Michael C. Halbig
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Michael C. Halbig has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Mrityunjay Singh
Ohio Aerospace Institute, Cleveland, OH 44142, USA
10 shared publications - Meelad Ranaiefar
NASA Glenn Research Center, Cleveland, OH 44135, USA
5 shared publications Mrityunjay Singh
Ohio Aerospace Institute 44142 Cleveland OH USA
5 shared publications- Yi Zheng
Department of Mechanical and Industrial Engineering, Northeastern University, Boston, MA 02115, USA
4 shared publications - Amjad S. Almansour
NASA Glenn Research Center, Cleveland, OH 44135, USA
3 shared publications - Jonathan A. Salem
NASA Glenn Research Center, Cleveland, OH 44135, USA
3 shared publications
Latest Publications
- Open Access
- 5 September 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (9) , 478
Influence of Processing Parameters on the Mechanical Properties of 3D Printed Borosilicate Particulate Reinforced Polymer Composites
Emerging composite materials are expanding the potential of additive manufacturing and enabling applications previously restricted by traditional manufacturing methods through their multi-phase nature and complex internal geometry. Additionally, these materials can be pyrolyzed to create dense metal, ceramic, and glass parts with geometries typically not achievable by traditional processes. Additive manufacturing of borosilicate glass composites can enable new applications in nuclear engineering, astronomy, and bone regrowth therapy. To elucidate the process–parameter relationship of borosilicate–polylactic acid (PLA) composites, mechanical test specimens were fabricated by fused-filament fabrication and compared with a pure PLA baseline. Optical and scanning electron microscopy were conducted to observe the specimen microstructure before and after testing. From the stress–strain curves, the highest compressive yield strength for the composite was 28.22 MPa, and the highest compressive yield strength for PLA was 49.30 MPa. Print orientation was found to benefit the composite material but have a detrimental effect on the pure matrix material. Borosilicate–PLA with 100% infill, 1 shell wall, and layer lines parallel to compression axis had an elastic modulus of 2.66 GPa. Microscopy revealed that lower-modulus composite specimens had the particulates re-distributed within the matrix. Tensile testing was done according to a polymer testing standard, which caused difficulties obtaining consistent fracture within the gauge length.
- 5 September 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (9) , 478
Open AccessInfluence of Processing Parameters on the Mechanical Properties of 3D Printed Borosilicate Particulate Reinforced Polymer Composites
Emerging composite materials are expanding the potential of additive manufacturing and enabling applications previously restricted by traditional manufacturing methods through their multi-phase nature and complex internal geometry. Additionally, these materials can be pyrolyzed to create dense metal, ceramic, and glass parts with geometries typically not achievable by traditional processes. Additive manufacturing of borosilicate glass composites can enable new applications in nuclear engineering, astronomy, and bone regrowth therapy. To elucidate the process–parameter relationship of borosilicate–polylactic acid (PLA) composites, mechanical test specimens were fabricated by fused-filament fabrication and compared with a pure PLA baseline. Optical and scanning electron microscopy were conducted to observe the specimen microstructure before and after testing. From the stress–strain curves, the highest compressive yield strength for the composite was 28.22 MPa, and the highest compressive yield strength for PLA was 49.30 MPa. Print orientation was found to benefit the composite material but have a detrimental effect on the pure matrix material. Borosilicate–PLA with 100% infill, 1 shell wall, and layer lines parallel to compression axis had an elastic modulus of 2.66 GPa. Microscopy revealed that lower-modulus composite specimens had the particulates re-distributed within the matrix. Tensile testing was done according to a polymer testing standard, which caused difficulties obtaining consistent fracture within the gauge length.
- Open Access
Geometry-Regulated Thermal Performance of Sedimentation-Stable MicroPCM Composite Capsules for Battery Thermal Management Systems Fabricated via 3D Printing
Thermal management is critical for maintaining the safety and performance of lithium-ion batteries. Phase change materials (PCMs) have been widely studied as passive cooling media due to their high latent heat capacity, but major technical challenges remain due to their relatively low thermal conductivity and nanoparticle sedimentation in composite systems. In this work, a composite phase change material (PCM) consisting of paraffin wax, a microencapsulated phase change material (MicroPCM 28D), and nano carbon black is developed to enhance thermal stability and suppress particle sedimentation through increased viscosity of the PCM matrix. Five capsule geometries fabricated by fused filament fabrication (FFF) 3D printing are experimentally investigated under airflow velocities ranging from 0 to 10 m s−1. Wind tunnel experiments with infrared thermography are used to evaluate the thermal response of the PCM capsules. The results show that airflow velocity and capsule geometry strongly influence heat dissipation behavior. Compared with conventional wax composites, the MicroPCM 28D composite capsules reduce peak temperature by approximately 2–4 °C under airflow velocities of 0–10 m/s. These findings provide insights into geometry-regulated convection and stable composite PCM design for lithium-ion battery thermal management systems.
Open AccessGeometry-Regulated Thermal Performance of Sedimentation-Stable MicroPCM Composite Capsules for Battery Thermal Management Systems Fabricated via 3D Printing
Thermal management is critical for maintaining the safety and performance of lithium-ion batteries. Phase change materials (PCMs) have been widely studied as passive cooling media due to their high latent heat capacity, but major technical challenges remain due to their relatively low thermal conductivity and nanoparticle sedimentation in composite systems. In this work, a composite phase change material (PCM) consisting of paraffin wax, a microencapsulated phase change material (MicroPCM 28D), and nano carbon black is developed to enhance thermal stability and suppress particle sedimentation through increased viscosity of the PCM matrix. Five capsule geometries fabricated by fused filament fabrication (FFF) 3D printing are experimentally investigated under airflow velocities ranging from 0 to 10 m s−1. Wind tunnel experiments with infrared thermography are used to evaluate the thermal response of the PCM capsules. The results show that airflow velocity and capsule geometry strongly influence heat dissipation behavior. Compared with conventional wax composites, the MicroPCM 28D composite capsules reduce peak temperature by approximately 2–4 °C under airflow velocities of 0–10 m/s. These findings provide insights into geometry-regulated convection and stable composite PCM design for lithium-ion battery thermal management systems.
- Open Access
Design of Experiments Methodology for Fused Filament Fabrication of Silicon-Carbide-Particulate-Reinforced Polylactic Acid Composites
Fused Filament Fabrication (FFF) is an additive manufacturing technique that constructs parts by extruding material layer by layer. It offers advantages such as rapid prototyping, cost-effectiveness, and the ability to produce complex geometries. This study investigates the mechanical behavior of a composite filament composed of silicon carbide (SiC) ceramic particulates embedded in a polylactic acid (PLA) matrix, fabricated via FFF. Pure PLA specimens were also printed and tested to serve as a baseline. A Design of Experiments (DOE) methodology was employed to evaluate the influence of key printing parameters on mechanical properties, including Young’s modulus, yield strength, and ultimate strength. Microstructural analysis was performed on printed specimens using scanning electron microscopy (SEM). For compression testing, the parameters studied were infill percentage, number of shells, and print orientation. For tensile testing, the parameters included layer height, number of shells, and infill angle. Results indicated that infill percentage had the most significant impact on compressive properties, while layer height was the dominant factor in tensile performance. These findings provide insights into optimizing FFF process parameters for ceramic-particulate-reinforced polymer composites.
Open AccessDesign of Experiments Methodology for Fused Filament Fabrication of Silicon-Carbide-Particulate-Reinforced Polylactic Acid Composites
Fused Filament Fabrication (FFF) is an additive manufacturing technique that constructs parts by extruding material layer by layer. It offers advantages such as rapid prototyping, cost-effectiveness, and the ability to produce complex geometries. This study investigates the mechanical behavior of a composite filament composed of silicon carbide (SiC) ceramic particulates embedded in a polylactic acid (PLA) matrix, fabricated via FFF. Pure PLA specimens were also printed and tested to serve as a baseline. A Design of Experiments (DOE) methodology was employed to evaluate the influence of key printing parameters on mechanical properties, including Young’s modulus, yield strength, and ultimate strength. Microstructural analysis was performed on printed specimens using scanning electron microscopy (SEM). For compression testing, the parameters studied were infill percentage, number of shells, and print orientation. For tensile testing, the parameters included layer height, number of shells, and infill angle. Results indicated that infill percentage had the most significant impact on compressive properties, while layer height was the dominant factor in tensile performance. These findings provide insights into optimizing FFF process parameters for ceramic-particulate-reinforced polymer composites.
- Open Access
Effect of Processing Parameters on the Mechanical Behavior of 3D-Printed Basalt Moon Dust Reinforced Polylactic Acid Composites
Advanced composite materials and manufacturing technologies are critical to sustain human presence in space. Mechanical testing and analysis are needed to elucidate the effect of processing parameters on composites’ material properties. In this study, test specimens are 3D printed via a fused-filament fabrication (FFF) approach from a basalt moon dust-polylactic acid (BMD-PLA) composite filament and from pure PLA filament. Compression and tensile testing were conducted to determine the yield strength, ultimate strength, and Young’s modulus of specimens fabricated under several processing conditions. The maximum compressive yield strength for the BMD-reinforced samples is 27.68 MPa with print parameters of 100% infill, one shell, and 90° print orientation. The maximum compressive yield strength for the PLA samples is 63.05 MPa with print parameters of 100% infill, three shells, and 0° print orientation. The composite samples exhibit an increase in strength when layer lines are aligned with loading axis, whereas the PLA samples decreased in strength. This indicates a fundamental difference in how the composite behaves in comparison to the pure matrix material. In tension, test specimens have unpredictable failure modes and often broke outside the gauge length. A portion of the tension test data is included to help guide future work.
Open AccessEffect of Processing Parameters on the Mechanical Behavior of 3D-Printed Basalt Moon Dust Reinforced Polylactic Acid Composites
Advanced composite materials and manufacturing technologies are critical to sustain human presence in space. Mechanical testing and analysis are needed to elucidate the effect of processing parameters on composites’ material properties. In this study, test specimens are 3D printed via a fused-filament fabrication (FFF) approach from a basalt moon dust-polylactic acid (BMD-PLA) composite filament and from pure PLA filament. Compression and tensile testing were conducted to determine the yield strength, ultimate strength, and Young’s modulus of specimens fabricated under several processing conditions. The maximum compressive yield strength for the BMD-reinforced samples is 27.68 MPa with print parameters of 100% infill, one shell, and 90° print orientation. The maximum compressive yield strength for the PLA samples is 63.05 MPa with print parameters of 100% infill, three shells, and 0° print orientation. The composite samples exhibit an increase in strength when layer lines are aligned with loading axis, whereas the PLA samples decreased in strength. This indicates a fundamental difference in how the composite behaves in comparison to the pure matrix material. In tension, test specimens have unpredictable failure modes and often broke outside the gauge length. A portion of the tension test data is included to help guide future work.
- Open Access
A Comprehensive Analysis of Thermal Heat Dissipation for Lithium-Ion Battery Packs
Effective thermal management is essential for the safe and efficient operation of lithium-ion battery packs, particularly in compact, airflow-sensitive applications such as drones. This study presents a comprehensive thermal analysis of a 16-cell lithium-ion battery pack by exploring seven geometric configurations under airflow speeds ranging from 0 to 15 m/s and integrating nano-carbon-based phase change materials (PCMs) to enhance heat dissipation. A Computational Fluid Dynamics (CFD) approach was employed using Ansys Discovery and Workbench 2024 R1 to simulate airflow and heat transfer processes with high spatial resolution. Using high-fidelity 3D simulations, we found that the trapezoidal wide-base configuration, combined with a 5-inlet and 1-outlet airflow design, achieved the most balanced cooling performance across all speed regimes. This configuration maintained battery temperatures within the optimal operating range (∼45 °C) in both low- and high-speed airflow conditions, with a maximum temperature reduction of up to 8.3 °C compared to the standard square configuration. Additionally, PCM integration extended the thermal regulation duration to approximately 12.5 min, effectively buffering thermal spikes during peak loads. These findings underscore the critical role of CFD-driven geometric optimization and advanced material integration in designing high-efficiency, compact cooling systems for energy-dense battery applications in drones and portable electronics.
Open AccessA Comprehensive Analysis of Thermal Heat Dissipation for Lithium-Ion Battery Packs
Effective thermal management is essential for the safe and efficient operation of lithium-ion battery packs, particularly in compact, airflow-sensitive applications such as drones. This study presents a comprehensive thermal analysis of a 16-cell lithium-ion battery pack by exploring seven geometric configurations under airflow speeds ranging from 0 to 15 m/s and integrating nano-carbon-based phase change materials (PCMs) to enhance heat dissipation. A Computational Fluid Dynamics (CFD) approach was employed using Ansys Discovery and Workbench 2024 R1 to simulate airflow and heat transfer processes with high spatial resolution. Using high-fidelity 3D simulations, we found that the trapezoidal wide-base configuration, combined with a 5-inlet and 1-outlet airflow design, achieved the most balanced cooling performance across all speed regimes. This configuration maintained battery temperatures within the optimal operating range (∼45 °C) in both low- and high-speed airflow conditions, with a maximum temperature reduction of up to 8.3 °C compared to the standard square configuration. Additionally, PCM integration extended the thermal regulation duration to approximately 12.5 min, effectively buffering thermal spikes during peak loads. These findings underscore the critical role of CFD-driven geometric optimization and advanced material integration in designing high-efficiency, compact cooling systems for energy-dense battery applications in drones and portable electronics.
- Open Access
Comprehensive Analysis of Thermal Dissipation in Lithium-Ion Battery Packs
Effective thermal management is critical for lithium-ion battery packs' safe and efficient operations, particularly in applications such as drones, where compact designs and varying airflow conditions present unique challenges. This study investigates the thermal performance of a 16-cell lithium-ion battery pack by optimizing cooling airflow configurations and integrating phase change materials (PCMs) for enhanced heat dissipation. Seven geometric configurations were evaluated under airflow speeds ranging from 0 to 15 m/s, reflecting the operational conditions of civilian drones. A comprehensive 3D simulation approach was used to analyze the effects of inlet and outlet configurations, airflow dynamics, and PCM phase transition behavior. Results indicate that the trapezoidal (wide-base) configuration, paired with a 5-inlet and 1-outlet setup, achieves the most balanced performance, effectively maintaining optimal operating temperatures across low and high-speed airflow conditions. PCM integration further stabilized thermal behavior, with phase change durations extending to 12.5 min under tested conditions. These findings highlight the importance of geometric optimization and material integration in advancing compact and reliable thermal management systems for energy-dense battery packs. This study provides a foundation for designing efficient cooling strategies tailored to lightweight applications such as drones and portable energy storage systems.
Open AccessComprehensive Analysis of Thermal Dissipation in Lithium-Ion Battery Packs
Effective thermal management is critical for lithium-ion battery packs' safe and efficient operations, particularly in applications such as drones, where compact designs and varying airflow conditions present unique challenges. This study investigates the thermal performance of a 16-cell lithium-ion battery pack by optimizing cooling airflow configurations and integrating phase change materials (PCMs) for enhanced heat dissipation. Seven geometric configurations were evaluated under airflow speeds ranging from 0 to 15 m/s, reflecting the operational conditions of civilian drones. A comprehensive 3D simulation approach was used to analyze the effects of inlet and outlet configurations, airflow dynamics, and PCM phase transition behavior. Results indicate that the trapezoidal (wide-base) configuration, paired with a 5-inlet and 1-outlet setup, achieves the most balanced performance, effectively maintaining optimal operating temperatures across low and high-speed airflow conditions. PCM integration further stabilized thermal behavior, with phase change durations extending to 12.5 min under tested conditions. These findings highlight the importance of geometric optimization and material integration in advancing compact and reliable thermal management systems for energy-dense battery packs. This study provides a foundation for designing efficient cooling strategies tailored to lightweight applications such as drones and portable energy storage systems.
- Open Access
Compressive Properties of Additively Manufactured Metal-Reinforced PLA and ABS Composites
The development of multi-material filaments has enabled fused filament fabrication-based additive manufacturing to address demand for high-performance lightweight multifunctional components. In this study, polylactic acid (PLA) and acrylonitrile butadiene styrene based filaments with metallic reinforcements of magnetic iron (MI), stainless steel (SS), bronze (Br), copper (Cu), Bismuth (Bi), and Tungsten (W) were investigated to elucidate their complex processing–structure–property relationships. The microstructure of 3D-printed materials were characterized by microscopy and analyzed to determine the metal cross-sectional area percentage and the relationship between metal reinforcement, the polymer matrix, and porosity. Compression testing was conducted in directions parallel and perpendicular to the build direction in order to evaluate the effect of orientation and metal reinforcement on the mechanical properties. 3D-printed specimens experienced either fracture through print layers or layer-wise interfacial rupture for loads applied perpendicular and parallel to the print layers, respectively. A dependence of yield strength on loading orientation was observed for Br-PLA, Cu-PLA, SS-PLA, Bi-ABS, and W-ABS; however, MI-PLA and pure ABS specimens did not exhibit this sensitivity. Metal reinforcement also influenced the magnitude of compressive yield strength, with MI-PLA and SS-PLA demonstrating increased strength over Br-PLA and Cu-PLA, while ABS demonstrated increased strength over Bi-ABS and W-ABS. These results demonstrate the importance of considering orientation in printing and applications, the trade-off between various metallic reinforcements for added multifunctionality, and the potential of these tailored polymer composites for novel 3D-printed structures.
Open AccessCompressive Properties of Additively Manufactured Metal-Reinforced PLA and ABS Composites
The development of multi-material filaments has enabled fused filament fabrication-based additive manufacturing to address demand for high-performance lightweight multifunctional components. In this study, polylactic acid (PLA) and acrylonitrile butadiene styrene based filaments with metallic reinforcements of magnetic iron (MI), stainless steel (SS), bronze (Br), copper (Cu), Bismuth (Bi), and Tungsten (W) were investigated to elucidate their complex processing–structure–property relationships. The microstructure of 3D-printed materials were characterized by microscopy and analyzed to determine the metal cross-sectional area percentage and the relationship between metal reinforcement, the polymer matrix, and porosity. Compression testing was conducted in directions parallel and perpendicular to the build direction in order to evaluate the effect of orientation and metal reinforcement on the mechanical properties. 3D-printed specimens experienced either fracture through print layers or layer-wise interfacial rupture for loads applied perpendicular and parallel to the print layers, respectively. A dependence of yield strength on loading orientation was observed for Br-PLA, Cu-PLA, SS-PLA, Bi-ABS, and W-ABS; however, MI-PLA and pure ABS specimens did not exhibit this sensitivity. Metal reinforcement also influenced the magnitude of compressive yield strength, with MI-PLA and SS-PLA demonstrating increased strength over Br-PLA and Cu-PLA, while ABS demonstrated increased strength over Bi-ABS and W-ABS. These results demonstrate the importance of considering orientation in printing and applications, the trade-off between various metallic reinforcements for added multifunctionality, and the potential of these tailored polymer composites for novel 3D-printed structures.
- Open Access
- 11 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 254
Development and optimization of hybrid heat dissipation system for lithium-ion battery packs
- 11 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 254
Open AccessDevelopment and optimization of hybrid heat dissipation system for lithium-ion battery packs
- Open Access
Additively Manufactured Carbon-Reinforced ABS Honeycomb Composite Structures and Property Prediction by Machine Learning
The expansive utility of polymeric 3D-printing technologies and demand for high- performance lightweight structures has prompted the emergence of various carbon-reinforced polymer composite filaments. However, detailed characterization of the processing–microstructure–property relationships of these materials is still required to realize their full potential. In this study, acrylonitrile butadiene styrene (ABS) and two carbon-reinforced ABS variants, with either carbon nanotubes (CNT) or 5 wt.% chopped carbon fiber (CF), were designed in a bio-inspired honeycomb geometry. These structures were manufactured by fused filament fabrication (FFF) and investigated across a range of layer thicknesses and hexagonal (hex) sizes. Microscopy of material cross-sections was conducted to evaluate the relationship between print parameters and porosity. Analyses determined a trend of reduced porosity with lower print-layer heights and hex sizes compared to larger print-layer heights and hex sizes. Mechanical properties were evaluated through compression testing, with ABS specimens achieving higher compressive yield strength, while CNT-ABS achieved higher ultimate compressive strength due to the reduction in porosity and subsequent strengthening. A trend of decreasing strength with increasing hex size across all materials was supported by the negative correlation between porosity and increasing print-layer height and hex size. We elucidated the potential of honeycomb ABS, CNT-ABS, and ABS-5wt.% CF polymer composites for novel 3D-printed structures. These studies were supported by the development of a predictive classification and regression supervised machine learning model with 0.92 accuracy and a 0.96 coefficient of determination to help inform and guide design for targeted performance.
Open AccessAdditively Manufactured Carbon-Reinforced ABS Honeycomb Composite Structures and Property Prediction by Machine Learning
The expansive utility of polymeric 3D-printing technologies and demand for high- performance lightweight structures has prompted the emergence of various carbon-reinforced polymer composite filaments. However, detailed characterization of the processing–microstructure–property relationships of these materials is still required to realize their full potential. In this study, acrylonitrile butadiene styrene (ABS) and two carbon-reinforced ABS variants, with either carbon nanotubes (CNT) or 5 wt.% chopped carbon fiber (CF), were designed in a bio-inspired honeycomb geometry. These structures were manufactured by fused filament fabrication (FFF) and investigated across a range of layer thicknesses and hexagonal (hex) sizes. Microscopy of material cross-sections was conducted to evaluate the relationship between print parameters and porosity. Analyses determined a trend of reduced porosity with lower print-layer heights and hex sizes compared to larger print-layer heights and hex sizes. Mechanical properties were evaluated through compression testing, with ABS specimens achieving higher compressive yield strength, while CNT-ABS achieved higher ultimate compressive strength due to the reduction in porosity and subsequent strengthening. A trend of decreasing strength with increasing hex size across all materials was supported by the negative correlation between porosity and increasing print-layer height and hex size. We elucidated the potential of honeycomb ABS, CNT-ABS, and ABS-5wt.% CF polymer composites for novel 3D-printed structures. These studies were supported by the development of a predictive classification and regression supervised machine learning model with 0.92 accuracy and a 0.96 coefficient of determination to help inform and guide design for targeted performance.
- Open Access
Multi-Material Additive Manufacturing of High Temperature Polyetherimide (PEI)–Based Polymer Systems for Lightweight Aerospace Applications
Rapid innovations in 3-D printing technology have created a demand for multifunctional composites. Advanced polymers like amorphous thermoplastic polyetherimide (PEI) can create robust, lightweight, and efficient structures while providing high-temperature stability. This work manufactured ULTEM, a PEI-based polymer, and carbon-fiber-infused ULTEM multi-material composites with varying layering patterns (e.g., AAABBB vs. ABABAB) using fused filament fabrication (FFF). The microstructure of fractured surfaces and polished cross-sections determined that the print quality of layers printed closer to the heated bed was higher than layers closer to the top surface, primarily due to the thermal insulating properties of the material itself. Mechanical properties of the multi-material parts were between those of the single-material parts: an ultimate tensile strength and elastic modulus of 59 MPa and 3.005 GPa, respectively. Multi-material parts from the same filaments but with different layering patterns showed different mechanical responses. Prints were of higher quality and demonstrated a higher elastic modulus (3.080 GPa) when consecutive layers were printed from the same filament (AAABBB) versus parts with printed layers of alternating filaments (ABABAB), which showed a higher ultimate strength (62.04 MPa). These results demonstrate the potential for creatively designing multi-material printed parts that may enhance mechanical properties.
Open AccessMulti-Material Additive Manufacturing of High Temperature Polyetherimide (PEI)–Based Polymer Systems for Lightweight Aerospace Applications
Rapid innovations in 3-D printing technology have created a demand for multifunctional composites. Advanced polymers like amorphous thermoplastic polyetherimide (PEI) can create robust, lightweight, and efficient structures while providing high-temperature stability. This work manufactured ULTEM, a PEI-based polymer, and carbon-fiber-infused ULTEM multi-material composites with varying layering patterns (e.g., AAABBB vs. ABABAB) using fused filament fabrication (FFF). The microstructure of fractured surfaces and polished cross-sections determined that the print quality of layers printed closer to the heated bed was higher than layers closer to the top surface, primarily due to the thermal insulating properties of the material itself. Mechanical properties of the multi-material parts were between those of the single-material parts: an ultimate tensile strength and elastic modulus of 59 MPa and 3.005 GPa, respectively. Multi-material parts from the same filaments but with different layering patterns showed different mechanical responses. Prints were of higher quality and demonstrated a higher elastic modulus (3.080 GPa) when consecutive layers were printed from the same filament (AAABBB) versus parts with printed layers of alternating filaments (ABABAB), which showed a higher ultimate strength (62.04 MPa). These results demonstrate the potential for creatively designing multi-material printed parts that may enhance mechanical properties.