metallic shafts, in order to reduce vibration levels, shift critical speeds, and enhance damping capacity. A shell-based finite element model of a rotating laminated shaft was developed in ANSYS Workbench using the ACP module, accounting for internal damping via Rayleigh coefficients, rotary inertia, and gyroscopic effects. Due to ANSYS limitations in capturing gyroscopic effects in multilayered structures, Classical Laminate Theory (CLT) was used to homogenize multilayer configurations into equivalent single-layer shell elements. Experimental modal analysis was conducted to validate the numerical model at rest and to estimate the modal damping ratio for each mode. Then, the dynamic response of a Laval–Jeffcott rotor was analyzed across a speed range of 0–4800 rad/s, considering fully metallic, multilayer composite, and various hybrid metal–composite configurations with different stacking sequences and fiber orientations. The results show that natural frequencies are highly sensitive to laminate parameters. Gyroscopic effects lead to mode splitting in higher-order modes. The proposed homogenized shell model provides a robust framework for the analysis of internally damped laminated rotating shafts and supports the design of optimized hybrid rotors with improved vibrational performance.
- 23 September 2026
- Published by EDP Sciences in Mechanics & Industry
- Vol. 27, 47
Open AccessDynamic characterization and homogenized modeling of hybrid metal–composite rotating shafts
This paper investigates the dynamic behavior of fully composite and hybrid metal–composite rotating shafts, including the effects of internal damping. The objective is to improve the performance of high-speed rotating shafts by proposing hybrid metal–composite designs as alternatives to conventional metallic shafts, in order to reduce vibration levels, shift critical speeds, and enhance damping capacity. A shell-based finite element model of a rotating laminated shaft was developed in ANSYS Workbench using the ACP module, accounting for internal damping via Rayleigh coefficients, rotary inertia, and gyroscopic effects. Due to ANSYS limitations in capturing gyroscopic effects in multilayered structures, Classical Laminate Theory (CLT) was used to homogenize multilayer configurations into equivalent single-layer shell elements. Experimental modal analysis was conducted to validate the numerical model at rest and to estimate the modal damping ratio for each mode. Then, the dynamic response of a Laval–Jeffcott rotor was analyzed across a speed range of 0–4800 rad/s, considering fully metallic, multilayer composite, and various hybrid metal–composite configurations with different stacking sequences and fiber orientations. The results show that natural frequencies are highly sensitive to laminate parameters. Gyroscopic effects lead to mode splitting in higher-order modes. The proposed homogenized shell model provides a robust framework for the analysis of internally damped laminated rotating shafts and supports the design of optimized hybrid rotors with improved vibrational performance.
- Open Access
- 7 July 2021
- Published by EDP Sciences in Mechanics & Industry
- Vol. 22, 38
A model-based control law for vibration reduction of serial robots with flexible joints
The presence of flexibilities in rotational joints can limit the kinematic performances of manipulators doing high speed tasks as Pick and Place. The problem addressed in this work concerns the vibration control of serial robots with flexible joints performing Pick and Place tasks in order to improve productivity. Based on a dynamic model of a robot with flexible joints, a model-based control law is proposed with its associated tuning methodology. The robot dynamic model is then the key point of our methodology. This dynamic model considers stiffness and damping of each flexible joint. To guarantee its accuracy, a geometrical and dynamic identification procedure is realized. The objective is to show the relevancy of the proposed approach which integrates joint flexibilities in the control law. Theoretical results based on a representative model are used to illustrate the benefit of this model-based control law compare to two other control strategies (Feedforward control and control dedicated to rigid structures). Finally, a sensitivity analysis of this control law is realized to quantify the impact of modelling error and conclude on the criticality of joint damping value on vibration decreasing.
- 7 July 2021
- Published by EDP Sciences in Mechanics & Industry
- Vol. 22, 38
Open AccessA model-based control law for vibration reduction of serial robots with flexible joints
The presence of flexibilities in rotational joints can limit the kinematic performances of manipulators doing high speed tasks as Pick and Place. The problem addressed in this work concerns the vibration control of serial robots with flexible joints performing Pick and Place tasks in order to improve productivity. Based on a dynamic model of a robot with flexible joints, a model-based control law is proposed with its associated tuning methodology. The robot dynamic model is then the key point of our methodology. This dynamic model considers stiffness and damping of each flexible joint. To guarantee its accuracy, a geometrical and dynamic identification procedure is realized. The objective is to show the relevancy of the proposed approach which integrates joint flexibilities in the control law. Theoretical results based on a representative model are used to illustrate the benefit of this model-based control law compare to two other control strategies (Feedforward control and control dedicated to rigid structures). Finally, a sensitivity analysis of this control law is realized to quantify the impact of modelling error and conclude on the criticality of joint damping value on vibration decreasing.
- 17 February 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 107 (1-2) , 527-533
Pose-dependent modal behavior of a milling robot in service
- 17 February 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 107 (1-2) , 527-533
Pose-dependent modal behavior of a milling robot in service
- 1 April 2019
- Published by Elsevier in Applied Acoustics
- Vol. 147, 64-71
Operational modal identification in the presence of harmonic excitation
- 1 April 2019
- Published by Elsevier in Applied Acoustics
- Vol. 147, 64-71
Operational modal identification in the presence of harmonic excitation
- 2 January 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (1-4) , 253-264
Modal identification of a machine tool structure during machining operations
- 2 January 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (1-4) , 253-264
Modal identification of a machine tool structure during machining operations
- 1 April 2018
- Published by Elsevier in Robotics and Computer-Integrated Manufacturing
- Vol. 50, 181-192
Stability optimization in robotic milling through the control of functional redundancies
- 1 April 2018
- Published by Elsevier in Robotics and Computer-Integrated Manufacturing
- Vol. 50, 181-192
Stability optimization in robotic milling through the control of functional redundancies
- Open Access
- 31 May 2017
- Published by Elsevier in Procedia CIRP
- Vol. 58, 269-274
Control of a Multi Degrees Functional Redundancies Robotic Cell for Optimization of the Machining Stability
- 31 May 2017
- Published by Elsevier in Procedia CIRP
- Vol. 58, 269-274
Open AccessControl of a Multi Degrees Functional Redundancies Robotic Cell for Optimization of the Machining Stability
- 22 May 2017
- Published by EDP Sciences in Mechanics & Industry
- Vol. 18 (3) , 309
Modelling and simulation of an harvester head mechanism
This paper presents an approach for modelling and simulating a harvester head mechanism in the delimbing process of hardwood stands. An original model of the mechanical transmission is developed which allows, in the early phases of design, sizing of actuators and structural elements but also the validation and optimization of the various stages of the logging operation. The considered type of trees is characterized by flexuous trunks and big branches. Hence, the current harvester heads are not enough efficient to process such trees. New designs of harvester head are required to overcome these problems. In order to predict the process performances associated to several novel architectures of harvester heads, in preliminary design stage, a modelling of the process is developed. It is based on parameterized tree models with realistic geometry. The global harvesting head model makes interact original sub-models representative of basics functions as feeding trunk into the head and cutting branches by knife. These models identified experimentally, allow a good prediction of the interactions between the different parts of the machine and trees. The modelling and simulation of harvester head mechanisms are implemented in a numerical multibody environment. Simulation results of the global model are in a good agreement with the observed behaviour of the real system and represent a design support tool to develop innovative concepts of harvester head.
- 22 May 2017
- Published by EDP Sciences in Mechanics & Industry
- Vol. 18 (3) , 309
Modelling and simulation of an harvester head mechanism
This paper presents an approach for modelling and simulating a harvester head mechanism in the delimbing process of hardwood stands. An original model of the mechanical transmission is developed which allows, in the early phases of design, sizing of actuators and structural elements but also the validation and optimization of the various stages of the logging operation. The considered type of trees is characterized by flexuous trunks and big branches. Hence, the current harvester heads are not enough efficient to process such trees. New designs of harvester head are required to overcome these problems. In order to predict the process performances associated to several novel architectures of harvester heads, in preliminary design stage, a modelling of the process is developed. It is based on parameterized tree models with realistic geometry. The global harvesting head model makes interact original sub-models representative of basics functions as feeding trunk into the head and cutting branches by knife. These models identified experimentally, allow a good prediction of the interactions between the different parts of the machine and trees. The modelling and simulation of harvester head mechanisms are implemented in a numerical multibody environment. Simulation results of the global model are in a good agreement with the observed behaviour of the real system and represent a design support tool to develop innovative concepts of harvester head.
- 1 October 2016
- Published by Springer Nature in Mechanisms and Machine Science
- p. 133-141
An Approach for Modelling Harvester Head Mechanism in the Harvesting Process of Hardwood Stands
- 1 October 2016
- Published by Springer Nature in Mechanisms and Machine Science
- p. 133-141
An Approach for Modelling Harvester Head Mechanism in the Harvesting Process of Hardwood Stands
- 1 October 2016
- Published by Springer Nature
- p. 379-387
Model-Based Stability Prediction of a Machining Robot
- 1 October 2016
- Published by Springer Nature
- p. 379-387
Model-Based Stability Prediction of a Machining Robot