MMMichael McVay

Michael McVay

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Michael McVay has a total of 45 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Bearing capacity of shallow foundations on Florida limestone: A study of single layer and rock-over-sand subsurface

    by Kunyu Yang, Michael McVay, Thai Nguyen, Kaiqi Wang, Xiaoyu Song, Scott Wasman, Michael Rodgers, David Horhota, Rodrigo Herrera


  • Full-Scale Axial Load Response of Jetted and Grouted Precast Piles in Cohesionless Soils

    by Sudheesh Thiyyakkandi, Michael McVay, C. R. Neeraj

    Jetted and grouted precast piles (JGPPs) are a newly developed urban-friendly deep foundation technique that employs water jetting for pile penetration and pressure grouting to enhance the axial and torsional resistance of precast piles. Previous experimental studies of JGPPs in a large test chamber setup have revealed that they can withstand very high axial loads; however, validation of the same in a typical field scenario was needed. This paper presents the pioneering study of the full-scale axial response of JGPPs in cohesionless soil condition. The study showed that JGPPs exhibit high skin and tip resistances under axial top-down loading. The paper also proposes a direct method to predict the ultimate skin resistance of JGPPs using the pressuremeter test results. The experimental results were compared with the values estimated using both the proposed and existing methods.


  • Operational Limits of Measuring while Drilling in Florida Limestone for Geotechnical Site Characterization

    by Michael B. Rodgers, Michael C. McVay, David J. Horhota, Jose Hernando, Jerry M. Paris

    Rock coring is an essential method of geotechnical site characterization for foundations supported by rock, in which three possible phases of operation exist: inefficient, optimized, and destructive. When operating within the optimized phase, core recoveries and the rock quality designation reflect the strata encountered. However, the optimized phase is rarely achieved in practice, leading to deficiencies in strength assessment and geotechnical site characterization. This paper identifies the operational limits that separate each phase of rock coring by using measuring while drilling (MWD) and quantifies the increased energy that results from an inadequate depth of cut (Phase 1), the effects of breaking rock particles into smaller sizes, and the damage that occurs to core specimens from increased frictional resistance (Phase 3), as well as the effect rock strength and bit geometry have on mechanical efficiency. Drilling parameter interdependencies are discussed and detailed guidelines to assess rock strength in situ via MWD are provided. Finally, recommended coring guidelines are established through MWD which optimize the quantity and quality of strength assessments collected to improve geotechnical site characterization.


  • Sinkhole detection with 3D full seismic waveform tomography

    by Majid Mirzanejad, Khiem T. Tran, Michael McVay, David Horhota, Scott J. Wasman

    Sinkhole collapse may result in significant property damage and even loss of life. Early detection of sinkhole attributes (buried voids, raveling zones) is critical to limit the cost of remediation. One of the most promising ways to obtain subsurface imaging is 3D seismic full-waveform inversion. For demonstration, a recently developed 3D Gauss-Newton full-waveform inversion (3D GN-FWI) method is used to detect buried voids, raveling soils, and characterize variable subsurface soil/rock layering. It is based on a finite-difference solution of 3D elastic wave equations and Gauss-Newton optimization. The method is tested first on a data set constructed from the numerical simulation of a challenging synthetic model and subsequently on field data collected from two separate test sites in Florida. For the field tests, receivers and sources are placed in uniform 2D surface grids to acquire the seismic wavefields, which then are inverted to extract the 3D subsurface velocity structures. The inverted synthetic results suggest that the approach is viable for detecting voids and characterizing layering. The field seismic results reveal that the 3D waveform analysis identified a known manmade void (plastic culvert), unknown natural voids, raveling, as well as laterally variable soil/rock layering including rock pinnacles. The results are confirmed later by standard penetration tests, including depth to bedrock, two buried voids, and a raveling soil zone. Our study provides insight into the application of the 3D seismic FWI technique as a powerful tool in detecting shallow voids and other localized subsurface features.


  • Monitoring While Drilling Shafts in Florida Limestone

    by Michael B. Rodgers, Michael C. McVay, David J. Horhota

    The focus of this research is the assessment rock strength in real time during drilled shaft installations. This is achieved through measurements of specific energy which requires five drilling parameters to be continuously monitored and recorded during shaft construction. In a recent investigation conducted by the Florida Department of Transportation, real time measurements of specific energy were used to assess both the quality and length of rock sockets. It was found that the specific energy required to excavate a shaft was directly correlated to the compressive, tensile, and shear strength of the drilled rock. Furthermore, the specific energy obtained from monitoring clearly defined the spatial variability, both horizontally and vertically, within each socketed rock mass. Based on these findings, a new method of estimating shaft capacity was developed in terms of specific energy that can be used as a quality control measure for every drilled shaft installed on a site.


  • Measuring Rock Strength While Drilling Shafts Socketed into Florida Limestone

    by Michael Rodgers, Michael McVay, Christopher Ferraro, David Horhota, Caitlin Tibbetts, Stephen Crawford

    The focus of this research was the real time assessment of rock strength during drilled shaft installations in Florida. Measures of unconfined compressive strength, a function of rock strength used commonly in shaft design, are provided through five monitored drilling parameters: torque, crowd, rotational speed, penetration rate, and bit diameter. This study is part of a larger project in which laboratory and field investigations were performed. This paper covers the laboratory portion of the investigation in which synthetic limestone blocks were cast at four design strengths representative of Florida limestone and drilled in a controlled environment. The laboratory drillings revealed that torque provides a better correlation with unconfined compressive strength than crowd force, which was found to be the case independent of drilling parameter groupings, and when groupings based on variations in bit diameter and the penetration rate to rotational speed ratio were enforced. During the analysis, multiple drilling equations were investigated, and a unique relationship was developed with Teale’s specific energy equation for nonpercussive rotary drilling using a rock auger.


  • Field Measurement of Noise and Ground Surface Vibration during Pile Jetting and Grouting

    by Sudheesh Thiyyakkandi, Michael C. McVay, Peter Lai, Rodrigo Herrera

    Noise and vibration are critical issues associated with pile driving operations in an urban environment. Alternative foundations such as drilled shafts and augercast piles alleviate much of the operational noise and vibration. However, the cast-in place installation process may raise concerns in quality control if not adequately monitored. Post grouting the drilled shaft base has been widely used to mobilize a larger portion of the tip resistance prior to construction of the superstructure, thereby controlling the axial displacement during the service. In response to the operational challenges in urban environments, the Florida Department of Transportation and the University of Florida have recently developed a new generation of deep foundation, namely “jetted and grouted precast pile”. The process consists of pressurized water jetting a concrete pile instead of a hammer-driven installation, and subsequent side and tip grouting the pile, which significantly improve skin and tip resistance, respectively, as well as lateral and torsional stiffness. Several studies have been focused on such increase in axial and torsional resistance by grouting techniques. However, there has been little field data available to support quantifiable noise and vibration reduction by jetting and grouting processes. This paper presents field measurements of noise and ground surface vibration during full-scale installation of jetted and grouted piles. Comparison of measured data to recommended noise and vibration limits suggests that jetting and grouting techniques are a viable solution for urban geo-infrastructure development.


  • Evaluation of Drilled Shaft Capacity Using Embedded Sensors and Statnamic Testing

    by Khiem T. Tran, Michael McVay, Trung Dung Nguyen, Scott J. Wasman

    This paper presents an application of the embedded data collector (EDC) approach using strain and acceleration measurements at the top and bottom of a pile (drilled shaft) during dynamic loading (Statnamic) for estimation of static side and tip resistance. For assessment of the skin friction, wave propagation along the pile was modeled as a one-dimensional (1D) wave equation with nonlinear static skin friction and viscous damping. The soil–pile system was divided into segments, and each segment was characterized with independent multilinear skin friction. The skin friction of each segment was determined by least-squares fitting of computed particle velocities to the measured data at the top and bottom of the pile. For assessment of the tip resistance, the pile tip was modeled as a single—degree-of-freedom nonlinear system. A nonlinear stiffness–displacement relationship was determined by balancing force and energy from inertia, damping, and stiffness against the measured tip data. The technique wa...


  • Evaluation of Unknown Foundations Using Surface-Based Full Waveform Tomography

    by Trung Dung Nguyen, Khiem T. Tran, Michael McVay

    An application of two-dimensional (2D) time-domain full waveform tomography is presented to evaluate existing foundations using surface-based seismic wave fields. The full waveform inversion (FWI) technique is based on a finite-difference solution of 2D elastic wave equations and the Gauss–Newton inversion method. Both compression-wave (P-wave) and shear-wave (S-wave) velocities are inverted independently and simultaneously to increase the credibility of characterized profiles. The FWI technique was applied on both synthetic and real experimental data sets. Inverted results of synthetic data revealed that individual embedded foundation elements (piles) and soil between piles were distinguished. For real experimental data, seismic surface wave fields were measured next to two drilled shafts with a 1.2-m diameter and a 15-m length and then inverted by the FWI technique. The waveform analysis successfully profiled embedded shaft elements and subsurface soil stratigraphy, and shaft lengths of 15 m we...