Aleksandra Pataric
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Aleksandra Pataric has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Marija Mihailović
Institute of Chemistry, Technology and Metallurgy, National Institute of the Republic of Serbia, University of Belgrade, Njegoševa 12, 11000 Belgrade, Serbia
4 shared publications - Branislav Marković
Institute for Technology of Nuclear and Other Mineral Raw Materials
2 shared publications Miroslav Sokic
Institute for Technology of Nuclear and Other Mineral Raw Materials, Belgrade
2 shared publicationsVladislav Matkovic
Institute for Technology of Nuclear and Other Mineral Raw Materials, Belgrade
2 shared publications- Zvonko Gulišija
Institute for Technology of Nuclear and Other Mineral Raw Materials
2 shared publications Djordje Janackovic
NEMA
1 shared publication
Latest Publications
- Open Access
Cleavage Fracture of the Air Cooled Medium Carbon Microalloyed Forging Steels with Heterogeneous Microstructures
Cleavage fracture of the V and Ti-V microalloyed forging steels was investigated by the four-point bending testing of the notched specimens of Griffith-Owen’s type at −196 °C, in conjunction with the finite element analysis and the fractographic examination by scanning electron microscopy. To assess the mixed microstructure consisting mostly of the acicular ferrite, alongside proeutectoid ferrite grains and pearlite, the samples were held at 1250 °C for 30 min and subsequently cooled instill air. Cleavage fracture was initiated in the matrix under the high plastic strains near the notch root of the four-point bending specimens without the participation of the second phase particles in the process. Estimated values of the effective surface energy for the V and the Ti-V microalloyed steel of 37 Jm−2 and 74 Jm−2, respectively, and the related increase of local critical fracture stress were attributed to the increased content of the acicular ferrite. It was concluded that the observed increase of the local stress for cleavage crack propagation through the matrix was due to the increased number of the high angle boundaries, but also that the acicular ferrite affects the cleavage fracture mechanism by its characteristic stress–strain response with relatively low yield strength and considerable ductility at −196 °C.
Open AccessCleavage Fracture of the Air Cooled Medium Carbon Microalloyed Forging Steels with Heterogeneous Microstructures
Cleavage fracture of the V and Ti-V microalloyed forging steels was investigated by the four-point bending testing of the notched specimens of Griffith-Owen’s type at −196 °C, in conjunction with the finite element analysis and the fractographic examination by scanning electron microscopy. To assess the mixed microstructure consisting mostly of the acicular ferrite, alongside proeutectoid ferrite grains and pearlite, the samples were held at 1250 °C for 30 min and subsequently cooled instill air. Cleavage fracture was initiated in the matrix under the high plastic strains near the notch root of the four-point bending specimens without the participation of the second phase particles in the process. Estimated values of the effective surface energy for the V and the Ti-V microalloyed steel of 37 Jm−2 and 74 Jm−2, respectively, and the related increase of local critical fracture stress were attributed to the increased content of the acicular ferrite. It was concluded that the observed increase of the local stress for cleavage crack propagation through the matrix was due to the increased number of the high angle boundaries, but also that the acicular ferrite affects the cleavage fracture mechanism by its characteristic stress–strain response with relatively low yield strength and considerable ductility at −196 °C.
- Open Access
- 31 December 2014
- Published by TechnoFit Academic Publishers LLC in Metallurgical and Materials Engineering
- Vol. 20 (4) , 247-254
The use of electromagnetic field in designing the high quality Al alloys for hot forging process
This work presents a way to obtain the better quality of EN AW 7075 aluminum high-strength alloy by application of electromagnetic field (EMF) during the casting process. In this way, the uniform fine-grained microstructure, and hence the better mechanical properties of the alloy can be achieved. The microstructure and mechanical characterization for samples obtained with and without EMF were performed. The application of numerical simulation for hot forging process, using appropriate software, is efficient and highly useful tool for problem prediction in industrial production, reducing the time and costs in the process of development of new products. The input data of high strength Al-alloy EN AW-7075 is used for simulation because it enables the development of parts with complex dimensions and shape.
- 31 December 2014
- Published by TechnoFit Academic Publishers LLC in Metallurgical and Materials Engineering
- Vol. 20 (4) , 247-254
Open AccessThe use of electromagnetic field in designing the high quality Al alloys for hot forging process
This work presents a way to obtain the better quality of EN AW 7075 aluminum high-strength alloy by application of electromagnetic field (EMF) during the casting process. In this way, the uniform fine-grained microstructure, and hence the better mechanical properties of the alloy can be achieved. The microstructure and mechanical characterization for samples obtained with and without EMF were performed. The application of numerical simulation for hot forging process, using appropriate software, is efficient and highly useful tool for problem prediction in industrial production, reducing the time and costs in the process of development of new products. The input data of high strength Al-alloy EN AW-7075 is used for simulation because it enables the development of parts with complex dimensions and shape.
- Open Access
- 1 January 2014
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 20 (3) , 397-405
The possibilities of obtaining metallic calcium from Serbian carbonate mineral raw materials
The experimental investigations defined both the technological scheme of the calcium production from limestone by aluminothermic process and the basic operating parameters of the particular technological phases. The limestone with high content of Mg, Na and K was used in the paper. X-ray analysis reveals that the samples contain mainly calcite with small amount of dolomite. At first, the influence of temperature, time and granulometry on the calcium carbonate calcination was examined. The dissociation process was completed in 10-15 min at 1200?C, and dissociation rate increases with decreasing of particle size up to 5 mm. Afterwards, the aluminothermic reduction process of calcium oxide was investigated. At the temperature 1200?C, and vacuum of at least 3 kPa, the reduction process completed within 2 hours. The chemical composition of calcium oxide and calcium showed increased content of magnesium oxide and alkaline oxides (especially sodium).
- 1 January 2014
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 20 (3) , 397-405
Open AccessThe possibilities of obtaining metallic calcium from Serbian carbonate mineral raw materials
The experimental investigations defined both the technological scheme of the calcium production from limestone by aluminothermic process and the basic operating parameters of the particular technological phases. The limestone with high content of Mg, Na and K was used in the paper. X-ray analysis reveals that the samples contain mainly calcite with small amount of dolomite. At first, the influence of temperature, time and granulometry on the calcium carbonate calcination was examined. The dissociation process was completed in 10-15 min at 1200?C, and dissociation rate increases with decreasing of particle size up to 5 mm. Afterwards, the aluminothermic reduction process of calcium oxide was investigated. At the temperature 1200?C, and vacuum of at least 3 kPa, the reduction process completed within 2 hours. The chemical composition of calcium oxide and calcium showed increased content of magnesium oxide and alkaline oxides (especially sodium).
- 1 January 2013
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 54 (10) , 1925-1929
Chemical Thermodynamic Processes at Metal-Mold Interface
- 1 January 2013
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 54 (10) , 1925-1929
Chemical Thermodynamic Processes at Metal-Mold Interface
- 16 August 2011
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (2) , 793-796
Quantitative metallographic assessment of the electromagnetic casting influence on the microstructure of 7075 Al alloy
- 16 August 2011
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (2) , 793-796
Quantitative metallographic assessment of the electromagnetic casting influence on the microstructure of 7075 Al alloy
- Open Access
- 1 January 2011
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 17 (1) , 45-52
Electrophoretically deposited nanosized hydroxyapatite coatings on 316LVM stainless steel for orthopaedic implants
Hydroxyapatite is widely used bioceramic material in implant coatings research because of its bioactive behavior when being deposited onto the metallic implant and compatibility to the human bones composition. The coating of nanosized hydroxyapatite was electrophoretically deposited on blasted surface of stainless steel 316LVM samples at constant voltage, for different deposition times and subsequently sintered in both, vacuum and argon atmosphere, at 1040?C and 1000?C, respectively. Although sintering temperatures needed to achieve highly dense coatings can cause HAp coating phase changes, the possibility to obtain a bioactive coating on 316LVM substrate, without the coatings phase changes due to the nature of the used stoichiometric nanostructured hydroxyapatite is presented in this work. The thermal stability of the used HAp powder was assessed by DTA-TG analyses over the temperature range of 23?C-1000?C, i.e. at the or nearby experimental sintering temperature. The microstructure characterization was accomplished using SEM, while phase composition was determined using XRD.
- 1 January 2011
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 17 (1) , 45-52
Open AccessElectrophoretically deposited nanosized hydroxyapatite coatings on 316LVM stainless steel for orthopaedic implants
Hydroxyapatite is widely used bioceramic material in implant coatings research because of its bioactive behavior when being deposited onto the metallic implant and compatibility to the human bones composition. The coating of nanosized hydroxyapatite was electrophoretically deposited on blasted surface of stainless steel 316LVM samples at constant voltage, for different deposition times and subsequently sintered in both, vacuum and argon atmosphere, at 1040?C and 1000?C, respectively. Although sintering temperatures needed to achieve highly dense coatings can cause HAp coating phase changes, the possibility to obtain a bioactive coating on 316LVM substrate, without the coatings phase changes due to the nature of the used stoichiometric nanostructured hydroxyapatite is presented in this work. The thermal stability of the used HAp powder was assessed by DTA-TG analyses over the temperature range of 23?C-1000?C, i.e. at the or nearby experimental sintering temperature. The microstructure characterization was accomplished using SEM, while phase composition was determined using XRD.