Ivano Petracci
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ivano Petracci has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Sandra Corasaniti
Department of Industrial Engineering, University of Rome Tor Vergata, 00133 Rome, Italy
5 shared publications - Michele Potenza
Department of Industrial Engineering, University of Rome “Tor Vergata”, Via del Politecnico 1, 00133 Rome, Italy
3 shared publications - Fabio Gori
Department of Industrial Engineering, University of Rome “Tor Vergata,” Rome, Italy
2 shared publications - Luca Manni
Department of Industrial Engineering, University of Rome “Tor Vergata”, Via del Politecnico n.1, 00133 Rome, Italy
2 shared publications - Alessandro Quintino
Department of Electrical and Energy Engineering (DIEE), Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
1 shared publication - Ateeq Ur Rehman
Department of Industrial Engineering, University of Rome Tor Vergata, 00133 Rome, Italy
1 shared publication
Latest Publications
- 21 March 2026
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 47 (4) , 66
Numerical and Machine Learning Methods to Predict the Thermal Behaviour of New Photovoltaic Cells in Order to Increase Their Efficiency
- 21 March 2026
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 47 (4) , 66
Numerical and Machine Learning Methods to Predict the Thermal Behaviour of New Photovoltaic Cells in Order to Increase Their Efficiency
- Open Access
- 1 January 2026
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 13 (1) , 01-13
Numerical Investigation of Porosity Effects on the Thermo-Hydraulic Performance of a Kagome-Lattice Duct in a Conjugate Problem
The Volume 12, published for JFFHMT Journal.
- 1 January 2026
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 13 (1) , 01-13
Open AccessNumerical Investigation of Porosity Effects on the Thermo-Hydraulic Performance of a Kagome-Lattice Duct in a Conjugate Problem
The Volume 12, published for JFFHMT Journal.
- 6 January 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 240
Thermo-fluid dynamic behaviour of a small length 3D printed lattice channel in a conjugated problem
- 6 January 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 240
Thermo-fluid dynamic behaviour of a small length 3D printed lattice channel in a conjugated problem
- Open Access
Steady- and Transient-State CFD Simulations of a Modified Barra–Costantini Solar System in Comparison with a Traditional Trombe–Michel Wall
Passive solar systems are one of most important strategies to reduce the heating loads of buildings. The Trombe–Michel (TM) wall and its variants are some of the better-known structures in the field of solar systems. An alternative to the TM wall is the Barra–Costantini (BC) system. In the present paper, CFD numerical simulations, both in steady and transient states, of modified BC and TM walls were carried out in the winter season. Different interspace thicknesses were simulated in order to evaluate their effects on the temperature field and air velocity, and the numerical results were compared among them. It was found that the BC system offers greater hot air flow compared with the TM wall; the mass flow rate increased up to 43% in the BC system and up 28% in the TM system when the interlayer thickness was increased by 500%. The transient simulations (100 h simulated) demonstrated that the dynamic response of the BC wall was shorter than that of the TM wall, even when the TM wall was simulated with initial thermal conditions that were more advantageous than those for the BC wall. The BC system reached a periodic stabilized regime within 24 h, whereas the TM system failed to stabilize in 100 h. The results show that for both TM and BC structures, the interlayer thickness scarcely influenced the temperature of the environment reached (the temperature peak increased up to 3–4% as the interlayer thickness was increased by 500%), while larger air speed changes were observed in the BC system in the transient state compared with the TM system. Thus, in the TM system, the outlet air velocity was practically constant as the interlayer thickness was increased; in contrast, the outlet velocity peak increased up to 50% in the BC system. Moreover, the BC wall presented a quicker response to satisfy the ambient thermal loads.
Open AccessSteady- and Transient-State CFD Simulations of a Modified Barra–Costantini Solar System in Comparison with a Traditional Trombe–Michel Wall
Passive solar systems are one of most important strategies to reduce the heating loads of buildings. The Trombe–Michel (TM) wall and its variants are some of the better-known structures in the field of solar systems. An alternative to the TM wall is the Barra–Costantini (BC) system. In the present paper, CFD numerical simulations, both in steady and transient states, of modified BC and TM walls were carried out in the winter season. Different interspace thicknesses were simulated in order to evaluate their effects on the temperature field and air velocity, and the numerical results were compared among them. It was found that the BC system offers greater hot air flow compared with the TM wall; the mass flow rate increased up to 43% in the BC system and up 28% in the TM system when the interlayer thickness was increased by 500%. The transient simulations (100 h simulated) demonstrated that the dynamic response of the BC wall was shorter than that of the TM wall, even when the TM wall was simulated with initial thermal conditions that were more advantageous than those for the BC wall. The BC system reached a periodic stabilized regime within 24 h, whereas the TM system failed to stabilize in 100 h. The results show that for both TM and BC structures, the interlayer thickness scarcely influenced the temperature of the environment reached (the temperature peak increased up to 3–4% as the interlayer thickness was increased by 500%), while larger air speed changes were observed in the BC system in the transient state compared with the TM system. Thus, in the TM system, the outlet air velocity was practically constant as the interlayer thickness was increased; in contrast, the outlet velocity peak increased up to 50% in the BC system. Moreover, the BC wall presented a quicker response to satisfy the ambient thermal loads.
- Open Access
- 1 January 2024
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 11 (1) , 376
Power Enhancement and Energy Efficiency of a Wind Turbine Equipped with a Slotted Jet: 3D-DDES Numerical Simulations of the S809 Airfoil
The Volume 11, published for JFFHMT Journal.
- 1 January 2024
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 11 (1) , 376
Open AccessPower Enhancement and Energy Efficiency of a Wind Turbine Equipped with a Slotted Jet: 3D-DDES Numerical Simulations of the S809 Airfoil
The Volume 11, published for JFFHMT Journal.
- Open Access
Preliminary Results of Heat Transfer and Pressure Drop Measurements on Al2O3/H2O Nanofluids through a Lattice Channel
A nanofluid is composed of a base fluid with a suspension of nanoparticles that improve the base fluid’s thermophysical properties. In this work, the authors have conducted experimental tests on an alumina-based nanofluid (Al2O3/H2O) moving inside a 3D-printed lattice channel. The unit cell’s lattice shape can be considered a double X or a double pyramidal truss with a common vertex. The test channel is 80 mm long and has a cross-sectional area, without an internal lattice with that has the dimensions H × W, with H = 5 mm and W = 15 mm. A nanofluid and a lattice duct can represent a good compound technique for enhancing heat transfer. The channel is heated by an electrical resistance wound onto its outer surface. The heat transfer rate absorbed by the nanofluid, the convective heat transfer coefficients, and the pressure drops are evaluated. The experimental tests are carried out at various volumetric contents of nanoparticles (φ = 1.00%, φ = 1.50% and φ = 2.05%) and at various volumetric flow rates (from 0.2 L/min to 2 L/min). The preliminary results show that in the range between 0.5 L/min ÷ 2.0 L/min, the values of convective heat transfer coefficients are greater than those of pure water (φ = 0) for all concentrations of Al2O3; thus, the nanofluid absorbed a higher thermal power than the water, with an average increase of 6%, 9%, and 14% for 1.00%, 1.50% and 2.05% volume concentrations, respectively. The pressure drops are not very different from those of water; therefore, the use of nanofluids also increased the cooling efficiency of the system.
Open AccessPreliminary Results of Heat Transfer and Pressure Drop Measurements on Al2O3/H2O Nanofluids through a Lattice Channel
A nanofluid is composed of a base fluid with a suspension of nanoparticles that improve the base fluid’s thermophysical properties. In this work, the authors have conducted experimental tests on an alumina-based nanofluid (Al2O3/H2O) moving inside a 3D-printed lattice channel. The unit cell’s lattice shape can be considered a double X or a double pyramidal truss with a common vertex. The test channel is 80 mm long and has a cross-sectional area, without an internal lattice with that has the dimensions H × W, with H = 5 mm and W = 15 mm. A nanofluid and a lattice duct can represent a good compound technique for enhancing heat transfer. The channel is heated by an electrical resistance wound onto its outer surface. The heat transfer rate absorbed by the nanofluid, the convective heat transfer coefficients, and the pressure drops are evaluated. The experimental tests are carried out at various volumetric contents of nanoparticles (φ = 1.00%, φ = 1.50% and φ = 2.05%) and at various volumetric flow rates (from 0.2 L/min to 2 L/min). The preliminary results show that in the range between 0.5 L/min ÷ 2.0 L/min, the values of convective heat transfer coefficients are greater than those of pure water (φ = 0) for all concentrations of Al2O3; thus, the nanofluid absorbed a higher thermal power than the water, with an average increase of 6%, 9%, and 14% for 1.00%, 1.50% and 2.05% volume concentrations, respectively. The pressure drops are not very different from those of water; therefore, the use of nanofluids also increased the cooling efficiency of the system.
- Open Access
- 15 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (14) , 6511
Dimensionless Correlations for Natural Convection Heat Transfer from a Pair of Vertical Staggered Plates Suspended in Free Air
Buoyancy-induced convection from a pair of staggered heated vertical plates suspended in free air is studied numerically with the main scope to investigate the basic heat and momentum transfer features and to determine in what measure any independent variable affects the thermal performance of each plate and both plates. A computational code based on the SIMPLE-C algorithm for pressure-velocity coupling is used to solve the system of the governing conservation equations of mass, momentum and energy. Numerical simulations are carried out for different values of the Rayleigh number based on the plate length, as well as of the horizontal separation distance between the plates and their vertical alignment, which are both normalized by the plate length. It is observed that an optimal separation distance between the plates for the maximum heat transfer rate related to the Rayleigh number and the vertical alignment of the plates does exist. Based on the results obtained, suitable dimensionless heat transfer correlations are developed for each plate and for the entire system.
- 15 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (14) , 6511
Open AccessDimensionless Correlations for Natural Convection Heat Transfer from a Pair of Vertical Staggered Plates Suspended in Free Air
Buoyancy-induced convection from a pair of staggered heated vertical plates suspended in free air is studied numerically with the main scope to investigate the basic heat and momentum transfer features and to determine in what measure any independent variable affects the thermal performance of each plate and both plates. A computational code based on the SIMPLE-C algorithm for pressure-velocity coupling is used to solve the system of the governing conservation equations of mass, momentum and energy. Numerical simulations are carried out for different values of the Rayleigh number based on the plate length, as well as of the horizontal separation distance between the plates and their vertical alignment, which are both normalized by the plate length. It is observed that an optimal separation distance between the plates for the maximum heat transfer rate related to the Rayleigh number and the vertical alignment of the plates does exist. Based on the results obtained, suitable dimensionless heat transfer correlations are developed for each plate and for the entire system.
- 1 June 2016
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 104, 54-67
Numerical simulation of the optimal spacing for a radial finned tube cooled by a rectangular jet. I – Average thermal results
- 1 June 2016
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 104, 54-67
Numerical simulation of the optimal spacing for a radial finned tube cooled by a rectangular jet. I – Average thermal results
- 9 November 2012
- Published by ASME International
- p. 2679-2688
Experimental and Numerical Heat Transfer on a Cylinder Cooled by Two Rectangular Jets of Different Heights
The present paper presents experimental measurements of heat transfer on a cylinder, cooled by two rectangular jets of the same width but different height, H, in order to investigate the influence of the jet height on the local and the average cooling rates, because one of the problems in the heat transfer with jet flow is the convenience to choose the height of the jet in comparison to the height of the impinged object. The cylinder, heated by electric current, is set at several distances from the jet exit, x, on the symmetrical plane of symmetry, i.e. in a two-dimensional geometry, in order to find the optimal position which realizes the maximum heat transfer. The experimental heat transfer on the impingement shows that the local Nusselt number, defined with the cylinder diameter, D, is greater for the smaller slot because velocity is slightly higher but the average Nusselt numbers, defined with the cylinder diameter, D, are quite similar because the higher slot has a greater surface of impingement. Local and average Nusselt numbers are in qualitative agreement only if are compared with the same dimensionless distance, x/H, which can be interpreted as the ratio Rex/ReH, which is per unit of mass flow rate or is independent of the mass flow rate. Numerical simulations are carried out with a two-equations turbulent model using the RNG k-ε approach, on a cylinder with the same thickness of the experiments or without thickness. The numerical simulations of the cylinder without thickness are in acceptable agreement for what concern the average Nusselt numbers. The local Nusselt numbers are in fair agreement only if the cylinder has the thickness of the experiments, independently of the heat flow conditions, i.e. uniformly throughout the thickness or from the inner surface.
- 9 November 2012
- Published by ASME International
- p. 2679-2688
Experimental and Numerical Heat Transfer on a Cylinder Cooled by Two Rectangular Jets of Different Heights
The present paper presents experimental measurements of heat transfer on a cylinder, cooled by two rectangular jets of the same width but different height, H, in order to investigate the influence of the jet height on the local and the average cooling rates, because one of the problems in the heat transfer with jet flow is the convenience to choose the height of the jet in comparison to the height of the impinged object. The cylinder, heated by electric current, is set at several distances from the jet exit, x, on the symmetrical plane of symmetry, i.e. in a two-dimensional geometry, in order to find the optimal position which realizes the maximum heat transfer. The experimental heat transfer on the impingement shows that the local Nusselt number, defined with the cylinder diameter, D, is greater for the smaller slot because velocity is slightly higher but the average Nusselt numbers, defined with the cylinder diameter, D, are quite similar because the higher slot has a greater surface of impingement. Local and average Nusselt numbers are in qualitative agreement only if are compared with the same dimensionless distance, x/H, which can be interpreted as the ratio Rex/ReH, which is per unit of mass flow rate or is independent of the mass flow rate. Numerical simulations are carried out with a two-equations turbulent model using the RNG k-ε approach, on a cylinder with the same thickness of the experiments or without thickness. The numerical simulations of the cylinder without thickness are in acceptable agreement for what concern the average Nusselt numbers. The local Nusselt numbers are in fair agreement only if the cylinder has the thickness of the experiments, independently of the heat flow conditions, i.e. uniformly throughout the thickness or from the inner surface.