ABAnirban Bhattacharya

Anirban Bhattacharya

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Anirban Bhattacharya has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • FINITE ELEMENT ANALYSIS OF THERMAL AND MATERIAL FLOW BEHAVIOR DURING FRICTION STIR SPOT WELDING

    by Ashu Garg, Anirban Bhattacharya

    Friction stir spot welding (FSSW), a modified approach of solid-state welding process, is gaining importance due to its capability to join sheets that are difficult-to-weld by conventional methods like resistance welding process. In the present work, effects of tool rotational speed (1000, 1500, 2000 rpm), coefficient of friction (0.2, 0.3, 0.4) and tool pin profile (circular, square and triangular) are investigated on the heat generation and material flow behavior during FSSW process through finite (FE) analysis. FE results indicate that higher heat is generated for circular tool pin profile which further increases with tool rotational speed but decreases the width of bonded region. Temperature in the workpiece rises sharply as severe plastic deformation occurs during plunging of pin into the workpiece followed by a gradual rise with further penetration of tool pin. Another notable rise in temperature is observed as the shoulder region touches and deforms the workpiece wherein friction in radial surface starts contributing along with circumferential tool pin surface. Moderate increase in temperature is noticed with increase in the value of coefficient of friction for different tool pin geometries. The circular tool pin also shows the efficient symmetric mixing of material as compared to other tool pin profiles. Higher strain is generated for square tool pin due to more plastic deformation of metal and width of bonded region formed is also larger as compared to circular or triangular tool pin and thus improved the strength of welded joints formed by square pin tool. The FE predicted temperature is validated with reported literatures and observed to be in fair agreement.

  • Failure investigation of fused deposition modelling parts fabricated at different raster angles under tensile and flexural loading

    by Ashu Garg, Anirban Bhattacharya, Ajay Batish

    Fused deposition modelling is an efficient rapid prototyping process used to rapidly fabricate three-dimensional solid objects with complicated geometries. Many process parameters affect the fused deposition modelling process and their settings influence the quality of the specimen. This article investigates the effect of raster angle on surface roughness (along and across the length direction) and mechanical properties (tensile and flexural strength) of fused deposition modelling parts built at 10 different raster angles (0°–90° at 10° interval). All parts are built using acrylonitrile butadiene styrene P430 material. Surface roughness for circular and parabolic curved surfaces is also measured when specimens are built at different raster angles. Fracture surfaces are inspected with scanning electron microscope to study the modes of failure under different loading conditions. The samples where raster angle is 0° and layers are deposited along the length of the specimen exhibited optimal mechanical strength and good surface finish (when measured along the length). Scanning electron microscope results reveal that for 0° raster angle, failures are mainly due to pulling and rupture of fibres and for 30° and 60° raster angle, failure is due to brittle shear in a direction parallel to raster orientation. Due to the presence of number of heating and cooling cycle in 90° raster orientation, interlayer cracking and distortion of raster take place leading to lower strength.


  • Experimental Investigation of Magnetic Field Assisted Powder Mixed Electric Discharge Machining

    by Geeta Bhatt, Ajay Batish, Anirban Bhattacharya

    Electric discharge machining (EDM) is the most promising modern machining process amongst all the modern machining processes. This paper presents the application of metal powders that are mixed in dielectric medium during EDM to improve process performance like material removal, tool wear, surface finish, overcut, and microhardness. An external magnetic field is provided to further assist the machining process which affects differently for different output characteristics. Taguchi's design of experimentation and analysis of variance is used for analysis of results. Current, pulse on time, workpiece, and powders show significant effect on different responses Results showed that the material removal rate increases with the field strength at low values of current, while increase in overcut is observed with increase in field strength. Tool wear rate is observed to increase with the field strength at lower current values while microhardness is observed to enhance with increase in magnetic field strength. Surface finish is observed to improve at lower current with increase in field strength. Different optimal parameters are characterized for machining purpose in terms of current, powder, powder concentration, and tool for machining different workpiece materials. Results are further supported by selected microstructure and x-ray diffraction results.


  • Revisiting Arc, Metal Flow Behavior in Flux Activated Tungsten Inert Gas Welding

    by Anirban Bhattacharya

    Tungsten inert gas (TIG) welding is commonly used for quality joining of ferrous and non-ferrous materials. But lower depth of penetration is one major shortcoming of TIG and more numbers of passes are required for thick plate joining. Use of activated flux layer on workpiece remarkably enhances penetration. In the present work, arc and metal flow behavior are studied to revisit and validate the presence and role of governing forces responsible for higher penetration in flux activated TIG (ATIG) welding. Arc behavior, material flow patterns are studied during conventional and activated TIG welding for AISI 304 stainless steel using four different activated fluxes by carrying out welding (when arc is moving) as well as keeping the arc halted (stationary arc) for all cases. Results clearly demonstrate the presence of electromagnetic Lorentz force and surface tension induced reverse Marangoni flow (strongly centripetal). These forces also push the metal flow downward near the center region of the molten pool and in many occasions penetration reaches beyond plate thickness in ATIG welding.


  • Dissimilar Joining Between Austenitic and Duplex Stainless Steel in Double-Shielded GMAW: A Comparative Study

    by Anirban Bhattacharya, Ramesh Kumar

    In the present work, the effect of double-layer shielding and five other process parameters, namely welding voltage, current, primary shielding gas type, its flow rate, and filler material, is studied during dissimilar gas metal arc welding (GMAW) between austenitic and duplex stainless steels (SSs). A simple modification over the GMAW setup is made for additional supply of secondary shielding gas at different flow rates. Two different sets of welding are performed between austenitic and duplex SSs, i.e., AISI 304 with Duplex 2205 and AISI 316 with Duplex 2205, and the contributions of process parameters, their interactions on joint distortion, tensile strength, toughness, and fusion zone microhardness are evaluated. Improvements in joint quality due to the double-shielding environment are also highlighted. Double-layer shielding with secondary shielding by CO2 supply significantly improves tensile strength and toughness and reduces distortion. Fusion and interface zone microstructures are observed by scanning electron microscopy to study the metallurgical behavior of joints fabricated under single- and double-layer shielding environment.


  • Activated-TIG Welding of Different Steels: Influence of Various Flux and Shielding Gas

    by Surinder Tathgir, Anirban Bhattacharya

    In tungsten inert gas (TIG) welding, a low depth of penetration (DOP) is achieved during single pass. To achieve the required DOP, the speed of welding should be reduced; thus productivity reduces significantly. In this work, influence of 14 different oxide-, chloride-, and fluoride-based fluxes are evaluated on DOP and width-to-penetration ratio during flux-activated TIG (ATIG) welding of low alloy steel (AISI 4340), austenitic (AISI 304 and AISI 316) and duplex (Duplex 2205) stainless steels. The effect of welding current and three different shielding gas compositions is also studied during ATIG for these workpieces. Arc and weld metal pool behaviors are captured in order to study the physical behavior of the process. Results revealed that oxide-based fluxes like SiO2, MoO3, MoS2, CrO3, and TiO2 increases DOP significantly and in many cases through penetration (penetration reaches beyond plate thickness) is achieved. There is a noteworthy enhancement in penetration because of the addition of H2 in shielding gas. Addition of helium also helps to increase DOP. Arc behavior reveals the constriction of arc column during activated TIG welding, and positive surface tension-induced flow in centripetal (inward) direction is observed.


  • On Surface Finish and Dimensional Accuracy of FDM Parts after Cold Vapor Treatment

    by Ashu Garg, Anirban Bhattacharya, Ajay Batish

    Fused deposition modeling (FDM) process is an additive manufacturing technology where objects are manufactured in layers. In the present days, FDM is commercially used to build prototypes, functional components; however, these parts majorly suffer from poor surface quality and dimensional accuracy even for basic part geometries. In the present paper, first the effect of part deposition orientation on surface finish and dimensional accuracy of FDM parts are studied. The part selected for this study is designed in such a way that different primitive geometric features at different directions are present. The parts are built at different orientations (0°, 15°, 30°, 45°, 60°, 75°, 90°) using acrylonitrile butadiene styrene P430 material, and surface finish and dimensional accuracy are measured at different surfaces. Next, the FDM parts are postprocessed by cold vapor treatment of dimethylketone (acetone) and improvement in surface finish and change in dimensional accuracy are investigated. The results show that surface finish of the components is greatly improved by this vapor treatment process with minimal variations in part geometric accuracy after the treatment.


  • Mechanical and Metallurgical Studies in Double Shielded GMAW of Dissimilar Stainless Steels

    by Ramesh Kumar, Anirban Bhattacharya, Tarun Kumar Bera

    In the present work, a simple arrangement is made to provide double layer shielding gas supply in addition to primary shielding during gas metal arc welding (GMAW) of two dissimilar stainless steels, i.e., AISI 316 and duplex 2205. Influences of double layer shielding in addition to five more process parameters like welding current, voltage, material of the electrode wire, the type of primary shielding gas, and flow rate on joint tensile strength and fusion zone microhardness are studied. An experimental design technique is used to design the experimental conditions and the results are analyzed to observe the influences of each process parameter and their interactions. The tensile strength is more influenced by the electrode material and the type of shielding, whereas current, interaction between current × voltage and current × flow rate significantly influence microhardness. Welding voltage influences both tensile strength and microhardness. Double layer shielding with CO2 as an outer shielding layer helps in controlling the cooling rate which improves the tensile strength and microhardness. Microstructural observations by scanning electron microscopy reveal that moderate to low heat input with a single layer of shielding results in poor joint strength and severe damage or lack of fusion, and the duplex 2205 filler gives the maximum joint strength due to the presence of a ferrite structure.


  • On Cutter Deflection Profile Errors in End Milling: Modeling and Experimental Validation

    by Anirban Bhattacharya, Tarun Kumar Bera, Ankit Thakur

    In the present paper three dimensional cutter deflections and the corresponding profile errors during end milling are predicted by finite element and bond graph modeling approach. The deflections have been modeled considering the cutter as a cantilever beam fixed at the collet end. Rayleigh beam model is used for modeling to consider the shear force effect, and Castigliano's theorem of strain energy is used to predict the deflections due to radial, tangential, and axial cutting forces. The tool-workpiece contact region is sliced into small elements to apply the forces on the entire contact region and predict deflections more accurately. The predicted deflections at different parametric settings are compared with experimental measurements by measuring the geometric accuracy of the cut profiles. The depth of cut has the most significant influence on profile deviations, while feed and speed have marginal effects. The results reveal that the predictions by finite elements and the bond graph closely matches with the experimental results, and errors of the machined profile are significantly influenced by the radial and tangential deflections. The axial deflection is negligible and leads to insignificant deviation in depth of the cut profile. The proposed model shows that the bond graph simulation takes significantly less computational time and space as compared to the finite element technique.


  • Development of Automatic GMAW Setup for Process Improvements: Experimental and Modeling Approach

    by Anirban Bhattacharya, Tarun Kumar Bera

    Gas metal arc welding (GMAW) offers highly efficient and low-cost welding, but manual movement of torch affects the uniformity of bead geometry, penetration, and heat input. In the present work, an indigenous automatic movement setup is designed and fabricated for GMAW. System behaviors like drive motor response, carriage, and wheel movement are studied through bond graph modeling. Welding time and welding velocity obtained from simulation are used to obtain the deposition efficiency during weld bead deposition on low carbon steel and stainless steel workpieces. Spatter index is also calculated for both the materials. Welding performance of automatic welding is compared with manual movement welding, and automatic welding is found capable to offer high deposition efficiency, low spatter index, uniform depth of penetration, and lower distortion for both the materials. Variation in microhardness and metallurgical observations by scanning electron microscopy are carried out for microstructure analysis.