Theodore G. Cleveland
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Theodore G. Cleveland has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- David B. Thompson
Director of Engineering, R.O. Anderson Engineering, Inc., Minden, NV 89423
8 shared publications - Xing Fang
Auburn Univ
7 shared publications Nirajan Dhakal
Research Assistant, Dept. of Civil Engineering, Auburn Univ., Auburn, AL 36849-5337
3 shared publications- William H. Asquith
Interior U.S. Geological GEORGIA ARKANSAS MISSISSIPPI TENNESSEE INDIANA ILLINOIS IOWA OHIO ALABAMA MISSOURI OKLAHOMA LOUISIANA
3 shared publications - Luke J. Marzen
Department of Geosciences, Auburn University, Auburn, AL 36849, USA
2 shared publications - Ming-Han Li
Department of Landscape Architecture and Urban Planning, Texas A&M University, College Station, TX 77843-3137, USA
2 shared publications
Latest Publications
- 1 March 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydrologic Engineering
- Vol. 19 (3) , 495-508
Improved Time of Concentration Estimation on Overland Flow Surfaces Including Low-Sloped Planes
Time of concentration ( ) is one of the most used time parameters in hydrologic analyses. As topographic slope ( ) approaches zero, traditional estimation formulas predict large . Based on numerical modeling and a review of relevant literature, a lower bound for slope ( ) of 0.1% was identified as a threshold below which traditional estimation formulas become unreliable and alternate methods should be considered. In this study, slopes less than are defined as low slopes. Slopes equal to or exceeding are defined as standard slopes where traditional estimation formulas are appropriate. A field study was conducted on a concrete plot with a topographic slope of 0.25% to collect rainfall and runoff data between April 2009 and March 2010 to support numerical modeling of overland flows on low-sloped planes. A quasi-two-dimensional dynamic wave model (Q2DWM) was developed for overland flow simulation and validated using published and observed data. The validated Q2DWM was used in a parametric study to generate data for a range of slopes that were used to develop regression formulas for standard slopes ( ) and low slopes ( ).- 1 March 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydrologic Engineering
- Vol. 19 (3) , 495-508
Improved Time of Concentration Estimation on Overland Flow Surfaces Including Low-Sloped Planes
Time of concentration ( ) is one of the most used time parameters in hydrologic analyses. As topographic slope ( ) approaches zero, traditional estimation formulas predict large . Based on numerical modeling and a review of relevant literature, a lower bound for slope ( ) of 0.1% was identified as a threshold below which traditional estimation formulas become unreliable and alternate methods should be considered. In this study, slopes less than are defined as low slopes. Slopes equal to or exceeding are defined as standard slopes where traditional estimation formulas are appropriate. A field study was conducted on a concrete plot with a topographic slope of 0.25% to collect rainfall and runoff data between April 2009 and March 2010 to support numerical modeling of overland flows on low-sloped planes. A quasi-two-dimensional dynamic wave model (Q2DWM) was developed for overland flow simulation and validated using published and observed data. The validated Q2DWM was used in a parametric study to generate data for a range of slopes that were used to develop regression formulas for standard slopes ( ) and low slopes ( ).- 1 December 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydrologic Engineering
- Vol. 18 (12) , 1571-1580
Rate-Based Estimation of the Runoff Coefficients for Selected Watersheds in Texas
The runoff coefficient, , of the rational method is an expression of rate proportionality between rainfall intensity and peak discharge. Values of were derived for 80 developed and undeveloped watersheds in Texas using two distinct methods. First, the rate-based runoff coefficient, , was estimated for each of about 1,500 rainfall-runoff events. Second, the frequency-matching approach was used to derive a runoff coefficient, , for each watershed. Published values, , or literature-based runoff coefficients were compared to those obtained from the methods investigated here. Using the 80 Texas watersheds, comparison of the two methods shows that about 75% of literature-based runoff coefficients are greater than and the watershed-median , but for developed watersheds with more impervious cover, literature-based runoff coefficients are less than and . An equation applicable to many Texas watersheds is proposed to estimate as a function of impervious area.- 1 December 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydrologic Engineering
- Vol. 18 (12) , 1571-1580
Rate-Based Estimation of the Runoff Coefficients for Selected Watersheds in Texas
The runoff coefficient, , of the rational method is an expression of rate proportionality between rainfall intensity and peak discharge. Values of were derived for 80 developed and undeveloped watersheds in Texas using two distinct methods. First, the rate-based runoff coefficient, , was estimated for each of about 1,500 rainfall-runoff events. Second, the frequency-matching approach was used to derive a runoff coefficient, , for each watershed. Published values, , or literature-based runoff coefficients were compared to those obtained from the methods investigated here. Using the 80 Texas watersheds, comparison of the two methods shows that about 75% of literature-based runoff coefficients are greater than and the watershed-median , but for developed watersheds with more impervious cover, literature-based runoff coefficients are less than and . An equation applicable to many Texas watersheds is proposed to estimate as a function of impervious area.- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 603-618
Watershed Slope Lower Bounds for Hydrologic Methods
Engineers design a substantial fraction portion of infrastructure that accommodates storm water drainage and conveyance. Estimation models of the response for a watershed typically contain some form of watershed slope as a principal parameter, and the response is usually inversely proportional to that slope. Therefore, as topographic slope decreases, the watershed timing parameter increases. The consequences at low enough slope, is that the timing parameters approach infinite time and the precipitation intensity that is associated with a long averaging time is so small as to be meaningless -- yet low slope environments exist, are populated, and precipitation does generate runoff.
- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 603-618
Watershed Slope Lower Bounds for Hydrologic Methods
Engineers design a substantial fraction portion of infrastructure that accommodates storm water drainage and conveyance. Estimation models of the response for a watershed typically contain some form of watershed slope as a principal parameter, and the response is usually inversely proportional to that slope. Therefore, as topographic slope decreases, the watershed timing parameter increases. The consequences at low enough slope, is that the timing parameters approach infinite time and the precipitation intensity that is associated with a long averaging time is so small as to be meaningless -- yet low slope environments exist, are populated, and precipitation does generate runoff.
- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 360-371
Estimating Time of Concentration on Low-Slope Planes Using Diffusion Hydrodynamic Model
The time of concentration (Tc) is an important parameter for hydrologic design, analysis, and modeling. Error in the estimation of Tc will cause error in prediction of peak discharge (Qp), resulting in an incorrect design. Overland flow Tc depends on several factors, such as rainfall intensity (i), length (L), topographic slope (S0), and flow resistance (n). Generally, Tc has an inverse relation to S0. For the areas with very small or zero S0, use of such small values for S0 in traditional methods (empirical equations) for estimating Tc can produce very large values of Tc that seem to be unrealistic and incorrect. This study was conducted to identify a lower slope bound (SLB) for the use of traditional equations in determination of Tc and to propose the use of an alternate method for the determination of Tc on low-slope planes. The diffusion hydrodynamic model (DHM) was validated using data collected from published studies and field data collected in this study, including observed rainfall hyetographs and runoff hydrographs for 27 rainfall events for watersheds with relatively low-slope. After model validation, DHM was used to generate parametric relations between Tc and its explanatory variables (rainfall intensity, length, slope and resistance to flow) and extend the regression model to low-slope planes.
- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 360-371
Estimating Time of Concentration on Low-Slope Planes Using Diffusion Hydrodynamic Model
The time of concentration (Tc) is an important parameter for hydrologic design, analysis, and modeling. Error in the estimation of Tc will cause error in prediction of peak discharge (Qp), resulting in an incorrect design. Overland flow Tc depends on several factors, such as rainfall intensity (i), length (L), topographic slope (S0), and flow resistance (n). Generally, Tc has an inverse relation to S0. For the areas with very small or zero S0, use of such small values for S0 in traditional methods (empirical equations) for estimating Tc can produce very large values of Tc that seem to be unrealistic and incorrect. This study was conducted to identify a lower slope bound (SLB) for the use of traditional equations in determination of Tc and to propose the use of an alternate method for the determination of Tc on low-slope planes. The diffusion hydrodynamic model (DHM) was validated using data collected from published studies and field data collected in this study, including observed rainfall hyetographs and runoff hydrographs for 27 rainfall events for watersheds with relatively low-slope. After model validation, DHM was used to generate parametric relations between Tc and its explanatory variables (rainfall intensity, length, slope and resistance to flow) and extend the regression model to low-slope planes.
- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 138 (1) , 43-54
Estimation of Volumetric Runoff Coefficients for Texas Watersheds Using Land-Use and Rainfall-Runoff Data
The rational method for peak discharge ( ) estimation was introduced in the 1880s. Although the rational method is considered simplistic, it remains an effective method for estimating peak discharge for small watersheds. The runoff coefficient ( ) is a key parameter for the rational method and can be estimated in various ways. Literature-based values ( ) are listed for different land-use/land cover (two words, no hyphen) (LULC) conditions in various design manuals and textbooks; however, these values were developed with little basis on observed rainfall and runoff data. In this paper, values were derived for 90 watersheds in Texas by using LULC data for 1992 and 2001; the values derived from the two data sets were essentially the same. Also for this study, volumetric runoff coefficients ( ) were estimated by using observed rainfall and runoff depths from more than 1,600 events observed in the watersheds. Watershed-median and watershed-average values were computed, and both are consistent with data from the National Urban Runoff Program. In addition, values were estimated by using rank-ordered pairs of rainfall and runoff depths (i.e., frequency matching). As anticipated, values derived by all three methods (literature based, event totals, and frequency matching) consistently had larger values for developed watersheds than for undeveloped watersheds. Two regression equations of versus percent impervious area were developed and combined into a single equation that can be used to rapidly estimate values for similar Texas watersheds.- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 138 (1) , 43-54
Estimation of Volumetric Runoff Coefficients for Texas Watersheds Using Land-Use and Rainfall-Runoff Data
The rational method for peak discharge ( ) estimation was introduced in the 1880s. Although the rational method is considered simplistic, it remains an effective method for estimating peak discharge for small watersheds. The runoff coefficient ( ) is a key parameter for the rational method and can be estimated in various ways. Literature-based values ( ) are listed for different land-use/land cover (two words, no hyphen) (LULC) conditions in various design manuals and textbooks; however, these values were developed with little basis on observed rainfall and runoff data. In this paper, values were derived for 90 watersheds in Texas by using LULC data for 1992 and 2001; the values derived from the two data sets were essentially the same. Also for this study, volumetric runoff coefficients ( ) were estimated by using observed rainfall and runoff depths from more than 1,600 events observed in the watersheds. Watershed-median and watershed-average values were computed, and both are consistent with data from the National Urban Runoff Program. In addition, values were estimated by using rank-ordered pairs of rainfall and runoff depths (i.e., frequency matching). As anticipated, values derived by all three methods (literature based, event totals, and frequency matching) consistently had larger values for developed watersheds than for undeveloped watersheds. Two regression equations of versus percent impervious area were developed and combined into a single equation that can be used to rapidly estimate values for similar Texas watersheds.- 19 May 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 751-762
Revisiting Modified Rational Method
The rational method was originally developed to estimate peak discharges for sizing drainage structures, such as storm drains and culverts. The modified rational method (MRM) is an extension of the rational method to produce simple runoff hydrographs. The MRM is often called the rational hydrograph method. Application of the MRM produces a runoff hydrograph and runoff volume in contrast to application of the rational method, which produces only the peak design discharge (Qp). The hydrograph developed from application of the MRM is a special case of the unit hydrograph method and will be termed the modified rational unit hydrograph (MRUH) in this paper. Being a unit hydrograph, the MRUH can be applied to nonuniform rainfall distributions. Furthermore, the MRUH can be used on watersheds with drainage areas in excess of the typical limit for application of the rational method (a few hundred acres). The MRUH method was applied to 90 watersheds in Texas. Application of the MRUH method involved two steps: (1) determination of rainfall loss using rational method concept, that is, use of the runoff coefficient, and (2) determination of the MRUH using drainage area (A) and time of concentration (Tc) as input parameters, in addition to applying the procedure of unit hydrograph convolution. Time of concentration was estimated using two methods: (1) the Kirpich method and (2) the square root of watershed drainage area. Runoff coefficients for application of the MRUH were estimated using two methods: The first estimate of the runoff coefficient was a watershed composite literature-based runoff coefficient (Clit) derived using the land-use information for the watershed and published Clit values for various land-uses. The second estimate of the runoff coefficient was a back-computed volumetric runoff coefficient, Cvbc, determined by preserving the runoff volume and using observed rainfall and runoff data. Time interval used for unit hydrograph convolution was 5 minutes. Both predicted and observed discharge hydrograph ordinates were reported and compared using the same time interval. The MRUH method performed about as well as other unit hydrograph methods including the Gamma unit hydrograph and HEC-1 unit hydrograph in predicting the peak discharge of the direct runoff hydrograph, when the same rainfall loss model was used.
- 19 May 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 751-762
Revisiting Modified Rational Method
The rational method was originally developed to estimate peak discharges for sizing drainage structures, such as storm drains and culverts. The modified rational method (MRM) is an extension of the rational method to produce simple runoff hydrographs. The MRM is often called the rational hydrograph method. Application of the MRM produces a runoff hydrograph and runoff volume in contrast to application of the rational method, which produces only the peak design discharge (Qp). The hydrograph developed from application of the MRM is a special case of the unit hydrograph method and will be termed the modified rational unit hydrograph (MRUH) in this paper. Being a unit hydrograph, the MRUH can be applied to nonuniform rainfall distributions. Furthermore, the MRUH can be used on watersheds with drainage areas in excess of the typical limit for application of the rational method (a few hundred acres). The MRUH method was applied to 90 watersheds in Texas. Application of the MRUH method involved two steps: (1) determination of rainfall loss using rational method concept, that is, use of the runoff coefficient, and (2) determination of the MRUH using drainage area (A) and time of concentration (Tc) as input parameters, in addition to applying the procedure of unit hydrograph convolution. Time of concentration was estimated using two methods: (1) the Kirpich method and (2) the square root of watershed drainage area. Runoff coefficients for application of the MRUH were estimated using two methods: The first estimate of the runoff coefficient was a watershed composite literature-based runoff coefficient (Clit) derived using the land-use information for the watershed and published Clit values for various land-uses. The second estimate of the runoff coefficient was a back-computed volumetric runoff coefficient, Cvbc, determined by preserving the runoff volume and using observed rainfall and runoff data. Time interval used for unit hydrograph convolution was 5 minutes. Both predicted and observed discharge hydrograph ordinates were reported and compared using the same time interval. The MRUH method performed about as well as other unit hydrograph methods including the Gamma unit hydrograph and HEC-1 unit hydrograph in predicting the peak discharge of the direct runoff hydrograph, when the same rainfall loss model was used.
- 14 May 2010
- Published by American Society of Civil Engineers (ASCE)
- p. 3339-3348
Estimation of Rational Runoff Coefficients for Texas Watersheds
The rational method introduced in 1880s is often considered simplistic and still frequently used for estimating peak discharges for small drainage areas. The runoff coefficient (C) is a key parameter for the rational method, and typical C values are given and listed in various design manuals and textbooks for different land use conditions. Actually, these C values were developed without much support of observed data. This paper presents an in-depth literature review on the rational method and developed literature-based runoff coefficients estimated from land use data in 1992 and 2001 for 90 watersheds in central Texas. There is no statistically significant change on C values derived from two land use data. Runoff coefficients were also estimated from observed rainfall and runoff data of more than 1600 events in these watersheds. Distributions of runoff coefficients and watershed mean values are analyzed. Using watershed parameters (e.g., drainage area, slope, and channel length) and regression equations of discharge at different return periods we estimated runoff coefficients in these watersheds for the return periods of 2-, 5-, 10-, 25-, 50-, and 100-years. The rational runoff coefficients increase with the return period and the rate of increase is much larger than what typically recommended in design manuals.
- 14 May 2010
- Published by American Society of Civil Engineers (ASCE)
- p. 3339-3348
Estimation of Rational Runoff Coefficients for Texas Watersheds
The rational method introduced in 1880s is often considered simplistic and still frequently used for estimating peak discharges for small drainage areas. The runoff coefficient (C) is a key parameter for the rational method, and typical C values are given and listed in various design manuals and textbooks for different land use conditions. Actually, these C values were developed without much support of observed data. This paper presents an in-depth literature review on the rational method and developed literature-based runoff coefficients estimated from land use data in 1992 and 2001 for 90 watersheds in central Texas. There is no statistically significant change on C values derived from two land use data. Runoff coefficients were also estimated from observed rainfall and runoff data of more than 1600 events in these watersheds. Distributions of runoff coefficients and watershed mean values are analyzed. Using watershed parameters (e.g., drainage area, slope, and channel length) and regression equations of discharge at different return periods we estimated runoff coefficients in these watersheds for the return periods of 2-, 5-, 10-, 25-, 50-, and 100-years. The rational runoff coefficients increase with the return period and the rate of increase is much larger than what typically recommended in design manuals.
- 12 May 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Water Subdivision for Modeling
Rainfall-Runoff models, such as Hydrologic Modeling System (HEC-HMS), Stormwater Management Model (SWMM), etc., are used for predicting the hydrologic response of watersheds. An issue that to be addressed by users of these models is the estimate of an appropriate level of watershed subdivision for simulating runoff. The size and number of subwatersheds can affect a watershed modeling process and subsequent results. The research reported herein is exploration to evaluate the effect of various levels of watershed subdivision on simulated runoff hydrographs. The HEC-HMS program was applied to five watersheds in Central Texas with drainage areas that varied from 12.3 to 166 square miles. Each of the five watersheds is near one of the following urban areas: Austin, Dallas (the rural watershed studied is close to Dallas), Fort Worth, San Antonio. In this study, the models were intentionally left uncalibrated, thus the subdivision specification is the result of application of engineering hydrologic modeling practice, as would occur when modeling ungaged watersheds. Watershed subdivision was performed using an iso-area arrpoach where each contributing subdivision contained roughly the same area. The results of the HEC-HMS analysis indicated that the number of subwatersheds had little effect on computed runoff hydrographs. No consistent pattern emerged as to whether lumped or multiple subbasins produce superior results; thus, the appropriate level of subdividing a watershed is still unanswered by this study.
- 12 May 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Water Subdivision for Modeling
Rainfall-Runoff models, such as Hydrologic Modeling System (HEC-HMS), Stormwater Management Model (SWMM), etc., are used for predicting the hydrologic response of watersheds. An issue that to be addressed by users of these models is the estimate of an appropriate level of watershed subdivision for simulating runoff. The size and number of subwatersheds can affect a watershed modeling process and subsequent results. The research reported herein is exploration to evaluate the effect of various levels of watershed subdivision on simulated runoff hydrographs. The HEC-HMS program was applied to five watersheds in Central Texas with drainage areas that varied from 12.3 to 166 square miles. Each of the five watersheds is near one of the following urban areas: Austin, Dallas (the rural watershed studied is close to Dallas), Fort Worth, San Antonio. In this study, the models were intentionally left uncalibrated, thus the subdivision specification is the result of application of engineering hydrologic modeling practice, as would occur when modeling ungaged watersheds. Watershed subdivision was performed using an iso-area arrpoach where each contributing subdivision contained roughly the same area. The results of the HEC-HMS analysis indicated that the number of subwatersheds had little effect on computed runoff hydrographs. No consistent pattern emerged as to whether lumped or multiple subbasins produce superior results; thus, the appropriate level of subdividing a watershed is still unanswered by this study.
- 12 May 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Use of the Basin Development Factor to Evaluate Urban Watershed Response
The Basin Development Factor (BDF) is a reasonably straightforward categorical variable that has promise for estimating urban hydrologic response. The objective of this study is exploratory — the goal is to learn whether the BDF improves the explanation of the rainfall and runoff responses of watersheds. This particular metric is attractive as an alternative to other metrics in use. The BDF was determined for more than 100 watersheds in Texas and then used to generate estimates of unit hydrograph timing characteristics and peak discharge characteristics. Simulated responses using these values are compared to both observed and prior simulated responses for the same watersheds. Inclusion of BDF as an explanatory variable in the regression analyses in this study to generate hydrologic responses did not materially reduce, or enhance performance in models of selected watersheds. This finding indicates that use of BDF cannot make estimates worse, but does not improve estimates either (and thus BDF as implemented here could be ignored). The result was discouraging, but the particular effort overlooked that the regression models used could estimate zero discharges, when, in fact, the actual database did not contain zero values. Despite the discouraging result, the authors believe that the BDF bears further study and suggestions for such studies are offered.
- 12 May 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Use of the Basin Development Factor to Evaluate Urban Watershed Response
The Basin Development Factor (BDF) is a reasonably straightforward categorical variable that has promise for estimating urban hydrologic response. The objective of this study is exploratory — the goal is to learn whether the BDF improves the explanation of the rainfall and runoff responses of watersheds. This particular metric is attractive as an alternative to other metrics in use. The BDF was determined for more than 100 watersheds in Texas and then used to generate estimates of unit hydrograph timing characteristics and peak discharge characteristics. Simulated responses using these values are compared to both observed and prior simulated responses for the same watersheds. Inclusion of BDF as an explanatory variable in the regression analyses in this study to generate hydrologic responses did not materially reduce, or enhance performance in models of selected watersheds. This finding indicates that use of BDF cannot make estimates worse, but does not improve estimates either (and thus BDF as implemented here could be ignored). The result was discouraging, but the particular effort overlooked that the regression models used could estimate zero discharges, when, in fact, the actual database did not contain zero values. Despite the discouraging result, the authors believe that the BDF bears further study and suggestions for such studies are offered.