David Horhota
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
David Horhota has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Michael McVay
Professor, Dept. of Civil and Coastal Engineering, Univ. of Florida, 365 Weil Hall, Gainesville, FL 32611
11 shared publications - Harald Klammler
Universidade Federal da Bahia
4 shared publications - Khiem T. Tran
Department of Civil & Coastal Engineering, University of Florida, Gainesville, USA
3 shared publications - Peter Lai
Assistant State Geotechnical Engineer, Florida Dept. of Transportation, 605 Suwannee St., Tallahassee, FL 32399
3 shared publications Michael Faraone
Assistant Professor, Clarkson University, Department of Civil and Environmental Engineering, P.O. Box 5710, Potsdam, NY 13699-5710
2 shared publications- Michael Rodgers
Engineering School of Sustainable Infrastructure & Environment, University of Florida, Gainesville, FL
2 shared publications
Latest Publications
- 6 December 2023
- Published by Elsevier in Journal of Applied Geophysics
- Vol. 220
Imaging of voids beyond boring depth with 3D SPT-seismic full-waveform tomography
- 6 December 2023
- Published by Elsevier in Journal of Applied Geophysics
- Vol. 220
Imaging of voids beyond boring depth with 3D SPT-seismic full-waveform tomography
- 18 March 2020
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 85 (5) , B169-B179
Sinkhole detection with 3D full seismic waveform tomography
Sinkhole collapse may result in significant property damage and even loss of life. Early detection of sinkhole attributes (buried voids, raveling zones) is critical to limit the cost of remediation. One of the most promising ways to obtain subsurface imaging is 3D seismic full-waveform inversion. For demonstration, a recently developed 3D Gauss-Newton full-waveform inversion (3D GN-FWI) method is used to detect buried voids, raveling soils, and characterize variable subsurface soil/rock layering. It is based on a finite-difference solution of 3D elastic wave equations and Gauss-Newton optimization. The method is tested first on a data set constructed from the numerical simulation of a challenging synthetic model and subsequently on field data collected from two separate test sites in Florida. For the field tests, receivers and sources are placed in uniform 2D surface grids to acquire the seismic wavefields, which then are inverted to extract the 3D subsurface velocity structures. The inverted synthetic results suggest that the approach is viable for detecting voids and characterizing layering. The field seismic results reveal that the 3D waveform analysis identified a known manmade void (plastic culvert), unknown natural voids, raveling, as well as laterally variable soil/rock layering including rock pinnacles. The results are confirmed later by standard penetration tests, including depth to bedrock, two buried voids, and a raveling soil zone. Our study provides insight into the application of the 3D seismic FWI technique as a powerful tool in detecting shallow voids and other localized subsurface features.
- 18 March 2020
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 85 (5) , B169-B179
Sinkhole detection with 3D full seismic waveform tomography
Sinkhole collapse may result in significant property damage and even loss of life. Early detection of sinkhole attributes (buried voids, raveling zones) is critical to limit the cost of remediation. One of the most promising ways to obtain subsurface imaging is 3D seismic full-waveform inversion. For demonstration, a recently developed 3D Gauss-Newton full-waveform inversion (3D GN-FWI) method is used to detect buried voids, raveling soils, and characterize variable subsurface soil/rock layering. It is based on a finite-difference solution of 3D elastic wave equations and Gauss-Newton optimization. The method is tested first on a data set constructed from the numerical simulation of a challenging synthetic model and subsequently on field data collected from two separate test sites in Florida. For the field tests, receivers and sources are placed in uniform 2D surface grids to acquire the seismic wavefields, which then are inverted to extract the 3D subsurface velocity structures. The inverted synthetic results suggest that the approach is viable for detecting voids and characterizing layering. The field seismic results reveal that the 3D waveform analysis identified a known manmade void (plastic culvert), unknown natural voids, raveling, as well as laterally variable soil/rock layering including rock pinnacles. The results are confirmed later by standard penetration tests, including depth to bedrock, two buried voids, and a raveling soil zone. Our study provides insight into the application of the 3D seismic FWI technique as a powerful tool in detecting shallow voids and other localized subsurface features.
- 6 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 613-621
Monitoring While Drilling Shafts in Florida Limestone
The focus of this research is the assessment rock strength in real time during drilled shaft installations. This is achieved through measurements of specific energy which requires five drilling parameters to be continuously monitored and recorded during shaft construction. In a recent investigation conducted by the Florida Department of Transportation, real time measurements of specific energy were used to assess both the quality and length of rock sockets. It was found that the specific energy required to excavate a shaft was directly correlated to the compressive, tensile, and shear strength of the drilled rock. Furthermore, the specific energy obtained from monitoring clearly defined the spatial variability, both horizontally and vertically, within each socketed rock mass. Based on these findings, a new method of estimating shaft capacity was developed in terms of specific energy that can be used as a quality control measure for every drilled shaft installed on a site.
- 6 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 613-621
Monitoring While Drilling Shafts in Florida Limestone
The focus of this research is the assessment rock strength in real time during drilled shaft installations. This is achieved through measurements of specific energy which requires five drilling parameters to be continuously monitored and recorded during shaft construction. In a recent investigation conducted by the Florida Department of Transportation, real time measurements of specific energy were used to assess both the quality and length of rock sockets. It was found that the specific energy required to excavate a shaft was directly correlated to the compressive, tensile, and shear strength of the drilled rock. Furthermore, the specific energy obtained from monitoring clearly defined the spatial variability, both horizontally and vertically, within each socketed rock mass. Based on these findings, a new method of estimating shaft capacity was developed in terms of specific energy that can be used as a quality control measure for every drilled shaft installed on a site.
- 6 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 54-63
Strength and Index Measurements of South Florida Carbonate-Rocks
South Florida has multiple limestone (carbonate-rocks) formations formed during the Pleistocene Epoch near the ground surface. The FDOT is considering their use to support shallow foundations beneath bridge piers or bents. Required for design is assessment of the rocks’ bearing capacity which requires a strength envelope for the rock, as well as identifying their stress-strain response, for identifying failure modes (general, local, and punching). Using Brazilian splitting tension and a Hoek triaxial compression cell (Hoek and Franklin 1968), various confining pressures and volumetric measurements were obtained for multiple rock formations in south Florida. Based on the triaxial measurements, the limestone samples transition from brittle behavior at lower confining pressures (50 kPa or 7 psi) to ductile response at higher confining pressures (1,400 kPa or 200 psi). Also based on triaxial testing, the south Florida formations exhibited volumetric contraction during shear. Influencing the response were several index measurements: dry densities, outer and inner porosities as well as chemical carbonate content of the rock, which are specific to each formation (e.g., Miami, Fort Thompson, Anastasia, and Key Largo).
- 6 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 54-63
Strength and Index Measurements of South Florida Carbonate-Rocks
South Florida has multiple limestone (carbonate-rocks) formations formed during the Pleistocene Epoch near the ground surface. The FDOT is considering their use to support shallow foundations beneath bridge piers or bents. Required for design is assessment of the rocks’ bearing capacity which requires a strength envelope for the rock, as well as identifying their stress-strain response, for identifying failure modes (general, local, and punching). Using Brazilian splitting tension and a Hoek triaxial compression cell (Hoek and Franklin 1968), various confining pressures and volumetric measurements were obtained for multiple rock formations in south Florida. Based on the triaxial measurements, the limestone samples transition from brittle behavior at lower confining pressures (50 kPa or 7 psi) to ductile response at higher confining pressures (1,400 kPa or 200 psi). Also based on triaxial testing, the south Florida formations exhibited volumetric contraction during shear. Influencing the response were several index measurements: dry densities, outer and inner porosities as well as chemical carbonate content of the rock, which are specific to each formation (e.g., Miami, Fort Thompson, Anastasia, and Key Largo).
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144 (3)
Measuring Rock Strength While Drilling Shafts Socketed into Florida Limestone
The focus of this research was the real time assessment of rock strength during drilled shaft installations in Florida. Measures of unconfined compressive strength, a function of rock strength used commonly in shaft design, are provided through five monitored drilling parameters: torque, crowd, rotational speed, penetration rate, and bit diameter. This study is part of a larger project in which laboratory and field investigations were performed. This paper covers the laboratory portion of the investigation in which synthetic limestone blocks were cast at four design strengths representative of Florida limestone and drilled in a controlled environment. The laboratory drillings revealed that torque provides a better correlation with unconfined compressive strength than crowd force, which was found to be the case independent of drilling parameter groupings, and when groupings based on variations in bit diameter and the penetration rate to rotational speed ratio were enforced. During the analysis, multiple drilling equations were investigated, and a unique relationship was developed with Teale’s specific energy equation for nonpercussive rotary drilling using a rock auger.
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144 (3)
Measuring Rock Strength While Drilling Shafts Socketed into Florida Limestone
The focus of this research was the real time assessment of rock strength during drilled shaft installations in Florida. Measures of unconfined compressive strength, a function of rock strength used commonly in shaft design, are provided through five monitored drilling parameters: torque, crowd, rotational speed, penetration rate, and bit diameter. This study is part of a larger project in which laboratory and field investigations were performed. This paper covers the laboratory portion of the investigation in which synthetic limestone blocks were cast at four design strengths representative of Florida limestone and drilled in a controlled environment. The laboratory drillings revealed that torque provides a better correlation with unconfined compressive strength than crowd force, which was found to be the case independent of drilling parameter groupings, and when groupings based on variations in bit diameter and the penetration rate to rotational speed ratio were enforced. During the analysis, multiple drilling equations were investigated, and a unique relationship was developed with Teale’s specific energy equation for nonpercussive rotary drilling using a rock auger.
- 17 March 2015
- Published by American Society of Civil Engineers (ASCE)
- p. 2512-2518
Dual Tip Penetrometer—A New In Situ Approach to Identify Cemented Sand
The dual tip penetrometer (DTP), a novel in situ test, was developed at the University of Florida (UF) to help identify cemented sands. Pairs of DTP and standard cone penetration (CPT) tests were performed at multiple Florida Department of Transportation (FDOT) project sites in Florida. These sites included the West Bay Bridge, and the Port Orange Relief Bridge. Cemented sand layers were present at different depths at these sites. Both DTP and CPT results were analyzed to screen cemented sand identifiers (tip resistance qc, friction ratio Rf, and the ratio between the second and first resistances T2/T1). The ratio T2/T1 was determined to be best identifier for identifying cemented sand. Based on the above test results and analyses, it appears that the DTP could be an efficient tool to identify cemented sand and better predict pile capacity.
- 17 March 2015
- Published by American Society of Civil Engineers (ASCE)
- p. 2512-2518
Dual Tip Penetrometer—A New In Situ Approach to Identify Cemented Sand
The dual tip penetrometer (DTP), a novel in situ test, was developed at the University of Florida (UF) to help identify cemented sands. Pairs of DTP and standard cone penetration (CPT) tests were performed at multiple Florida Department of Transportation (FDOT) project sites in Florida. These sites included the West Bay Bridge, and the Port Orange Relief Bridge. Cemented sand layers were present at different depths at these sites. Both DTP and CPT results were analyzed to screen cemented sand identifiers (tip resistance qc, friction ratio Rf, and the ratio between the second and first resistances T2/T1). The ratio T2/T1 was determined to be best identifier for identifying cemented sand. Based on the above test results and analyses, it appears that the DTP could be an efficient tool to identify cemented sand and better predict pile capacity.
- 24 February 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 2382-2393
Detection of Embedded Anomalies Using 2-D Full Seismic Waveform Tomography
The paper presents an application of 2-D time-domain waveform tomography for detection of embedded voids/anomalies. The measured seismic surface wave fields were inverted using a full waveform inversion (FWI) technique, based on a finite-difference solution of 2-D elastic wave equations and Gauss-Newton inversion method. The key advantage of this approach is the ability to generate all possible wave propagation modes of seismic wavefields (body waves and Rayleigh waves) that are then compared with measured data to infer complex subsurface properties. Both the pressure wave (P-wave) and shear wave (S-wave) velocities are inverted independently and simultaneously for possible indication of soil types. The inversion results of real data show that the waveform analysis was able to delineate a complex profile with an embedded void and highly variable bedrock both laterally and vertically. Independent invasive test (standard penetration test, SPT) was also conducted to verify the seismic test results.
- 24 February 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 2382-2393
Detection of Embedded Anomalies Using 2-D Full Seismic Waveform Tomography
The paper presents an application of 2-D time-domain waveform tomography for detection of embedded voids/anomalies. The measured seismic surface wave fields were inverted using a full waveform inversion (FWI) technique, based on a finite-difference solution of 2-D elastic wave equations and Gauss-Newton inversion method. The key advantage of this approach is the ability to generate all possible wave propagation modes of seismic wavefields (body waves and Rayleigh waves) that are then compared with measured data to infer complex subsurface properties. Both the pressure wave (P-wave) and shear wave (S-wave) velocities are inverted independently and simultaneously for possible indication of soil types. The inversion results of real data show that the waveform analysis was able to delineate a complex profile with an embedded void and highly variable bedrock both laterally and vertically. Independent invasive test (standard penetration test, SPT) was also conducted to verify the seismic test results.
- 1 April 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 25 (4) , 429-437
Study of Laboratory Compaction System Variance Using an Automatic Proctor Calibration Device
This paper describes the development of a portable dynamic energy calibrator (PDEC) for mechanical Proctor compaction machines along with an analysis of system variance on a silty sand’s (A-2-4) dry unit weights. The PDEC measures a rammer’s kinetic energy delivered to the sample and the compressive energy retained in the sample. The monitoring system uses a photoelectric gate and impact force sensor attached to the machine. When the rammer mass is included, the system’s impedance can be calculated. Next, 30 Florida Department of Transportation (FDOT)-approved machines throughout the state were tested, and summary statistics (i.e., mean, standard deviation, and so on) of the kinetic and compressive energies of the machines were found. Scatter plots of hammer kinetic energy along with sample energies allowed for identification of poorly functioning machines (e.g., low-impact energies or variations in mold support). Finally, a series of blind modified compaction tests were performed on A-2-4 soil at six labs at dry and wet of optimum. A regression analysis of the mean and variance of dry unit weight as a function of moisture content, kinetic energy, and sample energy was undertaken. Approximately 50% of the measured dry unit weight variance was associated with variance of kinetic energy, sample energy, or sample moisture. The other 50% of the variance was attributed to operator influence (i.e., sample preparation, lift thicknesses, moisture determination, and so on), which was not measured in this study.
- 1 April 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 25 (4) , 429-437
Study of Laboratory Compaction System Variance Using an Automatic Proctor Calibration Device
This paper describes the development of a portable dynamic energy calibrator (PDEC) for mechanical Proctor compaction machines along with an analysis of system variance on a silty sand’s (A-2-4) dry unit weights. The PDEC measures a rammer’s kinetic energy delivered to the sample and the compressive energy retained in the sample. The monitoring system uses a photoelectric gate and impact force sensor attached to the machine. When the rammer mass is included, the system’s impedance can be calculated. Next, 30 Florida Department of Transportation (FDOT)-approved machines throughout the state were tested, and summary statistics (i.e., mean, standard deviation, and so on) of the kinetic and compressive energies of the machines were found. Scatter plots of hammer kinetic energy along with sample energies allowed for identification of poorly functioning machines (e.g., low-impact energies or variations in mold support). Finally, a series of blind modified compaction tests were performed on A-2-4 soil at six labs at dry and wet of optimum. A regression analysis of the mean and variance of dry unit weight as a function of moisture content, kinetic energy, and sample energy was undertaken. Approximately 50% of the measured dry unit weight variance was associated with variance of kinetic energy, sample energy, or sample moisture. The other 50% of the variance was attributed to operator influence (i.e., sample preparation, lift thicknesses, moisture determination, and so on), which was not measured in this study.
- 4 March 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 617-632
An Approach to Assess LRFD-Φ from Load Test and Borehole Data In and Outside the Footprint of a Drilled Shaft
Currently (2007-2010), AASHTO's LRFD design of deep foundations recommends resistance factors Φ for a variety of scenarios (e.g., method of analysis, number of load tests, etc.). Generally, Φ values account for a desired level of reliability and are based on comprehensive databases (not site specific) of predicted versus measured resistances. Unfortunately, no consideration is given to locations of boreholes with respect to foundation elements, spatial variability of design properties over the site, or the use of load testing on LRFD Φ assessment. The present work considers the case of side friction on axially loaded drilled shafts as assessed from laboratory analysis of rock core samples. Geo-statistical principles are used to rationally account for (1) the presence and amount of site-specific load testing with borehole data in the footprint, (2) the availability of off-site load test data, (3) the amount of site-specific borehole sampling, and (4) the presence or not of borehole data at production shaft locations. In agreement with previous studies, spatial variability within a site is identified as a dominating contributor to overall prediction uncertainty. Additionally, it is shown that spatial variability may only be eliminated by using borings inside shaft footprints and not through additional load testing or collection of borehole data at other locations on a site. A case study with field data is used to illustrate the approach for practice in Florida limestone.
- 4 March 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 617-632
An Approach to Assess LRFD-Φ from Load Test and Borehole Data In and Outside the Footprint of a Drilled Shaft
Currently (2007-2010), AASHTO's LRFD design of deep foundations recommends resistance factors Φ for a variety of scenarios (e.g., method of analysis, number of load tests, etc.). Generally, Φ values account for a desired level of reliability and are based on comprehensive databases (not site specific) of predicted versus measured resistances. Unfortunately, no consideration is given to locations of boreholes with respect to foundation elements, spatial variability of design properties over the site, or the use of load testing on LRFD Φ assessment. The present work considers the case of side friction on axially loaded drilled shafts as assessed from laboratory analysis of rock core samples. Geo-statistical principles are used to rationally account for (1) the presence and amount of site-specific load testing with borehole data in the footprint, (2) the availability of off-site load test data, (3) the amount of site-specific borehole sampling, and (4) the presence or not of borehole data at production shaft locations. In agreement with previous studies, spatial variability within a site is identified as a dominating contributor to overall prediction uncertainty. Additionally, it is shown that spatial variability may only be eliminated by using borings inside shaft footprints and not through additional load testing or collection of borehole data at other locations on a site. A case study with field data is used to illustrate the approach for practice in Florida limestone.
- 1 January 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 139 (1) , 84-94
Influence of Spatially Variable Side Friction and Collocated Data on Single and Multiple Shaft Resistances
Reliability-based design, such as LRFD, aims at meeting desired probability of failure levels for engineered structures. The present work attempts to contribute to this field by analyzing the influence of spatially variable soil/rock strength on the axial resistance uncertainty of single and multiple shafts in group layouts. This includes spatial variability over the individual shaft surfaces, effects of limited data, random measurement errors, and workmanship. A possible correlation between boring data inside or near the footprint of a foundation and the foundation itself is considered. In a geostatistical approach, spatial averaging (upscaling) and a degenerate case of ordinary kriging are applied to develop variance reduction charts and design equations for a series of foundation group layouts (single, double, triple, and quadruple). For the potential situation of an unknown horizontal correlation range at a site, the worst case scenarios are identified and demonstrated in an example problem. R...
- 1 January 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 139 (1) , 84-94
Influence of Spatially Variable Side Friction and Collocated Data on Single and Multiple Shaft Resistances
Reliability-based design, such as LRFD, aims at meeting desired probability of failure levels for engineered structures. The present work attempts to contribute to this field by analyzing the influence of spatially variable soil/rock strength on the axial resistance uncertainty of single and multiple shafts in group layouts. This includes spatial variability over the individual shaft surfaces, effects of limited data, random measurement errors, and workmanship. A possible correlation between boring data inside or near the footprint of a foundation and the foundation itself is considered. In a geostatistical approach, spatial averaging (upscaling) and a degenerate case of ordinary kriging are applied to develop variance reduction charts and design equations for a series of foundation group layouts (single, double, triple, and quadruple). For the potential situation of an unknown horizontal correlation range at a site, the worst case scenarios are identified and demonstrated in an example problem. R...