Patrick Bourgin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Patrick Bourgin has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- M'HAmed Boutaous
Université de Lyon, CNRS, INSA-Lyon, CETHIL, UMR5008, F-69621, Villeurbanne, France
4 shared publications - M'Hamed Boutaous
Université Louis Pasteur, Institut de Mécanique des Fluides, 2, rue Boussingault — 67000, Strasbourg, France
1 shared publication Matthieu Zinet
Universite´ de Lyon, Villeurbanne, France
1 shared publicationM’hamed Boutaous
Ecole Supe´rieure de Plasturgie, 85 rue Henri Becquerel, B.P. 801—01108 Oyonnax, France
1 shared publicationNadia Brahmia
1 shared publication- Rabie El Otmani
Science Engineer Laboratory for Energy (LabSIPE) at National School of Applied Sciences, Chouaib Doukkali University, EL Jadida, Morocco
1 shared publication
Latest Publications
- 28 February 2010
- Published by MathDoc/Centre Mersenne in Comptes Rendus Mécanique
- Vol. 338 (2) , 78-84
Parametric study of the crystallization kinetics of a semi-crystalline polymer during cooling
International audienceDuring the cooling stage in several types polymer processing, the behavior of the polymer is very difficult to model and to simulate numerically, because of the complicated coupling between the crystallization process, the heat transfer and the material properties change. The aim of this Note is the numerical simulation of the coupling phenomena between the crystallization rate and the thermal kinetics in a semi-crystalline polymer during cooling without flow, by using Finite Elements Method
- 28 February 2010
- Published by MathDoc/Centre Mersenne in Comptes Rendus Mécanique
- Vol. 338 (2) , 78-84
Parametric study of the crystallization kinetics of a semi-crystalline polymer during cooling
International audienceDuring the cooling stage in several types polymer processing, the behavior of the polymer is very difficult to model and to simulate numerically, because of the complicated coupling between the crystallization process, the heat transfer and the material properties change. The aim of this Note is the numerical simulation of the coupling phenomena between the crystallization rate and the thermal kinetics in a semi-crystalline polymer during cooling without flow, by using Finite Elements Method
- 1 January 2010
- Published by ASME International
- p. 1393-1400
Simulation of Polymer Crystallization: Role of the Visco-Elasticity
In polymer processing, it is established that the flow causes the polymer chains to stretch and store the energy, by changing their quiescent state free energy. Koscher et al. [1] presented in 2002 an experimental work concerning the flow induced crystallization. They made the assumption that the polymer melt elasticity, quantified by the first normal stress difference, is the driving force of flow-induced extra nucleation. In their work, a constant shear stress is considered, and the first normal stress difference agrees with the use of the trace of the stress tensor. The stored energy due to the flow “Δ Ge” is commonly called elastic free energy and associated to the change in conformational tensor due to flow. By extending the Marrucci theory [2], several studies link this Δ Ge to the trace of the deviatoric stress tensor (first invariant). In this paper, a numerical model able to simulate polymer crystallization is developed. It is based on the assumption that flow induced extra nucleation is linked to the trace of the deviatoric stress tensor. Thus a viscoelastic constitutive equation, the multimode Upper Convected Maxwell (UCM) model, is used to express the viscoelastic extra-stress tensor τVE, and a damping function is introduced in order to take into account the nonlinear viscoelasticity of the material. In Koscher’s work [1], the integral formulation of the Upper Convected Maxwell (UCM) model is used too, but without any damping function, i.e. they assume that the polymer behaves as linear viscoelastic. As an application, a 2D isothermal flow configuration between two plates is simulated. A comparison between the proposed model and the Koscher’s one is then performed, and interesting resultes are pesented: without introducing a damping function, the two models give similar results in the same configurations, but the introduction of a damping function leads to important discrepancies between the two models, seeming that the assumption of a linear viscoelastic behavior is not realistic when the fluid strain and/or stresses are greater than a given values.
- 1 January 2010
- Published by ASME International
- p. 1393-1400
Simulation of Polymer Crystallization: Role of the Visco-Elasticity
In polymer processing, it is established that the flow causes the polymer chains to stretch and store the energy, by changing their quiescent state free energy. Koscher et al. [1] presented in 2002 an experimental work concerning the flow induced crystallization. They made the assumption that the polymer melt elasticity, quantified by the first normal stress difference, is the driving force of flow-induced extra nucleation. In their work, a constant shear stress is considered, and the first normal stress difference agrees with the use of the trace of the stress tensor. The stored energy due to the flow “Δ Ge” is commonly called elastic free energy and associated to the change in conformational tensor due to flow. By extending the Marrucci theory [2], several studies link this Δ Ge to the trace of the deviatoric stress tensor (first invariant). In this paper, a numerical model able to simulate polymer crystallization is developed. It is based on the assumption that flow induced extra nucleation is linked to the trace of the deviatoric stress tensor. Thus a viscoelastic constitutive equation, the multimode Upper Convected Maxwell (UCM) model, is used to express the viscoelastic extra-stress tensor τVE, and a damping function is introduced in order to take into account the nonlinear viscoelasticity of the material. In Koscher’s work [1], the integral formulation of the Upper Convected Maxwell (UCM) model is used too, but without any damping function, i.e. they assume that the polymer behaves as linear viscoelastic. As an application, a 2D isothermal flow configuration between two plates is simulated. A comparison between the proposed model and the Koscher’s one is then performed, and interesting resultes are pesented: without introducing a damping function, the two models give similar results in the same configurations, but the introduction of a damping function leads to important discrepancies between the two models, seeming that the assumption of a linear viscoelastic behavior is not realistic when the fluid strain and/or stresses are greater than a given values.
- 1 March 2004
- Published by ASME International in Journal of Fluids Engineering
- Vol. 126 (2) , 216-222
Macroscopic Effects of Surface Roughness in Confined Air Flow
The general framework deals with the winding of thin plastic films, in order to obtain good-quality rolls. This issue is tightly connected to the thickness of the residual air layer entrapped between the film layers. It is then of importance to optimize the surface topography of the films so that to improve the quality of the wound rolls. In a previous work, we proposed a simple model for the flow of an air layer squeezed between a solid smooth substrate and a plastic film sample: it was shown experimentally that the macroscopic characteristics of the flow are connected to the film roughness, but how? In order to answer this question, we assimilated the confined air flow to a flow through a periodic array of cylinders and a mathematical model based on homogenization techniques was developed. In the present paper, we search for pertinent parameters which describe the real surface roughness of plastic films. The experiments were carried out by using a 3-D roughness measurement device and the first observation is that the roughness distribution is not uniform. We made a sampling expressed by the percentage of peaks exceeding some given height threshold. The corresponding experimental parameters are used to define the network of cylinders. For each type of film, the threshold value is the only adjustable parameter and the following results are obtained: It is possible to adjust this parameter so that to obtain a very good agreement between the experimental data and the theoretical predictions. In addition, the smoother the film, the more important the highest peaks are in terms of air leakage.
- 1 March 2004
- Published by ASME International in Journal of Fluids Engineering
- Vol. 126 (2) , 216-222
Macroscopic Effects of Surface Roughness in Confined Air Flow
The general framework deals with the winding of thin plastic films, in order to obtain good-quality rolls. This issue is tightly connected to the thickness of the residual air layer entrapped between the film layers. It is then of importance to optimize the surface topography of the films so that to improve the quality of the wound rolls. In a previous work, we proposed a simple model for the flow of an air layer squeezed between a solid smooth substrate and a plastic film sample: it was shown experimentally that the macroscopic characteristics of the flow are connected to the film roughness, but how? In order to answer this question, we assimilated the confined air flow to a flow through a periodic array of cylinders and a mathematical model based on homogenization techniques was developed. In the present paper, we search for pertinent parameters which describe the real surface roughness of plastic films. The experiments were carried out by using a 3-D roughness measurement device and the first observation is that the roughness distribution is not uniform. We made a sampling expressed by the percentage of peaks exceeding some given height threshold. The corresponding experimental parameters are used to define the network of cylinders. For each type of film, the threshold value is the only adjustable parameter and the following results are obtained: It is possible to adjust this parameter so that to obtain a very good agreement between the experimental data and the theoretical predictions. In addition, the smoother the film, the more important the highest peaks are in terms of air leakage.
- 1 January 2002
- Published by EDP Sciences in Matériaux & Techniques
- Vol. 90, 21-24
High velocity winding of plastic films : influence of suface topography on the air interlayers
One challenge when processing flexible media such as plastic films is to obtain rolls without any aspect defect : if one considers that a “defect” (i.e. wrinkling or buckling) is due to the fact that the stress generated within the roll is greater than some “plasticity yield”, then it is crucial to predict the internal stress state. Several process parameters must be carefully mastered. One important effect, though difficult to evaluate, is that of surface topography, and its influence on the roll quality. Several authors [1,2] assumed that the roll is a composite material, resulting from the accretion of circular film layers separated by air layers. It is suggested that the radial elastic modulus of the roll is a nonlinear function of the compressive stress, depending on the amount of air entrapped. This is an indirect way to take into account the influence of surface topography on the stress state generated within a roll wound at high speed. In this article, we propose to connect some pertinent static roughness parameters of plastic films to their dynamic effects. The main features of our experimental set-up are recalled, see [4] : it consists in an air layer squeezed between the rough flexible surface to be characterized (i.e. film sample) and a rigid smooth one (i.e. glass substrate). In order to establish a relationship between the thickness reduction of the air layer and the displacement of the front representing the air layer evacuation, a mathematical model has been developed [5]. This model is based on homogeneization techniques, considering that the flow domain (gap between the rough film and the substrate) is composed of a regular array of cylinders. The cylinders heights, radii and periods of spatial distribution are connected to the actual characteristics measured by a 3D roughness profilometer. The statistical data processing consists in selecting the peaks higher than some prescribed threshold. The corresponding parameters are introduced into the mathematical model. They represent respectively : cylinders heights, spacing between cylinders and diameters. The experimental data are compared to the theoretical predictions, for several values of the threshold, and an optimum value of the threshold is found. Résumé L'un des défis posés par l’enroulement des matériaux flexibles, comme par exemple les films plastiques, est d'obtenir des rouleaux exempts de défauts : si l’on considère qu’un défaut provient du fait que les contraintes générées au sein du rouleau dépassent un certain seuil de plasticité, alors ils est important de prévoir cet état de contrainte. De ce fait plusieurs paramètres doivent être maîtrisés. L’un des plus effets les plus importants et les plus difficiles à maîtriser est celui de la topographie de surface ainsi que son influence sur la qualité du rouleau. Différents auteurs [1,2] assimilent le rouleau à un matériau composite, résultant de l’accrétion de couches successives et circulaires de film, séparées par des couches d'air. Il a été suggéré que le module d'élasticité radiale du rouleau en fonction des contrainte d'écrasement est non- linéaire, et dépend de la quantité d’air interspire. C’est une façon indirecte de tenir compte de l’influence de la rugosité sur l'état de contrainte généré au sein du rouleau, lors de l’enroulement à grande vitesse. Dans cet article, nous nous proposons de mettre en évidence l'influence de quelques paramètres pertinents de rugosité statique de films plastiques sur la dynamique de l’écoulement d’air entre les couches du rouleau. Le dispositif expérimental est détaillé dans [4] : il consiste à écraser une couche d’air entre la feuille de film plastique rugueux à caractériser et un substrat lisse et rigide. Afin d’établir une relation entre la réduction de l’épaisseur de la couche d’air et le déplacement du front représentant son évacuation, un modèle mathématique est développé [5] Il repose sur les techniques d’homogénéisation périodique, en considérant que le domaine d’écoulement est composé d’un arrangement périodiques de cylindres. La hauteur de ces cylindres, leur rayon et la période de distribution spatiale sont directement liés aux caractéristiques réelles mesurées. L'étude statistique des mesures consiste ci sélectionner les pics dépassant une certaine valeur seuil choisie. Les paramètres correspondants sont introduits dans le modèle mathématique. Ils représentent respectivement les hauteurs, l’espacement entre cylindres et leur diamètre. Les mesures expérimentales et les résultats du modèle offrent un bon accord pour une valeur optimale du seuil.
- 1 January 2002
- Published by EDP Sciences in Matériaux & Techniques
- Vol. 90, 21-24
High velocity winding of plastic films : influence of suface topography on the air interlayers
One challenge when processing flexible media such as plastic films is to obtain rolls without any aspect defect : if one considers that a “defect” (i.e. wrinkling or buckling) is due to the fact that the stress generated within the roll is greater than some “plasticity yield”, then it is crucial to predict the internal stress state. Several process parameters must be carefully mastered. One important effect, though difficult to evaluate, is that of surface topography, and its influence on the roll quality. Several authors [1,2] assumed that the roll is a composite material, resulting from the accretion of circular film layers separated by air layers. It is suggested that the radial elastic modulus of the roll is a nonlinear function of the compressive stress, depending on the amount of air entrapped. This is an indirect way to take into account the influence of surface topography on the stress state generated within a roll wound at high speed. In this article, we propose to connect some pertinent static roughness parameters of plastic films to their dynamic effects. The main features of our experimental set-up are recalled, see [4] : it consists in an air layer squeezed between the rough flexible surface to be characterized (i.e. film sample) and a rigid smooth one (i.e. glass substrate). In order to establish a relationship between the thickness reduction of the air layer and the displacement of the front representing the air layer evacuation, a mathematical model has been developed [5]. This model is based on homogeneization techniques, considering that the flow domain (gap between the rough film and the substrate) is composed of a regular array of cylinders. The cylinders heights, radii and periods of spatial distribution are connected to the actual characteristics measured by a 3D roughness profilometer. The statistical data processing consists in selecting the peaks higher than some prescribed threshold. The corresponding parameters are introduced into the mathematical model. They represent respectively : cylinders heights, spacing between cylinders and diameters. The experimental data are compared to the theoretical predictions, for several values of the threshold, and an optimum value of the threshold is found. Résumé L'un des défis posés par l’enroulement des matériaux flexibles, comme par exemple les films plastiques, est d'obtenir des rouleaux exempts de défauts : si l’on considère qu’un défaut provient du fait que les contraintes générées au sein du rouleau dépassent un certain seuil de plasticité, alors ils est important de prévoir cet état de contrainte. De ce fait plusieurs paramètres doivent être maîtrisés. L’un des plus effets les plus importants et les plus difficiles à maîtriser est celui de la topographie de surface ainsi que son influence sur la qualité du rouleau. Différents auteurs [1,2] assimilent le rouleau à un matériau composite, résultant de l’accrétion de couches successives et circulaires de film, séparées par des couches d'air. Il a été suggéré que le module d'élasticité radiale du rouleau en fonction des contrainte d'écrasement est non- linéaire, et dépend de la quantité d’air interspire. C’est une façon indirecte de tenir compte de l’influence de la rugosité sur l'état de contrainte généré au sein du rouleau, lors de l’enroulement à grande vitesse. Dans cet article, nous nous proposons de mettre en évidence l'influence de quelques paramètres pertinents de rugosité statique de films plastiques sur la dynamique de l’écoulement d’air entre les couches du rouleau. Le dispositif expérimental est détaillé dans [4] : il consiste à écraser une couche d’air entre la feuille de film plastique rugueux à caractériser et un substrat lisse et rigide. Afin d’établir une relation entre la réduction de l’épaisseur de la couche d’air et le déplacement du front représentant son évacuation, un modèle mathématique est développé [5] Il repose sur les techniques d’homogénéisation périodique, en considérant que le domaine d’écoulement est composé d’un arrangement périodiques de cylindres. La hauteur de ces cylindres, leur rayon et la période de distribution spatiale sont directement liés aux caractéristiques réelles mesurées. L'étude statistique des mesures consiste ci sélectionner les pics dépassant une certaine valeur seuil choisie. Les paramètres correspondants sont introduits dans le modèle mathématique. Ils représentent respectivement les hauteurs, l’espacement entre cylindres et leur diamètre. Les mesures expérimentales et les résultats du modèle offrent un bon accord pour une valeur optimale du seuil.
- Open Access
- 1 January 2000
- Published by Society of Advanced Science in Journal of Advanced Science
- Vol. 12 (3) , 257-261
Intelligent winding of flexible media: Towards tailored surface topographies.
- 1 January 2000
- Published by Society of Advanced Science in Journal of Advanced Science
- Vol. 12 (3) , 257-261
Open AccessIntelligent winding of flexible media: Towards tailored surface topographies.
- 1 December 1999
- Published by Wiley in Macromolecular Symposia
- Vol. 148 (1) , 311-319
Dynamic characterization of surface topography of plastic films
- 1 December 1999
- Published by Wiley in Macromolecular Symposia
- Vol. 148 (1) , 311-319
Dynamic characterization of surface topography of plastic films