Philippe Darnis
Research Subjects
Philippe Darnis has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Alain Gérard
Université de Bordeaux
5 shared publications - Claudiu-Florinel Bisu
Machines and Production Systems Departament "POLITEHNICA" University of Bucharest Splaiul Independenţei no. 313 Street ROMANIA
5 shared publications - Raynald Laheurte
University of Bordeaux
3 shared publications - Jean-Yves K'Nevez
Machine and Manufacturing Systems Department Bucharest University POLITEHNICA of Bucharest Romania
2 shared publications - Olivier Cahuc
University of Bordeaux
2 shared publications - Olivier Cahuc
UMR 5295 University of Bordeaux CNRS I2MI Département MPI 351 cours de la Libération 33405 Talence FRANCE
2 shared publications
Latest Publications
- Open Access
Displacements analysis of self-excited vibrations in turning
The actual research deals with determining by a new protocol the necessary parameters considering a three-dimensional model to simulate in a realistic way the turning process on machine tool. This paper is dedicated to the experimental displacements analysis of the block tool / block workpiece with self-excited vibrations. In connexion with turning process, the self-excited vibrations domain is obtained starting from spectra of two accelerometers. The existence of a displacements plane attached to the tool edge point is revealed. This plane proves to be inclined compared to the machines tool axes. We establish that the tool tip point describes an ellipse. This ellipse is very small and can be considered as a small straight line segment for the stable cutting process (without vibrations). In unstable mode (with vibrations) the ellipse of displacements is really more visible. A difference in phase occurs between the tool tip displacements on the radial direction and on the cutting one. The feed motion direction and the cutting one are almost in phase. The values of the long and small ellipse axes (and their ratio) shows that these sizes are increasing with the feed rate value. The axis that goes through the stiffness center and the tool tip represents the maximum stiffness direction. The maximum (resp. minimum) stiffness axis of the tool is perpendicular to the large (resp. small) ellipse displacements axis. FFT analysis of the accelerometers signals allows to reach several important parameters and establish coherent correlations between tool tip displacements and the static - elastic characteristics of the machine tool components tested.
Open AccessDisplacements analysis of self-excited vibrations in turning
The actual research deals with determining by a new protocol the necessary parameters considering a three-dimensional model to simulate in a realistic way the turning process on machine tool. This paper is dedicated to the experimental displacements analysis of the block tool / block workpiece with self-excited vibrations. In connexion with turning process, the self-excited vibrations domain is obtained starting from spectra of two accelerometers. The existence of a displacements plane attached to the tool edge point is revealed. This plane proves to be inclined compared to the machines tool axes. We establish that the tool tip point describes an ellipse. This ellipse is very small and can be considered as a small straight line segment for the stable cutting process (without vibrations). In unstable mode (with vibrations) the ellipse of displacements is really more visible. A difference in phase occurs between the tool tip displacements on the radial direction and on the cutting one. The feed motion direction and the cutting one are almost in phase. The values of the long and small ellipse axes (and their ratio) shows that these sizes are increasing with the feed rate value. The axis that goes through the stiffness center and the tool tip represents the maximum stiffness direction. The maximum (resp. minimum) stiffness axis of the tool is perpendicular to the large (resp. small) ellipse displacements axis. FFT analysis of the accelerometers signals allows to reach several important parameters and establish coherent correlations between tool tip displacements and the static - elastic characteristics of the machine tool components tested.
- Open Access
Determination Du Centre De Raideur Pour Les Machines-Outils - Application Au Tournage
The determination of the stiffness center of a machine tool is a major element for knowing the dynamic behavior of this one. This stiffness center can be obtained from a static characterization of the machine tool. For an operation of turning, we present an experimental protocol to determine the stiffness matrix, then by inversion, the associated flexibility matrix. This step makes it possible to establish the privileged directions of the movement associated with the maximum and minimal stiffness as well as the stiffness center. Through this step, it is observed that, at the time of an operation of turning, the movement of the point of the tool is carried out according to an ellipse located in a tilted average plan compared to the machine spindle. This movement is linked with the self-excited vibrations. This analysis could be exploited and transposed in the case of the High Speed Machining. It will make it possible to predict various aspects of machining related to the behavior of the tool in the process of cut.
Open AccessDetermination Du Centre De Raideur Pour Les Machines-Outils - Application Au Tournage
The determination of the stiffness center of a machine tool is a major element for knowing the dynamic behavior of this one. This stiffness center can be obtained from a static characterization of the machine tool. For an operation of turning, we present an experimental protocol to determine the stiffness matrix, then by inversion, the associated flexibility matrix. This step makes it possible to establish the privileged directions of the movement associated with the maximum and minimal stiffness as well as the stiffness center. Through this step, it is observed that, at the time of an operation of turning, the movement of the point of the tool is carried out according to an ellipse located in a tilted average plan compared to the machine spindle. This movement is linked with the self-excited vibrations. This analysis could be exploited and transposed in the case of the High Speed Machining. It will make it possible to predict various aspects of machining related to the behavior of the tool in the process of cut.
- 5 February 2009
- Published by Springer Nature in International Journal of Material Forming
- Vol. 2 (2) , 93-105
New method to characterize a machining system: application in turning
- 5 February 2009
- Published by Springer Nature in International Journal of Material Forming
- Vol. 2 (2) , 93-105
New method to characterize a machining system: application in turning
- 3 December 2008
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 44 (1-2) , 1-16
Displacements analysis of self-excited vibrations in turning
- 3 December 2008
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 44 (1-2) , 1-16
Displacements analysis of self-excited vibrations in turning
- 19 April 2008
- Published by Springer Nature in International Journal of Material Forming
- Vol. 1 (S1) , 949-952
Multi-layer Materials. Qualitative Approach of the Process
- 19 April 2008
- Published by Springer Nature in International Journal of Material Forming
- Vol. 1 (S1) , 949-952
Multi-layer Materials. Qualitative Approach of the Process
- Open Access
Nouvelle analyse des phénomènes vibratoires en tournage
In the cutting process, machine-tools vibrations are generally a real problem when the amplitude crosses the limits of dimensional or surface quality workpiece precision required. It is necessary to develop models taking into account the three-dimensional vibratory approach to control the vibrations phenomena. An experimental study has been realized to understand the behavior of the cutting system and to identify its vibrations properties. The displacement's localization of the tool in a spatial plan, showed by the experimental results, allows us to simplify the three-dimensional dynamical model. In this study, the experimental approach is completely presented and the first points of the three dimensional vibratory model are proposed according to the experimental results.
Open AccessNouvelle analyse des phénomènes vibratoires en tournage
In the cutting process, machine-tools vibrations are generally a real problem when the amplitude crosses the limits of dimensional or surface quality workpiece precision required. It is necessary to develop models taking into account the three-dimensional vibratory approach to control the vibrations phenomena. An experimental study has been realized to understand the behavior of the cutting system and to identify its vibrations properties. The displacement's localization of the tool in a spatial plan, showed by the experimental results, allows us to simplify the three-dimensional dynamical model. In this study, the experimental approach is completely presented and the first points of the three dimensional vibratory model are proposed according to the experimental results.
- 4 June 2007
- Published by Lavoisier in International Journal of Forming Processes
- Vol. 10 (2) , 235-269
Mechanical and Thermal Experiments in Cutting Process for New Behaviour Law
Mechanical and Thermal Experiments in Cutting Process for New Behaviour Law
- 4 June 2007
- Published by Lavoisier in International Journal of Forming Processes
- Vol. 10 (2) , 235-269
Mechanical and Thermal Experiments in Cutting Process for New Behaviour Law
Mechanical and Thermal Experiments in Cutting Process for New Behaviour Law