Keiji Ogi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Keiji Ogi has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Koichi Mizukami
Graduate School of Science and Engineering, Ehime University, 3 Bunkyo-cho, Matsuyama, Ehime, Japan
7 shared publications - Shigeki Yashiro
Department of Aeronautics and Astronautics, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
3 shared publications Ryotaro Ozaki
2 shared publicationsShigeki Yashiro
2 shared publications- Shinya Matsuda
Area in Advanced Materials Science, Department of Engineering and Design, Faculty of Engineering and Design Kagawa University Takamatsu Kagawa Japan
2 shared publications Baso Nasrullah
1 shared publication
Latest Publications
- Open Access
- 14 May 2026
- Published by Elsevier in Composite Structures
- Vol. 389
Octahedral fiber-composite inertial amplification metamaterials for broadband attenuation of three-dimensional vibrations
- 14 May 2026
- Published by Elsevier in Composite Structures
- Vol. 389
Open AccessOctahedral fiber-composite inertial amplification metamaterials for broadband attenuation of three-dimensional vibrations
- 13 September 2025
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 200
A damage tensor-based model for effective resistivity of CFRP θ 1 / θ 2 S laminates with matrix cracking
- 13 September 2025
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 200
A damage tensor-based model for effective resistivity of CFRP θ 1 / θ 2 S laminates with matrix cracking
- Open Access
- 26 July 2025
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 618
3D-printed fiber-steered acoustic black hole beam for enhanced damping in low-frequency range
- 26 July 2025
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 618
Open Access3D-printed fiber-steered acoustic black hole beam for enhanced damping in low-frequency range
- 11 July 2024
- Published by Elsevier in Mechanics of Materials
- Vol. 197
Prediction of viscoelastic effective creep compliances in cracked cross-ply composite laminates
- 11 July 2024
- Published by Elsevier in Mechanics of Materials
- Vol. 197
Prediction of viscoelastic effective creep compliances in cracked cross-ply composite laminates
- 11 March 2024
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 580
Fiber-steered acoustic black hole beam with low cut-on frequency and high stiffness
- 11 March 2024
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 580
Fiber-steered acoustic black hole beam with low cut-on frequency and high stiffness
- 14 October 2023
- Published by Elsevier in Composite Structures
- Vol. 326, 117626
Analytical modeling and 3D printing of locally resonant composite sandwich metamaterials with inertial amplification mechanisms
- 14 October 2023
- Published by Elsevier in Composite Structures
- Vol. 326, 117626
Analytical modeling and 3D printing of locally resonant composite sandwich metamaterials with inertial amplification mechanisms
- 24 August 2021
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 55 (28) , 4111-4124
Characterization of piercing damage in CFRP cross-ply laminates after punch shear machining via impact loading
In industrial processes, piercing and trimming are essential because composite structures are usually manufactured in a near-net shape to reduce machining operations. Punching and shear cutting using out-of-plane shear loading are expected to increase productivity. Nevertheless, little is known about the effects of such operations on polymer-matrix composites. This study presents on the characterization of piercing damage in typical carbon fiber reinforced plastic (CFRP) cross-ply laminates [0°2/90°2]s after punching using quasi-static (QS) and drop-weight impact (DWI) loadings. During QS punching, the upper and lower ply interfaces delaminate due to the high shear stress to cut fibers and gradual shear deformation in the middle ply; however, during DWI punching at a low impact velocity, delamination of the lower ply interface can be reduced due to the localization of shear deformation, as compared to that in QS punching. Finally, the damage accumulation process during DWI punching is discussed.
- 24 August 2021
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 55 (28) , 4111-4124
Characterization of piercing damage in CFRP cross-ply laminates after punch shear machining via impact loading
In industrial processes, piercing and trimming are essential because composite structures are usually manufactured in a near-net shape to reduce machining operations. Punching and shear cutting using out-of-plane shear loading are expected to increase productivity. Nevertheless, little is known about the effects of such operations on polymer-matrix composites. This study presents on the characterization of piercing damage in typical carbon fiber reinforced plastic (CFRP) cross-ply laminates [0°2/90°2]s after punching using quasi-static (QS) and drop-weight impact (DWI) loadings. During QS punching, the upper and lower ply interfaces delaminate due to the high shear stress to cut fibers and gradual shear deformation in the middle ply; however, during DWI punching at a low impact velocity, delamination of the lower ply interface can be reduced due to the localization of shear deformation, as compared to that in QS punching. Finally, the damage accumulation process during DWI punching is discussed.