Fabio Gori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Fabio Gori has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Boghi
School of Water, Energy and Agrifood, Cranfield University, Cranfield, Bedfordshire, UK
5 shared publications A. Doro Altan
University of Rome “Tor Vergata
2 shared publications- Ivan Di Venuta
Department of Industrial Engineering, University of Rome “Tor Vergata,” Rome, Italy
2 shared publications - Ivano Petracci
Department of Industrial Engineering, University of Rome Tor Vergata, Rome, Italy
2 shared publications - Matteo Angelino
Loughborough University
2 shared publications D. Carnevale
University of Rome “Tor Vergata
1 shared publication
Latest Publications
- Open Access
- 27 April 2024
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 155
Universal thermal profiles with polynomial thermal diffusivity in a channel flow
- 27 April 2024
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 155
Open AccessUniversal thermal profiles with polynomial thermal diffusivity in a channel flow
- 11 April 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 138, 41-48
Effect of structure, porosity, saturating fluid and solid material on the effective thermal conductivity of open-cells foams
- 11 April 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 138, 41-48
Effect of structure, porosity, saturating fluid and solid material on the effective thermal conductivity of open-cells foams
- 29 August 2017
- Published by Wiley in Journal of Heat Transfer
- Vol. 140 (2)
Lateral Edge Effects on the Sherwood Number in Turbulent Flow Over a Flat Plate
Experimental results for the Sherwood number variation near the lateral edge of the active surface of a smooth, finite-width flat plate in turbulent boundary layer flow are presented. Using naphthalene sublimation, local mass transfer rates are found for two different free stream velocities. A semi-empirical correlation of the experimental data is presented, allowing calculation of the increase of mass transfer near the edge and the size of the region affected by the lateral edge. The effect is shown to scale more so with the diffusion thickness than the boundary layer thickness.
- 29 August 2017
- Published by Wiley in Journal of Heat Transfer
- Vol. 140 (2)
Lateral Edge Effects on the Sherwood Number in Turbulent Flow Over a Flat Plate
Experimental results for the Sherwood number variation near the lateral edge of the active surface of a smooth, finite-width flat plate in turbulent boundary layer flow are presented. Using naphthalene sublimation, local mass transfer rates are found for two different free stream velocities. A semi-empirical correlation of the experimental data is presented, allowing calculation of the increase of mass transfer near the edge and the size of the region affected by the lateral edge. The effect is shown to scale more so with the diffusion thickness than the boundary layer thickness.
- Open Access
- 19 March 2017
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 71 (6) , 638-652
Three-dimensional numerical simulation of a failed coronary stent implant at different degrees of residual stenosis. Part I: Fluid dynamics and shear stress on the vascular wall
The influence of the degree of residual stenosis on the hemodynamics inside coronary arteries is investigated through three-dimensional (3D) numerical simulations. The present paper, which is the first of a series of two, focuses on the influence that the degree of residual stenosis (DOR) has on the fluid dynamics and the shear stresses acting on the stent and the artery wall. The pulsatile nature of the blood flow and its non-Newtonian features are taken into account. Four models of artery are investigated. The results show that the wall shear stress (WSS) increases monotonically, but not linearly, with the DOR.
- 19 March 2017
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 71 (6) , 638-652
Open AccessThree-dimensional numerical simulation of a failed coronary stent implant at different degrees of residual stenosis. Part I: Fluid dynamics and shear stress on the vascular wall
The influence of the degree of residual stenosis on the hemodynamics inside coronary arteries is investigated through three-dimensional (3D) numerical simulations. The present paper, which is the first of a series of two, focuses on the influence that the degree of residual stenosis (DOR) has on the fluid dynamics and the shear stresses acting on the stent and the artery wall. The pulsatile nature of the blood flow and its non-Newtonian features are taken into account. Four models of artery are investigated. The results show that the wall shear stress (WSS) increases monotonically, but not linearly, with the DOR.
- 19 March 2017
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 71 (6) , 653-665
Three-dimensional numerical simulation of a failed coronary stent implant at different degrees of residual stenosis. Part II: Apparent viscosity and wall permeability
The influence of the degree of residual stenosis (DOR) on the hemodynamics inside coronary arteries is investigated through three-dimensional (3D) numerical simulations. The vascular wall permeability is investigated and the effect of the non-Newtonian viscosity discussed. The results agree in predicting an abrupt increase in wall permeability above 45% DOR, indicating that the implant could lead to a massive restenosis. This behavior is considered to be due to the shift of the regions involved by low and oscillatory wall shear stress (WSS), from the zone adjacent to the struts toward the center of the stent meshes.
- 19 March 2017
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 71 (6) , 653-665
Three-dimensional numerical simulation of a failed coronary stent implant at different degrees of residual stenosis. Part II: Apparent viscosity and wall permeability
The influence of the degree of residual stenosis (DOR) on the hemodynamics inside coronary arteries is investigated through three-dimensional (3D) numerical simulations. The vascular wall permeability is investigated and the effect of the non-Newtonian viscosity discussed. The results agree in predicting an abrupt increase in wall permeability above 45% DOR, indicating that the implant could lead to a massive restenosis. This behavior is considered to be due to the shift of the regions involved by low and oscillatory wall shear stress (WSS), from the zone adjacent to the struts toward the center of the stent meshes.
- Open Access
- 20 September 2016
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 70 (8) , 815-830
Numerical solution of three-dimensional rectangular submerged jets with the evidence of the undisturbed region of flow
The evolution of turbulent rectangular submerged free jets has been investigated numerically with a two-dimensional (2D) approach by the present authors and, by using the large eddy simulations (LES) at several Reynolds numbers. The average numerical results confirmed the presence of the undisturbed region of flow (URF) located between the slot exit and the beginning of the potential core region (PCR) previously observed experimentally at the University of Rome “Tor Vergata” by Gori and coworkers. The 2D study of the present authors carried out under the conditions previously investigated in the literature, showed that the URF has a self-similar behavior, and proposed a new law for the evolution of the momentum. The present paper extends the LES to three-dimensional (3D) rectangular submerged free jets, in the range from Re = 5,000 to Re = 40,000, showing that the self-similar behavior of URF is also present in the 3D numerical simulations, as well as in the PCR and in the fully developed region (FDR).
- 20 September 2016
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 70 (8) , 815-830
Open AccessNumerical solution of three-dimensional rectangular submerged jets with the evidence of the undisturbed region of flow
The evolution of turbulent rectangular submerged free jets has been investigated numerically with a two-dimensional (2D) approach by the present authors and, by using the large eddy simulations (LES) at several Reynolds numbers. The average numerical results confirmed the presence of the undisturbed region of flow (URF) located between the slot exit and the beginning of the potential core region (PCR) previously observed experimentally at the University of Rome “Tor Vergata” by Gori and coworkers. The 2D study of the present authors carried out under the conditions previously investigated in the literature, showed that the URF has a self-similar behavior, and proposed a new law for the evolution of the momentum. The present paper extends the LES to three-dimensional (3D) rectangular submerged free jets, in the range from Re = 5,000 to Re = 40,000, showing that the self-similar behavior of URF is also present in the 3D numerical simulations, as well as in the PCR and in the fully developed region (FDR).
- 1 June 2016
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 104, 54-67
Numerical simulation of the optimal spacing for a radial finned tube cooled by a rectangular jet. I – Average thermal results
- 1 June 2016
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 104, 54-67
Numerical simulation of the optimal spacing for a radial finned tube cooled by a rectangular jet. I – Average thermal results
- 22 April 2015
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 68 (3) , 225-242
Numerical Simulation of Blood Flow through Different Stents in Stenosed and Non-Stenosed Vessels
Fluid dynamics in two different stent configurations, peak-to-valley (S1) and peak-to-peak (S2), within a fully expanded situation and a 30% restenosis is investigated. Numerical simulations are carried out in order to evaluate the conditions promoting atherosclerotic events when a self-expanding bare metal stent is applied. The conclusions are that the two configurations, S1 and S2, have a similar fluid dynamics behavior as far as wall shear stress is concerned, but oscillatory shear and relative residence time maps suggest that the peak-to-peak configuration, S2, has a better behavior than the peak-to-valley, S1.
- 22 April 2015
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 68 (3) , 225-242
Numerical Simulation of Blood Flow through Different Stents in Stenosed and Non-Stenosed Vessels
Fluid dynamics in two different stent configurations, peak-to-valley (S1) and peak-to-peak (S2), within a fully expanded situation and a 30% restenosis is investigated. Numerical simulations are carried out in order to evaluate the conditions promoting atherosclerotic events when a self-expanding bare metal stent is applied. The conclusions are that the two configurations, S1 and S2, have a similar fluid dynamics behavior as far as wall shear stress is concerned, but oscillatory shear and relative residence time maps suggest that the peak-to-peak configuration, S2, has a better behavior than the peak-to-valley, S1.
- 9 November 2012
- Published by ASME International
- p. 2679-2688
Experimental and Numerical Heat Transfer on a Cylinder Cooled by Two Rectangular Jets of Different Heights
The present paper presents experimental measurements of heat transfer on a cylinder, cooled by two rectangular jets of the same width but different height, H, in order to investigate the influence of the jet height on the local and the average cooling rates, because one of the problems in the heat transfer with jet flow is the convenience to choose the height of the jet in comparison to the height of the impinged object. The cylinder, heated by electric current, is set at several distances from the jet exit, x, on the symmetrical plane of symmetry, i.e. in a two-dimensional geometry, in order to find the optimal position which realizes the maximum heat transfer. The experimental heat transfer on the impingement shows that the local Nusselt number, defined with the cylinder diameter, D, is greater for the smaller slot because velocity is slightly higher but the average Nusselt numbers, defined with the cylinder diameter, D, are quite similar because the higher slot has a greater surface of impingement. Local and average Nusselt numbers are in qualitative agreement only if are compared with the same dimensionless distance, x/H, which can be interpreted as the ratio Rex/ReH, which is per unit of mass flow rate or is independent of the mass flow rate. Numerical simulations are carried out with a two-equations turbulent model using the RNG k-ε approach, on a cylinder with the same thickness of the experiments or without thickness. The numerical simulations of the cylinder without thickness are in acceptable agreement for what concern the average Nusselt numbers. The local Nusselt numbers are in fair agreement only if the cylinder has the thickness of the experiments, independently of the heat flow conditions, i.e. uniformly throughout the thickness or from the inner surface.
- 9 November 2012
- Published by ASME International
- p. 2679-2688
Experimental and Numerical Heat Transfer on a Cylinder Cooled by Two Rectangular Jets of Different Heights
The present paper presents experimental measurements of heat transfer on a cylinder, cooled by two rectangular jets of the same width but different height, H, in order to investigate the influence of the jet height on the local and the average cooling rates, because one of the problems in the heat transfer with jet flow is the convenience to choose the height of the jet in comparison to the height of the impinged object. The cylinder, heated by electric current, is set at several distances from the jet exit, x, on the symmetrical plane of symmetry, i.e. in a two-dimensional geometry, in order to find the optimal position which realizes the maximum heat transfer. The experimental heat transfer on the impingement shows that the local Nusselt number, defined with the cylinder diameter, D, is greater for the smaller slot because velocity is slightly higher but the average Nusselt numbers, defined with the cylinder diameter, D, are quite similar because the higher slot has a greater surface of impingement. Local and average Nusselt numbers are in qualitative agreement only if are compared with the same dimensionless distance, x/H, which can be interpreted as the ratio Rex/ReH, which is per unit of mass flow rate or is independent of the mass flow rate. Numerical simulations are carried out with a two-equations turbulent model using the RNG k-ε approach, on a cylinder with the same thickness of the experiments or without thickness. The numerical simulations of the cylinder without thickness are in acceptable agreement for what concern the average Nusselt numbers. The local Nusselt numbers are in fair agreement only if the cylinder has the thickness of the experiments, independently of the heat flow conditions, i.e. uniformly throughout the thickness or from the inner surface.
- 1 December 2008
- Published by Elsevier in Applied Thermal Engineering
- Vol. 28 (17-18) , 2159-2166
Transient thermal analysis of Vega launcher structures
- 1 December 2008
- Published by Elsevier in Applied Thermal Engineering
- Vol. 28 (17-18) , 2159-2166
Transient thermal analysis of Vega launcher structures