Fabian Pianezzi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fabian Pianezzi has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Stephan Buecheler
Laboratory for Thin Films and Photovoltaics, Empa—Swiss Federal Laboratories for Materials Science and Technology, Überlandstrasse 129, CH-8600 Dübendorf, Switzerland
3 shared publications Ayodhya N. Tiwari
Laboratory for Thin Films and Photovoltaics Empa, Swiss Federal Laboratories for Materials Science and Technology Ueberlandstrasse 129 8600 Duebendorf Switzerland
2 shared publicationsBenjamin Bissig
Laboratory for Thin Films and Photovoltaics Empa, Swiss Federal Laboratories for Materials Science and Technology Ueberlandstrasse 129 8600 Duebendorf Switzerland
2 shared publications- Carolin M. Sutter-Fella
Molecular Foundry
2 shared publications Patrick Reinhard
Laboratory for Thin Films and Photovoltaics Empa, Swiss Federal Laboratories for Materials Science and Technology Ueberlandstrasse 129 8600 Duebendorf Switzerland
2 shared publicationsShiro Nishiwaki
Laboratory for Thin Films and Photovoltaics Empa, Swiss Federal Laboratories for Materials Science and Technology Ueberlandstrasse 129 8600 Duebendorf Switzerland
2 shared publications
Latest Publications
- 22 April 2014
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 23 (7) , 892-900
Influence of Ni and Cr impurities on the electronic properties of Cu(In,Ga)Se2thin film solar cells
Deposition of Cu(In,Ga)Se2(CIGS) thin film solar cells on metallic substrate is an attractive approach for development of low cost solar modules. However, in such devices, special care has to be taken to avoid diffusion of impurities, such as Fe, Ni, and Cr, from the substrate into the active layers. In this work, the influence of Ni and Cr impurities on the electronic properties of CIGS thin film solar cells is investigated in detail. Impurities were introduced into the CIGS layer by diffusion during the CIGS deposition process from a Ni or Cr precursor layer below the Mo electrical back contact. A high temperature and a low temperature CIGS deposition process were applied in order to correlate the changes in the photovoltaic parameters with the amount of impurities diffused into the absorber layer. Solar cells with Ni and Cr impurities show a reduction in the device performance, whereas the effect was most pronounced in Ni containing devices. The presence of deep defect levels in the absorber layer was identified with admittance spectroscopy and can be related to Ni and Cr impurities, which diffused into the CIGS layer according to secondary ion mass spectroscopy depth profiles and inductively coupled plasma mass spectrometry. Copyright © 2014 John Wiley & Sons, Ltd.
- 22 April 2014
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 23 (7) , 892-900
Influence of Ni and Cr impurities on the electronic properties of Cu(In,Ga)Se2thin film solar cells
Deposition of Cu(In,Ga)Se2(CIGS) thin film solar cells on metallic substrate is an attractive approach for development of low cost solar modules. However, in such devices, special care has to be taken to avoid diffusion of impurities, such as Fe, Ni, and Cr, from the substrate into the active layers. In this work, the influence of Ni and Cr impurities on the electronic properties of CIGS thin film solar cells is investigated in detail. Impurities were introduced into the CIGS layer by diffusion during the CIGS deposition process from a Ni or Cr precursor layer below the Mo electrical back contact. A high temperature and a low temperature CIGS deposition process were applied in order to correlate the changes in the photovoltaic parameters with the amount of impurities diffused into the absorber layer. Solar cells with Ni and Cr impurities show a reduction in the device performance, whereas the effect was most pronounced in Ni containing devices. The presence of deep defect levels in the absorber layer was identified with admittance spectroscopy and can be related to Ni and Cr impurities, which diffused into the CIGS layer according to secondary ion mass spectroscopy depth profiles and inductively coupled plasma mass spectrometry. Copyright © 2014 John Wiley & Sons, Ltd.
- Top Cited Papers
- 18 March 2014
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 16 (19) , 8843-8851
Unveiling the effects of post-deposition treatment with different alkaline elements on the electronic properties of CIGS thin film solar cells
Thin film solar cells with a Cu(In,Ga)Se2 (CIGS) absorber layer achieved efficiencies above 20%. In order to achieve such high performance the absorber layer of the device has to be doped with alkaline material. One possibility to incorporate alkaline material is a post deposition treatment (PDT), where a thin layer of NaF and/or KF is deposited onto the completely grown CIGS layer. In this paper we discuss the effects of PDT with different alkaline elements (Na and K) on the electronic properties of CIGS solar cells. We demonstrate that whereas Na is more effective in increasing the hole concentration in CIGS, K significantly improves the pn-junction quality. The beneficial role of K in improving the PV performance is attributed to reduced recombination at the CdS/CIGS interface, as revealed by temperature dependent J–V measurements, due to a stronger electronically inverted CIGS surface region. Computer simulations with the software SCAPS are used to verify this model. Furthermore, we show that PDT with either KF or NaF has also a distinct influence on other electronic properties of the device such as the position of the N1 signal in admittance spectroscopy and the roll-over of the J–V curve at low temperature. In view of the presented results we conclude that a model based on a secondary diode at the CIGS/Mo interface can best explain these features.
- 18 March 2014
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 16 (19) , 8843-8851
Top Cited PapersUnveiling the effects of post-deposition treatment with different alkaline elements on the electronic properties of CIGS thin film solar cells
Thin film solar cells with a Cu(In,Ga)Se2 (CIGS) absorber layer achieved efficiencies above 20%. In order to achieve such high performance the absorber layer of the device has to be doped with alkaline material. One possibility to incorporate alkaline material is a post deposition treatment (PDT), where a thin layer of NaF and/or KF is deposited onto the completely grown CIGS layer. In this paper we discuss the effects of PDT with different alkaline elements (Na and K) on the electronic properties of CIGS solar cells. We demonstrate that whereas Na is more effective in increasing the hole concentration in CIGS, K significantly improves the pn-junction quality. The beneficial role of K in improving the PV performance is attributed to reduced recombination at the CdS/CIGS interface, as revealed by temperature dependent J–V measurements, due to a stronger electronically inverted CIGS surface region. Computer simulations with the software SCAPS are used to verify this model. Furthermore, we show that PDT with either KF or NaF has also a distinct influence on other electronic properties of the device such as the position of the N1 signal in admittance spectroscopy and the roll-over of the J–V curve at low temperature. In view of the presented results we conclude that a model based on a secondary diode at the CIGS/Mo interface can best explain these features.
- 3 January 2012
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 20 (3) , 253-259
Electronic properties of Cu(In,Ga)Se2solar cells on stainless steel foils without diffusion barrier
Compared with rigid glass, manufacturing of Cu(In,Ga)Se2(CIGS) solar cells on flexible stainless steel (SS) substrates has potential to reduce production cost because of the application of roll‐to‐roll processing. Up to now, high‐efficiency cells on SS could only be achieved when the substrate is coated with a barrier layer (e.g. SiOxor Si3N4) for hindering the diffusion of impurities, especially Fe, into the CIGS layer. In this paper, the effect of these impurities on the electronic transport properties of the device is investigated. Using admittance spectroscopy, the presence of a deep defect level at around 320 meV is observed, which deteriorates the efficiency of the solar cells. Furthermore, it is shown that reducing substrate temperature during CIGS deposition is an effective alternative to a barrier layer for reducing diffusion of detrimental Fe impurities into the absorber layer. By applying a CIGS growth process for deposition at low substrate temperatures, an efficiency of 17.7%, certified by Fraunhofer Institute ISE, Freiburg, was achieved on Mo/Ti‐coated SS substrate without an additional metal‐oxide or metal‐nitride impurity diffusion barrier layer. Copyright © 2012 John Wiley & Sons, Ltd.
- 3 January 2012
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 20 (3) , 253-259
Electronic properties of Cu(In,Ga)Se2solar cells on stainless steel foils without diffusion barrier
Compared with rigid glass, manufacturing of Cu(In,Ga)Se2(CIGS) solar cells on flexible stainless steel (SS) substrates has potential to reduce production cost because of the application of roll‐to‐roll processing. Up to now, high‐efficiency cells on SS could only be achieved when the substrate is coated with a barrier layer (e.g. SiOxor Si3N4) for hindering the diffusion of impurities, especially Fe, into the CIGS layer. In this paper, the effect of these impurities on the electronic transport properties of the device is investigated. Using admittance spectroscopy, the presence of a deep defect level at around 320 meV is observed, which deteriorates the efficiency of the solar cells. Furthermore, it is shown that reducing substrate temperature during CIGS deposition is an effective alternative to a barrier layer for reducing diffusion of detrimental Fe impurities into the absorber layer. By applying a CIGS growth process for deposition at low substrate temperatures, an efficiency of 17.7%, certified by Fraunhofer Institute ISE, Freiburg, was achieved on Mo/Ti‐coated SS substrate without an additional metal‐oxide or metal‐nitride impurity diffusion barrier layer. Copyright © 2012 John Wiley & Sons, Ltd.