KSKenneth H. Stokoe

Kenneth H. Stokoe

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kenneth H. Stokoe has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    NHERI@UTexas experimental facility with large-scale mobile shakers for field studies: a decade of discovery in natural hazards engineering

    by Kenneth H. Stokoe, Sungmoon Hwang, Brady R. Cox, Patricia M. Clayton, Robert B. Gilbert

    Introduction: Natural hazards present significant risks to infrastructure and communities, emphasizing the importance of advanced tools and methods to better understand and mitigate these challenges. The Natural Hazards Engineering Research Infrastructure (NHERI) experimental facility at the University of Texas (NHERI@UTexas), funded by the National Science Foundation (NSF), addresses this need by offering unique resources for large-scale field testing.Methods: NHERI@UTexas contributes unique, large-scale, literally one-of-a-kind, mobile dynamic shakers and associated instrumentation to investigate seismic, cyclic, and static in-situ testing. These capabilities allow researchers to conduct experiments on actual infrastructure and geotechnical systems under real-world conditions, often impossible to accurately simulate in the laboratory.Results: NHERI@UTexas has supported pioneering research in several areas, including: (1) enhanced 2D/3D geotechnical and seismic subsurface imaging, (2) in-situ characterization of liquefaction resistance and nonlinear dynamic soil behavior, (3) development of in-situ nondestructive soil-foundation-structure interaction (SFSI) methods, and (4) rapid geotechnical assessments following natural hazard events. These efforts have advanced the validation and calibration of numerical model and methodologies using full-scale experimental data.Discussion: NHERI@UTexas enable researchers to gain new insights and drive innovations in advancing resilient and sustainable solutions for natural hazards problems.


  • Open Access

    NHERI@UTexas Experimental Facility With Large-Scale Mobile Shakers for Field Studies

    by Kenneth H. Stokoe, Brady R. Cox, Patricia M. Clayton, Farnyuh Menq

    The Natural Hazards Engineering Research Infrastructure (NHERI) experimental facility at the University of Texas (NHERI@UTexas) is funded by the National Science Foundation (NSF). NHERI@UTexas contributes unique, large-scale, hydraulically controllable mobile shakers and associated instrumentation to study and develop novel, in-situ testing methods that can be used to evaluate the needs of existing infrastructure as well as optimize the design of future infrastructure. The ability to test existing infrastructure under actual field conditions bridges the gap in the transformative tools needed for the next frontier of resilient and sustainable natural-hazards research. Further, these unique facilities are available to any NSF-funded research. The field shakers and support equipment are described. Examples of on-going and future projects in three key areas of investigation that NHERI@UTexas is targeting are presented. These examples includes: (1) performing more accurate 2D/3D subsurface geotechnical imaging up larger depths, (2) characterizing liquefaction resistance and non-linear dynamic behavior in situ soils, and (3) developing in-situ methods non-destructive soil-foundation-structure interaction (SFSI) studies.


  • Open Access

    Enhanced Sensing and Data Processing System for Continuous Profiling of Pavement Deflection

    by Boo Hyun Nam, Kenneth H. Stokoe, Heejung Youn

    Continuous pavement deflection profiling in a nondestructive manner has received great attention because of its efficiency in pavement evaluation. The Rolling Dynamic Deflectometer (RDD) is a continuous pavement deflection profiling technology and has demonstrated its successful use at many pavement projects. However, RDD’s current test speed of 1.6 km/h (with the prototype rolling sensor) often limits its use in large-coverage projects and traffic congested areas. Increasing the test speed creates a higher-noise environment, lowered signal-to-noise ratio, and sensor decoupling with the ground surface. This study presents the enhancement to the RDD for increased test speed, associated with the new design of the lower-level rolling sensor and higher-performance digital filter and data processing. The new sensor along with the enhanced data processing could increase the spatial resolution of the deflection data, which allows the increase of the test speed of the RDD.


  • Advanced Data Analysis of Downhole Seismic Records

    by Sungmoon Hwang, Farnyuh Menq, Kenneth H. Stokoe, Richard C. Lee, Julia N. Roberts

    Downhole seismic testing is commonly used to determine constrained compressional wave and shear wave velocity profiles in geotechnical earthquake engineering investigations. Wave velocities are calculated based on arrival times selected from the original or filtered time records. However, selecting the arrival times can be subjective for reasons such as signal clarity, mechanical and electrical interferences, and significant attenuation with depth. These factors can create inconsistencies in arrival time selections which may result in disputes between the original analyzers and reviewers. In this study, the use of the integrated continuous wavelet transform (ICWT) method is investigated for use in analyzing downhole seismic records. Results using the ICWT method are compared with those obtained from conventional visual “picks”. The ICWT method applies continuous wavelet transform to interpret direct arrival measurements. The key feature of the method is transferring a nonlinear sinusoidal-like signal to a linear phase angle plot. Peaks in the recorded signal are shown as 0°, and troughs are shown as phase angle of 180°. By selecting the time point of 0- or 180-degrees with an amplitude above a selected threshold value, the arrival time of first peaks or troughs can be uniquely identified.


  • Measured and Predicted V S Values of a Granular Backfill Test Pad

    by Kenneth H. Stokoe, Sungmoon Hwang, Michael Boone, Michael R. Lewis, Yaning Wang, Matthew F. Cooke, Andrew Keene

    A backfill test pad of sand to silty sand was constructed to evaluate the stress-dependent properties of the backfill material. The test pad was about 6.1 m thick and was constructed to assess the potential of using on-site granular soils as Category-1 compacted backfill for a potential nuclear-power reactor site. During construction, compaction testing and surface-wave seismic (SASW) testing were performed at backfill thicknesses of about 2.1, 4.3, and 6.1 m. Additional testing of the completed test pad included borings, standard penetration tests, seismic piezocone penetration tests, and crosshole and downhole seismic tests. The in situ testing was complimented with laboratory testing, including modified Proctor compaction tests and resonant column testing. The focus in this paper is on the in situ, small-strain shear wave velocities (VS) and comparisons between: (1) different field seismic methods, (2) field and laboratory measurements, and (3) predictions from correlations based on empirical equations and penetration resistances.


  • Utilizing Direct-Push Crosshole Seismic Testing to Verify the Effectiveness of Shallow Ground Improvements: A Case Study Involving Low-Mobility Grout Columns in Christchurch, New Zealand

    by Sungmoon Hwang, Julia N. Roberts, Kenneth H. Stokoe, Brady R. Cox, Sjoerd van Ballegooy, Chris Soutar

    A full-scale field testing program was conducted in Christchurch, New Zealand, to assess the effectiveness of soil stiffening and/or densification caused by the installation of shallow, low-mobility grout (LMG) columns. The LMG columns were designed to be 4 m long and were installed at three different test areas for the purpose of liquefaction mitigation in loose silty sands. Direct-push crosshole (DPCH) seismic testing was performed on unimproved ground and on ground that was improved with the LMG columns. The purpose of the DPCH testing was to verify the integrity of the LMG columns and to identify any changes in soil stiffness created by their installation. The crosshole testing involved sampling the unimproved and improved ground conditions with horizontally propagating shear waves at depths ranging from 0.4 to 5.0 m in 0.2-m increments. The seismic verification method clearly delineated zones of change and LMG column variability. The verification results were confirmed by post-characterization trenching.


  • In Situ and Laboratory Measured Dynamic Properties of a Marine Clay

    by Albert R. Kottke, Andrew Keene, Yaning Wang, Boonam Shin, Kenneth H. Stokoe, Michael R. Lewis

    Combined resonant-column/torsional-shear tests were performed on four specimens of marine clay collected at varying depths over a range of confining pressures commensurate with the specimen depths. Using the small-strain measurements from these tests, the influences of stress state and void ratio on the small-strain shear stiffness, shear-wave velocity, and material damping ratio were studied. As the confining pressure increases and the specimen consolidates, both the shear stiffness and velocity increase. The rate of this increase follows typical trends of consolidation curves: less sensitive during recompression and unloading, and more sensitive during virgin compression. The laboratory-measured Vs showed good agreement with the field values with little evidence of sample disturbance. The influence of stress on Gmax and Vs was also found to be in good agreement with the laboratory. The relationship between the stress state, void ratio, and material damping is more complicated and does not show as consistent a behavior.


  • Building a Framework for Predicting Foundation Settlements on Granular Soil with Dynamically Measured Properties

    by Onur Kacar, Ii Kenneth H. Stokoe, Kwangsoo Park

    Settlements are usually the primary concern in designing shallow foundations on freely draining granular soil. Settlement predictions are traditionally based on empirical correlations with in-situ penetration tests due to difficulties in obtaining undisturbed samples. In the proposed framework, field measurements of shear wave velocity (Vs) are used to characterize the in-situ condition in terms of small-strain shear modulus (Gmax) profiles. Disturbed field samples are recovered to determine gradation characteristics. Normalized shear modulus-shear strain relationships (G/Gmax-log γ) that have been developed from dynamic resonant column testing of reconstituted sands and gravels are used to model stress state, strain amplitude, and material dependencies. The G/Gmax-log γ relationships are modified to extend to strains of several percent. A subroutine has been implemented in the finite element program PLAXIS to combine the field Gmax profiles, modified G/Gmax-log γ relationships, and gradation characteristics to estimate stress-strain response under loading. The usefulness of the approach is demonstrated by comparing predicted and measured load-settlement curves from field tests with 0.46 and 0.91 m diameter footings. Nonlinearity and settlement values are predicted well at loads in the working stress range.


  • Analyst J: Analysis of the UTexas 1 Surface Wave Dataset Using the SASW Methodology

    by Y.-C. Lin, S.-H. Joh, K. H. Stokoe

    The UTexas 1 surface wave dataset was collected at a site in Christchurch, New Zealand. The dataset contains active-source, linear-array data and ambient wavefield, circular-array data. Only the active-source data were analyzed using the spectral-analysis-of-surface-waves (SASW) methodology. The dispersion and forward modeling procedures are documented in the paper. Forward modeling was performed using both the 3-D global and 3-D array-based procedures. A well-constrained Vs profile was determined to a depth of about 140 m. In forward modeling, effective-mode transitions were identified in the dataset. As such, the correct Vs profile could not be determined if it were assumed that the field data represented only the fundamental mode.


  • A Multi-Purpose Pavement Testing Device: Applications of the Rolling Dynamic Deflectometer and the Stationary Dynamic Deflectometer in Pavements

    by B. H. Nam, K. H. Stokoe, M. Won, J. A. Bay

    The rolling dynamic deflectometer (RDD) capable of measuring continuous deflection profiles along pavements has been used in (a) delineating problematic areas to be repaired, (b) identifying potential locations for reflective cracking, and (c) developing inputs for selecting a rehabilitation scheme. Unlike discrete testing methods, the RDD travels along a pavement and its continuous deflection profile provides 100% coverage along the pavement. However, the use of the RDD in a stationary mode, called the stationary dynamic deflectometer (SDD), is used for super-accelerated pavement testing (SAP). SAP testing is defined as the application of one million load repetitions to a full-scale pavement system in one day and evaluates the fatigue performance of in-situ pavements. The SDD applications include (a) evaluating rut resistance in a flexible pavement and fatigue-crack resistance in a rigid pavement and (b) estimating the remaining life of in-service pavements under heavy traffic loads. This paper introduces benefits of the RDD as a multipurpose pavement testing device and presents three case studies using the RDD and SDD.