D. B. Knorr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
D. B. Knorr has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
T.-M. Lu
Rensselaer Polytechnic Institute
4 shared publicationsE. J. Rymaszewski
Rensselaer Polytechnic Institute
3 shared publicationsS. Cochrane
Rensselaer Polytech. Inst., Troy, NY, USA
2 shared publicationsW.-T. Liu
Center for Integrated Electronics, Rensselaer Polytechnic Institute, Troy, New York 12180-3590
2 shared publicationsE.J. Rymaszewski
1 shared publicationH. Bakhru
Department of Physics, State University of New York at Albany, Albany, New York 12222
1 shared publication
Latest Publications
- 1 September 1998
- Published by Springer Nature in Journal of Materials Science
- Vol. 33 (17) , 4375-4379
Discrete β-Ta2O5 crystallite formation in reactively sputtered amorphous thin films
- 1 September 1998
- Published by Springer Nature in Journal of Materials Science
- Vol. 33 (17) , 4375-4379
Discrete β-Ta2O5 crystallite formation in reactively sputtered amorphous thin films
- 13 February 1995
- Published by AIP Publishing in Applied Physics Letters
- Vol. 66 (7) , 809-811
Thermally stable amorphous BaxTi2−xOy thin films
The reactive partially ionized beam deposition technique was used to deposit amorphous BaxTi2−xOy thin films with the Ba/Ti ratios from 1 for a stoichiometric BaTiO3 film to 0.2 for a Ti enriched film. A postdeposition annealing between 500 and 600 °C converted stoichiometric amorphous BaTiO3 into polycrystalline structure. This crystallization resulted in densification with a 9% decrease in film thickness. Off‐stoichiometric thin films remained amorphous up to 700 °C. Annealed off‐stoichiometric BaxTi2−xOy films, however, had lower leakage current and loss tangent than polycrystalline films due to their amorphous nature making them more suitable for electronic applications. At temperatures of 800 °C or higher, significant reaction occurred between the films and Si substrate as detected by Rutherford backscattered spectroscopy.
- 13 February 1995
- Published by AIP Publishing in Applied Physics Letters
- Vol. 66 (7) , 809-811
Thermally stable amorphous BaxTi2−xOy thin films
The reactive partially ionized beam deposition technique was used to deposit amorphous BaxTi2−xOy thin films with the Ba/Ti ratios from 1 for a stoichiometric BaTiO3 film to 0.2 for a Ti enriched film. A postdeposition annealing between 500 and 600 °C converted stoichiometric amorphous BaTiO3 into polycrystalline structure. This crystallization resulted in densification with a 9% decrease in film thickness. Off‐stoichiometric thin films remained amorphous up to 700 °C. Annealed off‐stoichiometric BaxTi2−xOy films, however, had lower leakage current and loss tangent than polycrystalline films due to their amorphous nature making them more suitable for electronic applications. At temperatures of 800 °C or higher, significant reaction occurred between the films and Si substrate as detected by Rutherford backscattered spectroscopy.
- 1 July 1993
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 14 (7) , 320-322
Low-temperature fabrication of amorphous BaTiO/sub 3/ thin-film bypass capacitors
Amorphous BaTiO/sub 3/ thin-film capacitors suitable for integration into a multichip module packaging process were fabricated. The multilayer capacitor structure consisted of an adhesion layer (TiO/sub x/N/sub y/ or Ti), a bottom electrode (Cu), a dielectric (amorphous BaTiO/sub 3/), and a top electrode (Cu). A 3000-AA amorphous BaTiO/sub 3/ film was deposited onto the electrode by the reactive partially ionized beam (RPIB) technique at near room temperature. After a 300 degrees C postdeposition anneal, the capacitors had the following properties: epsilon /sub r/=17-18 and tan delta
- 1 July 1993
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 14 (7) , 320-322
Low-temperature fabrication of amorphous BaTiO/sub 3/ thin-film bypass capacitors
Amorphous BaTiO/sub 3/ thin-film capacitors suitable for integration into a multichip module packaging process were fabricated. The multilayer capacitor structure consisted of an adhesion layer (TiO/sub x/N/sub y/ or Ti), a bottom electrode (Cu), a dielectric (amorphous BaTiO/sub 3/), and a top electrode (Cu). A 3000-AA amorphous BaTiO/sub 3/ film was deposited onto the electrode by the reactive partially ionized beam (RPIB) technique at near room temperature. After a 300 degrees C postdeposition anneal, the capacitors had the following properties: epsilon /sub r/=17-18 and tan delta
- 1 January 1993
- Published by Springer Nature in MRS Proceedings
- Vol. 310
Deposition, Structural Characterization, and Broadband (1KHz-40GHz) Dielectric Behavior of BaxTi2-xOy Thin Films
- 1 January 1993
- Published by Springer Nature in MRS Proceedings
- Vol. 310
Deposition, Structural Characterization, and Broadband (1KHz-40GHz) Dielectric Behavior of BaxTi2-xOy Thin Films