M. V. Chernets’
Research Subjects
M. V. Chernets’ has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
R. Ya. Yarema
Lviv Locomotive Repair Plant, Lviv, Ukraine
4 shared publicationsE. Kelbinski
Politechnika Lubelska
1 shared publicationJurij Chernets
Drohobych Ivan Franko State Pedagogical University, Drohobych, Ukraine
1 shared publicationN. M. Lebedeva
Franko Drohobych State Pedagogical University
1 shared publication- O. E. Andreikiv
Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine, Lviv, Ukraine
1 shared publication V. B. Zhidik
Franko Drohobych State Pedagogic University
1 shared publication
Latest Publications
- 1 January 2017
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 38 (1) , 23-29
A technique for calculating tribotechnical characteristics of tractive cylindrical gear of VL-10 locomotive
A technique for the design calculations of the local strength, wear, and durability of tractive cylindrical double gear of VL-10 locomotive with angular tooth correction has been suggested. The technique allows for realistic engagement conditions (parity and wear-induced changes in the tooth profile curvature). The regularities of the effect that structural (angular engagement correction) and operational (linear tooth wear) factors have on these parameters for triple–double–triple tooth engagement in this gear have been revealed. It has been established that, when considering tooth correction, there are certain optimum displacement coefficients that maximize the durability compared to the uncorrected gear. It has been shown that, if one allows for changes in the tooth-profile due to wear are allowed for, the actual durability and bearing capacity of the gear is higher. The results have been presented graphically in order to help establish regularities of the effect of engagement conditions on the tribotechnical characteristics.
- 1 January 2017
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 38 (1) , 23-29
A technique for calculating tribotechnical characteristics of tractive cylindrical gear of VL-10 locomotive
A technique for the design calculations of the local strength, wear, and durability of tractive cylindrical double gear of VL-10 locomotive with angular tooth correction has been suggested. The technique allows for realistic engagement conditions (parity and wear-induced changes in the tooth profile curvature). The regularities of the effect that structural (angular engagement correction) and operational (linear tooth wear) factors have on these parameters for triple–double–triple tooth engagement in this gear have been revealed. It has been established that, when considering tooth correction, there are certain optimum displacement coefficients that maximize the durability compared to the uncorrected gear. It has been shown that, if one allows for changes in the tooth-profile due to wear are allowed for, the actual durability and bearing capacity of the gear is higher. The results have been presented graphically in order to help establish regularities of the effect of engagement conditions on the tribotechnical characteristics.
- 5 August 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 231 (1) , 57-62
The simulation of influence of engagement conditions and technological teeth correction on contact strength, wear and durability of cylindrical spur gear of electric locomotive
The cylindrical spur tractive gear of the electric locomotive has been conducted using the author’s method of the calculation of maximum contact pressures, teeth wear and durability at technological correction of engagement at changeable, in the result of teeth wear and conditions of their contact. The regularities of tribocontact pressures change in engagement has been established after reaching the permissible wear depending on the shift coefficients in the phases of double–single–double tooth engagement. Considerable decrease of maximum tribocontact pressures is observed in the result of teeth wear in the entry phase of double-tooth engagement in comparison with their initial values. Depending on the shift coefficients, maximum (permissible) wear of wheel teeth would arise in different contact points: at the entrance into single-tooth engagement in non-corrected gear and at the exit in the presence of correction. Gear durability has its optimum at = 0.1 which is 1.22 times larger than in the absence of engagement correction.- 5 August 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 231 (1) , 57-62
The simulation of influence of engagement conditions and technological teeth correction on contact strength, wear and durability of cylindrical spur gear of electric locomotive
The cylindrical spur tractive gear of the electric locomotive has been conducted using the author’s method of the calculation of maximum contact pressures, teeth wear and durability at technological correction of engagement at changeable, in the result of teeth wear and conditions of their contact. The regularities of tribocontact pressures change in engagement has been established after reaching the permissible wear depending on the shift coefficients in the phases of double–single–double tooth engagement. Considerable decrease of maximum tribocontact pressures is observed in the result of teeth wear in the entry phase of double-tooth engagement in comparison with their initial values. Depending on the shift coefficients, maximum (permissible) wear of wheel teeth would arise in different contact points: at the entrance into single-tooth engagement in non-corrected gear and at the exit in the presence of correction. Gear durability has its optimum at = 0.1 which is 1.22 times larger than in the absence of engagement correction.- 1 March 2015
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 36 (2) , 163-169
Prediction of the life of a sliding bearing based on a cumulative wear model taking into account the lobing of the shaft contour
Using a generalized cumulative wear model, the tribocontact problem has been solved for a sliding bearing, the shaft of which has small contour lobing with various forms. The effect of lobing on the bearing life has been investigated at the complete single-area and mixed-area contact. It has been found that the ovality and trilobing of the shaft promote a rise in the service life. Features of this effect are presented graphically.
- 1 March 2015
- Published by Allerton Press in Journal of Friction and Wear
- Vol. 36 (2) , 163-169
Prediction of the life of a sliding bearing based on a cumulative wear model taking into account the lobing of the shaft contour
Using a generalized cumulative wear model, the tribocontact problem has been solved for a sliding bearing, the shaft of which has small contour lobing with various forms. The effect of lobing on the bearing life has been investigated at the complete single-area and mixed-area contact. It has been found that the ovality and trilobing of the shaft promote a rise in the service life. Features of this effect are presented graphically.
- 1 May 2013
- Published by Springer Nature in Materials Science
- Vol. 48 (6) , 752-756
A method for the evaluation of the influence of correction and wear of the teeth of a cylindrical gear on its durability and strength. Part 2. Contact strength
- 1 May 2013
- Published by Springer Nature in Materials Science
- Vol. 48 (6) , 752-756
A method for the evaluation of the influence of correction and wear of the teeth of a cylindrical gear on its durability and strength. Part 2. Contact strength
- 1 November 2012
- Published by Springer Nature in Materials Science
- Vol. 48 (3) , 289-300
A method for the evaluation of the influence of correction and wear of the teeth of a cylindrical gear on its durability and strength. Part 1. Service life and wear
- 1 November 2012
- Published by Springer Nature in Materials Science
- Vol. 48 (3) , 289-300
A method for the evaluation of the influence of correction and wear of the teeth of a cylindrical gear on its durability and strength. Part 1. Service life and wear
- 1 January 2012
- Published by Springer Nature in Materials Science
- Vol. 47 (4) , 553-560
A generalized method for the evaluation of the influence of teeth correction on the service life, wear, and contact strength of cylindrical involute gears
- 1 January 2012
- Published by Springer Nature in Materials Science
- Vol. 47 (4) , 553-560
A generalized method for the evaluation of the influence of teeth correction on the service life, wear, and contact strength of cylindrical involute gears
- 1 October 2011
- Published by Springer Nature in Materials Science
- Vol. 47 (3) , 294-300
Quasistatic contact problem for cylindrical joints with minor cutting of the contours of the bodies
- 1 October 2011
- Published by Springer Nature in Materials Science
- Vol. 47 (3) , 294-300
Quasistatic contact problem for cylindrical joints with minor cutting of the contours of the bodies
- 1 July 2011
- Published by Springer Nature in Materials Science
- Vol. 47 (1) , 45-51
Generalized method for the evaluation of wear in cylindrical involute gears
- 1 July 2011
- Published by Springer Nature in Materials Science
- Vol. 47 (1) , 45-51
Generalized method for the evaluation of wear in cylindrical involute gears
- 1 November 2009
- Published by Springer Nature in Materials Science
- Vol. 45 (6) , 859-868
Contact problem for a cylindrical joint with technological faceting of the contours of its parts
- 1 November 2009
- Published by Springer Nature in Materials Science
- Vol. 45 (6) , 859-868
Contact problem for a cylindrical joint with technological faceting of the contours of its parts
- 1 July 2009
- Published by Springer Nature in Materials Science
- Vol. 45 (4) , 595-604
Method for the evaluation of wear and durability of involute conical straight-bevel gears
- 1 July 2009
- Published by Springer Nature in Materials Science
- Vol. 45 (4) , 595-604
Method for the evaluation of wear and durability of involute conical straight-bevel gears