Abdolreza Osouli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Abdolreza Osouli has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Youssef M. A. Hashash
Department of Civil & Environmental Engineering University of Illinois at Urbana‐Champaign Urbana Illinois USA
3 shared publications - Camilo Marulanda
INGETEC
2 shared publications - Hwayeon Song
Graduate, Research Assistants, Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 205 N. Mathews Ave., Urbana, IL 61801
2 shared publications - Ali Pak
Department of Civil Engineering, Sharif University of Technology, Tehran, Iran
1 shared publication - Jamshid Ghaboussi
Dept. of Civil Engineering, University of Akron, Akron, OH, 44325
1 shared publication - L. Y. Liu
Associate Professor, University of Illinois at Urbana-Champaign, Urbana, IL 61801
1 shared publication
Latest Publications
- 1 September 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 134 (9) , 1399-1406
Central Artery/Tunnel Project Excavation Induced Ground Deformations
Estimate of deformations around urban excavations is a primary concern for designers, contractors, owners, and potentially affected third parties. Significant efforts have gone into the development of empirically based methods to estimate deformations relying on a large number of case histories. The construction of the deep excavations for the central artery/tunnel project provides valuable information on observed deformations due to the construction of these excavations. Lateral deformations and surface settlements for three construction contracts are collected and summarized in a form similar to published empirical charts. The stiff support system used in these braced excavation and the embedment of the wall into stiff strata control deformations to minimal levels. The data show that surface settlements, although small, extend farther away from the excavation than previously reported.
- 1 September 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 134 (9) , 1399-1406
Central Artery/Tunnel Project Excavation Induced Ground Deformations
Estimate of deformations around urban excavations is a primary concern for designers, contractors, owners, and potentially affected third parties. Significant efforts have gone into the development of empirically based methods to estimate deformations relying on a large number of case histories. The construction of the deep excavations for the central artery/tunnel project provides valuable information on observed deformations due to the construction of these excavations. Lateral deformations and surface settlements for three construction contracts are collected and summarized in a form similar to published empirical charts. The stiff support system used in these braced excavation and the embedment of the wall into stiff strata control deformations to minimal levels. The data show that surface settlements, although small, extend farther away from the excavation than previously reported.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 605-612
Effects of Solar Energy on the Mechanical Properties of Tailings in Tailings Dams
Mine tailings are the most common materials that are used in construction of tailings dams. Due to high level of environmental hazard and serious consequences that are associated with tailings dam failure, proper design of tailings dams is an important factor in mining industry. Water level fluctuation, change in permeability of dam foundation, seismic loads, and excessive settlements are the most common reasons of failure, particularly in upstream type tailings dams. Due to low shear strength of wet tailings, drying of tailing material is very common in practice during the dam construction. In hot climate, the received solar energy at the soil surface converts to soil heat flux, air heat flux, and evaporation energy. The evaporation energy generates matric suction in the tailings fabric which can potentially induce apparent cohesion and consequently improve the shear strength of tailing materials. The soil-water characteristic curve is used to correlate the volumetric water content of the soil with matric suction. In this study, an algorithm is proposed to determine the amount of apparent cohesion, induced by sunlight effects on the stability of tailing dams. The proposed algorithm is employed in stability analysis of Barnick Mercur tailings dam, which is a 280 foot high dam in a gold mine in Utah. The obtained results indicate that taking advantage of solar energy to enhance the geomechanical properties of tailing materials can improve the stability of tailings dam.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 605-612
Effects of Solar Energy on the Mechanical Properties of Tailings in Tailings Dams
Mine tailings are the most common materials that are used in construction of tailings dams. Due to high level of environmental hazard and serious consequences that are associated with tailings dam failure, proper design of tailings dams is an important factor in mining industry. Water level fluctuation, change in permeability of dam foundation, seismic loads, and excessive settlements are the most common reasons of failure, particularly in upstream type tailings dams. Due to low shear strength of wet tailings, drying of tailing material is very common in practice during the dam construction. In hot climate, the received solar energy at the soil surface converts to soil heat flux, air heat flux, and evaporation energy. The evaporation energy generates matric suction in the tailings fabric which can potentially induce apparent cohesion and consequently improve the shear strength of tailing materials. The soil-water characteristic curve is used to correlate the volumetric water content of the soil with matric suction. In this study, an algorithm is proposed to determine the amount of apparent cohesion, induced by sunlight effects on the stability of tailing dams. The proposed algorithm is employed in stability analysis of Barnick Mercur tailings dam, which is a 280 foot high dam in a gold mine in Utah. The obtained results indicate that taking advantage of solar energy to enhance the geomechanical properties of tailing materials can improve the stability of tailings dam.
- 21 September 2007
- Published by American Society of Civil Engineers (ASCE)
Soil Behavior and Excavation Instrumentation Layout
During the construction of urban excavations, instruments are installed to monitor ground response to various construction activities, to verify design assumptions and to effectively apply the observational approach. Data collected from these instruments are also used in inverse analyses to develop improved soil models suitable for representing soil response during excavation. This study examines the relationship between various instruments typically used on an excavation project and the quality of information that can be extracted for excavation modeling. A synthetically generated set of instrument measurements using an idealized soil profile are used. Instrument readings considered include inclinometers placed in the support wall and in the retained soil, surface settlement points, extensometers, heave gages, piezometers and strain gauges in the bracing system. Various combinations of measurements are used in a novel inverse analysis approach, SelfSim, to extract the soil behavior. The study shows that in addition to the measurements of lateral wall deflections and surface settlement, measured forces in the struts significantly improve the quality of the extracted soil behavior and the overall predictive capability of the model. Inclinometers placed some distance behind the wall also improve the predictive quality of the model especially small strain soil non-linearity and provide some redundancy to measured settlements.
- 21 September 2007
- Published by American Society of Civil Engineers (ASCE)
Soil Behavior and Excavation Instrumentation Layout
During the construction of urban excavations, instruments are installed to monitor ground response to various construction activities, to verify design assumptions and to effectively apply the observational approach. Data collected from these instruments are also used in inverse analyses to develop improved soil models suitable for representing soil response during excavation. This study examines the relationship between various instruments typically used on an excavation project and the quality of information that can be extracted for excavation modeling. A synthetically generated set of instrument measurements using an idealized soil profile are used. Instrument readings considered include inclinometers placed in the support wall and in the retained soil, surface settlement points, extensometers, heave gages, piezometers and strain gauges in the bracing system. Various combinations of measurements are used in a novel inverse analysis approach, SelfSim, to extract the soil behavior. The study shows that in addition to the measurements of lateral wall deflections and surface settlement, measured forces in the struts significantly improve the quality of the extracted soil behavior and the overall predictive capability of the model. Inclinometers placed some distance behind the wall also improve the predictive quality of the model especially small strain soil non-linearity and provide some redundancy to measured settlements.
- 15 May 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 336-341
New Technologies for Tracking Urban Excavation Progress and Estimating Deformations
This paper describes novel developments of tools for predicting, monitoring, and controlling ground movements associated with excavations in urban areas. The paper describes developments in the following areas (1) Laser scanning for developing an accurate record of construction activities, (2) Intelligent, self-updating numerical models to compute anticipated ground movements, and to learn from field observations, and (3) integration of heterogeneous data using a GIS based system. These new technologies are illustrated using excavations in the Chicago area.
- 15 May 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 336-341
New Technologies for Tracking Urban Excavation Progress and Estimating Deformations
This paper describes novel developments of tools for predicting, monitoring, and controlling ground movements associated with excavations in urban areas. The paper describes developments in the following areas (1) Laser scanning for developing an accurate record of construction activities, (2) Intelligent, self-updating numerical models to compute anticipated ground movements, and to learn from field observations, and (3) integration of heterogeneous data using a GIS based system. These new technologies are illustrated using excavations in the Chicago area.