Jan Šulc
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jan Šulc has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Zbyněk Zachoval
Faculty of Civil Engineering, Brno University of Technology, Veveří street 331/95, 602 00 Brno
2 shared publications - Jana Pařílková
Brno University of Technology, Department of Water Structures, Veveri 95, 60200, Brno, Czech Republic
1 shared publication - Jaromír Příhoda
Institute of Thermomechanics AS CR, v.v.i., Dolejškova 5, 182 00 Praha 8, Czech Republic
1 shared publication - Ján Rumann
Department of Hydraulic Engineering, Faculty of Civil Engineering, Slovak University of Technology in Bratislava, Bratislava, Slovakia
1 shared publication - Ladislav Roušar
Department of Water Structures, Faculty of Civil Engineering, Brno University of Technology, Veveří 331/95, 602 00, Brno, Czech Republic
1 shared publication - Michaela Knéblová
Department of Water management Conceptions and Information, Odra River Board, Varenská 49, 701 26, Ostrava, Czech Republic
1 shared publication
Latest Publications
- Open Access
- 4 April 2014
- Published by Walter de Gruyter GmbH in Journal of Hydrology and Hydromechanics
- Vol. 62 (2) , 145-149
Discharge coefficient of a rectangular sharp-edged broad-crested weir
This paper is concerned with the determination of the relationship for the calculation of the discharge coefficient at free overflow over a rectangular sharp-edged broad-crested weir without lateral contraction. The determination was made on the basis of new measurement in a range of the relative thickness of the weir from 0.12 to 0.30 and newly in a large range of relative height of the weir extremely from 0.24 to 6.8 which greatly expands the application possibilities of low weirs. In addition, the effects of friction and surface tension on the value of the discharge coefficient were evaluated as well as the effect of the relative thickness of the weir. The new equation for discharge coefficient, expressed using the relative height of the weir, was subjected to verification made by an independent laboratory which confirmed its accuracy.
- 4 April 2014
- Published by Walter de Gruyter GmbH in Journal of Hydrology and Hydromechanics
- Vol. 62 (2) , 145-149
Open AccessDischarge coefficient of a rectangular sharp-edged broad-crested weir
This paper is concerned with the determination of the relationship for the calculation of the discharge coefficient at free overflow over a rectangular sharp-edged broad-crested weir without lateral contraction. The determination was made on the basis of new measurement in a range of the relative thickness of the weir from 0.12 to 0.30 and newly in a large range of relative height of the weir extremely from 0.24 to 6.8 which greatly expands the application possibilities of low weirs. In addition, the effects of friction and surface tension on the value of the discharge coefficient were evaluated as well as the effect of the relative thickness of the weir. The new equation for discharge coefficient, expressed using the relative height of the weir, was subjected to verification made by an independent laboratory which confirmed its accuracy.
- Open Access
- 1 September 2013
- Published by Walter de Gruyter GmbH in Journal of Hydrology and Hydromechanics
- Vol. 61 (3) , 222-231
Shape of the Nappe During Free Overfall from a Rectangular Channel with Zero Bed Slope
The paper deals with selected procedures used to calculate the shape of compact nappe during free overfall from a smooth horizontal channel with rectangular cross section. Calculated and measured water surface and velocity conditions in the end section, the level of water surface upstream in front of the end section and the shape of the compact part of an overfall nappe are described for a particular compared case.
- 1 September 2013
- Published by Walter de Gruyter GmbH in Journal of Hydrology and Hydromechanics
- Vol. 61 (3) , 222-231
Open AccessShape of the Nappe During Free Overfall from a Rectangular Channel with Zero Bed Slope
The paper deals with selected procedures used to calculate the shape of compact nappe during free overfall from a smooth horizontal channel with rectangular cross section. Calculated and measured water surface and velocity conditions in the end section, the level of water surface upstream in front of the end section and the shape of the compact part of an overfall nappe are described for a particular compared case.
- Open Access
- 16 April 2012
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 25, 02023
Modelling of subcritical free-surface flow over an inclined backward-facing step in a water channel
- 16 April 2012
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 25, 02023
Open AccessModelling of subcritical free-surface flow over an inclined backward-facing step in a water channel