Duncan Hay
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Duncan Hay has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Larry Weber
IIHR, Hydroscience & Engineering, The University of Iowa, 300 South Riverside Dr., Iowa City, IA 52242-1585
3 shared publications - Marcela Politano
IIHR, Hydroscience & Engineering, The University of Iowa, 300 South Riverside Dr., Iowa City, IA 52242-1585
2 shared publications - Pablo M. Carrica
IIHR-Hydroscience and Engineering, The University of Iowa 1 , Iowa City, Iowa 52242, USA
2 shared publications - Troy Lyons
IAHR Member), Director of Engineering Services, IIHR-Hydroscience & Engineering, The University of Iowa, Iowa City, IA, USA
2 shared publications - Antonio Arenas
Department of Civil, Construction, and Environmental Engineering, Iowa State University, 813 Bissell Rd, Ames, IA 50011, USA
1 shared publication - Cagri Turan
IIHR, Hydroscience & Engineering, The University of Iowa, 300 South Riverside Dr., Iowa City, IA 52242-1585
1 shared publication
Latest Publications
- 1 October 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 137 (10) , 1257-1268
Investigation into the Total Dissolved Gas Dynamics of Wells Dam Using a Two-Phase Flow Model
Bubbles entrained by spilled water at hydroelectric projects increase the concentration of total dissolved gas (TDG), which may lead to gas bubble disease in fish. In this paper, the TDG dynamics downstream of Wells Dam are investigated using a two-phase flow model that accounts for the effect of the bubbles on the flow field. The TDG is calculated with a transport equation in which the source is the bubble/liquid mass transfer, a function of the gas volume fraction and bubble size. The model uses anisotropic turbulence modeling and includes attenuation of normal fluctuation at the free surface to capture the flow field and TDG mixing. The model is validated using velocity and TDG field data. Simulations under two plant operational configurations are performed to gain a better understanding of the effect of spill operations on the production, transport, and mixing of TDG. Model results indicate that concentrated spill releases create surface jets that result in the lowest TDG concentration downstream. On ...
- 1 October 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 137 (10) , 1257-1268
Investigation into the Total Dissolved Gas Dynamics of Wells Dam Using a Two-Phase Flow Model
Bubbles entrained by spilled water at hydroelectric projects increase the concentration of total dissolved gas (TDG), which may lead to gas bubble disease in fish. In this paper, the TDG dynamics downstream of Wells Dam are investigated using a two-phase flow model that accounts for the effect of the bubbles on the flow field. The TDG is calculated with a transport equation in which the source is the bubble/liquid mass transfer, a function of the gas volume fraction and bubble size. The model uses anisotropic turbulence modeling and includes attenuation of normal fluctuation at the free surface to capture the flow field and TDG mixing. The model is validated using velocity and TDG field data. Simulations under two plant operational configurations are performed to gain a better understanding of the effect of spill operations on the production, transport, and mixing of TDG. Model results indicate that concentrated spill releases create surface jets that result in the lowest TDG concentration downstream. On ...
- 1 August 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 134 (8) , 1172-1175
Study of the Free Surface Flow on an Ogee-Crested Fish Bypass
A study of the free surface flow on an ogee-crested fish bypass is presented. The commercial computational fluid dynamics (CFD) code Fluent 6.1 was used to perform the simulations. Structured/unstructured hybrid grids were used to accommodate the complex geometry that included gate slots, flow control gates, and an aeration slot. The volume of fluid (VOF) approach was used to model the water/air interface. The fish bypass exhibits complex free surface features including free nappes and air entrainment from the air slots. Free surface elevations on both sides of the nappe, pressure along the ogee surface, and discharge rating curves were compared against 1:24 experimental data from the laboratory model for different headwater elevations and gate settings. Limited comparison against measured velocities was also performed. Once deemed reliable through validation against experimental data, the computational model was used to analyze the flow field, supplementing the areas of limited experimental data. Though the paper presents the final fish bypass design, CFD was used to guide the design process and provide insight for several variations in the geometry.
- 1 August 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 134 (8) , 1172-1175
Study of the Free Surface Flow on an Ogee-Crested Fish Bypass
A study of the free surface flow on an ogee-crested fish bypass is presented. The commercial computational fluid dynamics (CFD) code Fluent 6.1 was used to perform the simulations. Structured/unstructured hybrid grids were used to accommodate the complex geometry that included gate slots, flow control gates, and an aeration slot. The volume of fluid (VOF) approach was used to model the water/air interface. The fish bypass exhibits complex free surface features including free nappes and air entrainment from the air slots. Free surface elevations on both sides of the nappe, pressure along the ogee surface, and discharge rating curves were compared against 1:24 experimental data from the laboratory model for different headwater elevations and gate settings. Limited comparison against measured velocities was also performed. Once deemed reliable through validation against experimental data, the computational model was used to analyze the flow field, supplementing the areas of limited experimental data. Though the paper presents the final fish bypass design, CFD was used to guide the design process and provide insight for several variations in the geometry.
- 19 May 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Model Study for the Design of Emergency Stoplogs Deployed in a ComplexFlow Field — Part 1: Experimental Results
The model study objective is to determine the optimum configuration for a multi-segment cable-deployed vertical gate to block flow through a fish bypass when primary gates are not functional. In such emergency situations, gate segments are subjected to complex three-dimensional flows that vary with gate deployment elevation. The 1:24 scale model incorporated a comprehensive experimental setup controlled by LabVIEW data acquisition and visualization software allowing real-time measurement and visualization of the forces during gate deployment. Thirty gate segments (stoplogs) and lifting beam shape combinations were tested to minimize submerged gate closure weight and measure maximum cable tension. The experimental tests were complemented by companion Computational Fluid Dynamic (CFD) simulations aimed at substantiating the flow features and directing the phasing of the experimental program. This paper describes the experimental setup, procedures, and experimental phasing, as well as synergistic use of laboratory and CFD data.
- 19 May 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Model Study for the Design of Emergency Stoplogs Deployed in a ComplexFlow Field — Part 1: Experimental Results
The model study objective is to determine the optimum configuration for a multi-segment cable-deployed vertical gate to block flow through a fish bypass when primary gates are not functional. In such emergency situations, gate segments are subjected to complex three-dimensional flows that vary with gate deployment elevation. The 1:24 scale model incorporated a comprehensive experimental setup controlled by LabVIEW data acquisition and visualization software allowing real-time measurement and visualization of the forces during gate deployment. Thirty gate segments (stoplogs) and lifting beam shape combinations were tested to minimize submerged gate closure weight and measure maximum cable tension. The experimental tests were complemented by companion Computational Fluid Dynamic (CFD) simulations aimed at substantiating the flow features and directing the phasing of the experimental program. This paper describes the experimental setup, procedures, and experimental phasing, as well as synergistic use of laboratory and CFD data.
- 19 May 2006
- Published by American Society of Civil Engineers (ASCE)
Model Study for the Design of Emergency Stoplogs Deployed in a ComplexFlow Field — Part 2: Numerical Results
An emergency closure system using stoplogs was designed to stop the flow through a fish passage when the primary gates are not functional. Physical and numerical hydraulic models were conducted to develop the stoplog design for the Wanapum Future Unit Fish Bypass. Different design alternatives were evaluated to minimize the maximum cable tension during deployment and the hydraulic uplift force that could prevent closure. The hydraulic force on the stoplog and lifting beam were calculated using the commercial code Fluent. The Volume of Fluid (VOF) method was used to simulate the free surface. Structured and unstructured hybrid grids were used to simulate the complex geometry near the stoplogs. The predicted flow field for the stoplogs at different elevations are presented and discussed. Two-dimensional numerical results are compared against experimental data taken on the 1:24 scale laboratory model and used to understand the physics underlying the behavior of each geometric design.
- 19 May 2006
- Published by American Society of Civil Engineers (ASCE)
Model Study for the Design of Emergency Stoplogs Deployed in a ComplexFlow Field — Part 2: Numerical Results
An emergency closure system using stoplogs was designed to stop the flow through a fish passage when the primary gates are not functional. Physical and numerical hydraulic models were conducted to develop the stoplog design for the Wanapum Future Unit Fish Bypass. Different design alternatives were evaluated to minimize the maximum cable tension during deployment and the hydraulic uplift force that could prevent closure. The hydraulic force on the stoplog and lifting beam were calculated using the commercial code Fluent. The Volume of Fluid (VOF) method was used to simulate the free surface. Structured and unstructured hybrid grids were used to simulate the complex geometry near the stoplogs. The predicted flow field for the stoplogs at different elevations are presented and discussed. Two-dimensional numerical results are compared against experimental data taken on the 1:24 scale laboratory model and used to understand the physics underlying the behavior of each geometric design.