Oscar Arias-Cuevas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oscar Arias-Cuevas has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
R. Lewis
University of Sheffield
2 shared publications- Zili Li
Delft University of Technology
2 shared publications Dik J. Schipper
Laboratory for Surface Technology and Tribology , Engineering Technology, Twente University , PO Box 217, 7500AE, Enschede, The Netherlands
1 shared publicationE. A. Gallardo-Hernández
The University of Sheffield
1 shared publicationRadu I. Popovici
Laboratory for Surface Technology and Tribology , Engineering Technology, Twente University , PO Box 217, 7500AE, Enschede, The Netherlands
1 shared publicationZ Li
Section of Road and Railway Engineering, Faculty of Civil Engineering and Geosciences, Delft University of Technology, CN Delft, The Netherlands
1 shared publication
Latest Publications
- 25 July 2011
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 226 (1) , 72-94
Field investigations into the performance of magnetic track brakes of an electrical multiple unit against slippery tracks. Part 2: Braking force and side effects
Part II of the field investigations focuses on the braking force and some possible side effects of the frequent use of magnetic track brakes (MTBs) against slippery tracks. In part I, the adhesion recovery using MTBs along contaminated rails has been presented. Field tests have been performed with the permanent MTB of an electrical multiple unit (EMU) in a stabling yard. Three types of contamination representative of slippery tracks have been employed, e.g. water, leaves, and grease. Tests with dry ‘clean’ rails have also been performed throughout the testing to obtain a reference of the braking force in the speed range 0–40 km/h. Furthermore, the braking performance of the EMU in different braking modes is analysed under the tested conditions. The surfaces of the brake shoes and the rails have been examined to analyse possible changes during the testing. The profile of rails and the mass loss of the brake shoes have also been measured in the tests to quantify the wear caused in the tests. Moreover, the possible negative effect of a passing MTB on the electrical insulation of an insulated rail joint has been examined by means of electrical measurements and visual inspection.
- 25 July 2011
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 226 (1) , 72-94
Field investigations into the performance of magnetic track brakes of an electrical multiple unit against slippery tracks. Part 2: Braking force and side effects
Part II of the field investigations focuses on the braking force and some possible side effects of the frequent use of magnetic track brakes (MTBs) against slippery tracks. In part I, the adhesion recovery using MTBs along contaminated rails has been presented. Field tests have been performed with the permanent MTB of an electrical multiple unit (EMU) in a stabling yard. Three types of contamination representative of slippery tracks have been employed, e.g. water, leaves, and grease. Tests with dry ‘clean’ rails have also been performed throughout the testing to obtain a reference of the braking force in the speed range 0–40 km/h. Furthermore, the braking performance of the EMU in different braking modes is analysed under the tested conditions. The surfaces of the brake shoes and the rails have been examined to analyse possible changes during the testing. The profile of rails and the mass loss of the brake shoes have also been measured in the tests to quantify the wear caused in the tests. Moreover, the possible negative effect of a passing MTB on the electrical insulation of an insulated rail joint has been examined by means of electrical measurements and visual inspection.
- 26 November 2010
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 48 (sup1) , 299-316
Simulation of curving behaviour under high traction in lubricated wheel–rail contacts
Migration of the flange lubricant to the top of the high rail may compromise the traction of a rail vehicle and affect its curving behaviour. In order to simulate this possible situation, a lubrication model has been coupled to commercial multi-body dynamics software to describe the tangential formulation of the lubricated high-rail contact. Different friction levels have been adopted for the low rail to study their influence on the curving behaviour and traction. Since the creep force in the wheel–rail contact approaches saturation of the friction, the traction control unit of the rail vehicle under study has also been modelled to account for the reduction of the wheel axle torque in the presence of wheel macro-slip.
- 26 November 2010
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 48 (sup1) , 299-316
Simulation of curving behaviour under high traction in lubricated wheel–rail contacts
Migration of the flange lubricant to the top of the high rail may compromise the traction of a rail vehicle and affect its curving behaviour. In order to simulate this possible situation, a lubrication model has been coupled to commercial multi-body dynamics software to describe the tangential formulation of the lubricated high-rail contact. Different friction levels have been adopted for the low rail to study their influence on the curving behaviour and traction. Since the creep force in the wheel–rail contact approaches saturation of the friction, the traction control unit of the rail vehicle under study has also been modelled to account for the reduction of the wheel axle torque in the presence of wheel macro-slip.
- Open Access
- 22 December 2009
- Published by Springer Nature in Tribology Letters
- Vol. 37 (3) , 623-635
Investigating the Lubricity and Electrical Insulation Caused by Sanding in Dry Wheel–Rail Contacts
- 22 December 2009
- Published by Springer Nature in Tribology Letters
- Vol. 37 (3) , 623-635
Open AccessInvestigating the Lubricity and Electrical Insulation Caused by Sanding in Dry Wheel–Rail Contacts
- Open Access
- 19 November 2008
- Published by Springer Nature in Tribology Letters
- Vol. 33 (2) , 97-109
Rolling–Sliding Laboratory Tests of Friction Modifiers in Leaf Contaminated Wheel–Rail Contacts
- 19 November 2008
- Published by Springer Nature in Tribology Letters
- Vol. 33 (2) , 97-109
Open AccessRolling–Sliding Laboratory Tests of Friction Modifiers in Leaf Contaminated Wheel–Rail Contacts